Thingiverse
Tasco Rifle Scope Cap by 3DMaka
by Thingiverse
Last crawled date: 3 years, 1 month ago
Air "snug" Cap for Tasco 3-7X20 rifle cap.. Nice Fit... Easy and quick to remove and replace.
This is for the front end of the scope,, usually store my rifle with butt / stock down... so dust usually clogs the lens
Make spares.. I lost the originals in no time
This fits the front of scope nicely.. but fits the rear loosely...Measured 0.40mm difference between Front and rear.
Can be used for rear end.. just adjust "slicer" percentage
This is for the front end of the scope,, usually store my rifle with butt / stock down... so dust usually clogs the lens
Make spares.. I lost the originals in no time
This fits the front of scope nicely.. but fits the rear loosely...Measured 0.40mm difference between Front and rear.
Can be used for rear end.. just adjust "slicer" percentage
Similar models
thingiverse
free
Tasco 4 x 15 Rifle Scope Shade Shroud
... a scope shade shroud for a tasco 4 x 15 rifle scope.
if you print this please take a picture and share, i would love to see it!
thingiverse
free
Steampunk Gun Mod for "Simba Planet Fighter Light" by 7Steam
... parts for the rifle scope can be equipped with an cabochon glass to mimics real lenses. (30mm at the front and 18mm at the rear)
thingiverse
free
Airsoft Prop RPG-26 Aglen by Encoded
...ight
top tube
end sleeve (complete)
end sleeve tube connector
end cap (complete)
end cap clip (complete)
end cap clip sling mount
thingiverse
free
Rifle Scope Turret by TheInsideMan
...pe turret by theinsideman
thingiverse
scope turret which connects via two small screws. fits most lower end and air-soft scopes.
thingiverse
free
Scope Flip Caps - Flip up caps for rifle scopes by PSomeone
... block so easy to re scale.
would be glad to post custom sizing requests just need to know od of the eye piece and tube in front.
thingiverse
free
Nerf Rifle Scope by lexa1203
...nerf rifle scope by lexa1203
thingiverse
for hasbro nerf - "rifle scope"
thingiverse
free
AR-15 Front & Rear Pins with End Caps by imrelaxed
...ce for minimal receiver wobble, you may need to sand them down a bit or reprint at 98% scaling if they don't fit immediately.
thingiverse
free
Dishwasher Rear Rail End Cap by indusMaker
...1/dishwasher-rear-rail-cap---pack-of-2?appliancetypeid=1083http://www.amazon.com/plastic-rear-rail-beko-dishwashers/dp/b00l37y1mm
thingiverse
free
Lens cap for Pard nv007 bajonet mount by Arve2
...onet mount. e.g. if you wish to keep the pard mount on your scope but the nv007 in hand, and still protect your rifle scope lens.
thingiverse
free
Custom Nerf Sniper Scope (TF2 Inspired) by Speed_strike
... up a shot to exactly where you're aiming.
feel free to print this yourself! if you do, please send some quality pictures! :)
Tasco
thingiverse
free
telescope aim mount replacement for tasco
...telescope aim mount replacement for tasco
thingiverse
broke mine during a move, and made a replacement for it.
thingiverse
free
Tasco 4 x 15 Rifle Scope Shade Shroud
... a scope shade shroud for a tasco 4 x 15 rifle scope.
if you print this please take a picture and share, i would love to see it!
thingiverse
free
Viewfinder sight for Tasco 10x25 binoculars by BManx2000
...; sight that helps you line up your binoculars to the target. it adds no bulk to the binoculars and still allows them to fold up.
thingiverse
free
Tasco 60mm Telescope Adapter by ApertureEngineering
...screw and nut (the nut is placed on the inside of the hexagonal hole). the two halves screw together with #6-32 screws and nuts.
thingiverse
free
Tasco XR8 Flashlight Wall Mount by hypercoffeedude
...you need to make adjustments. if you have any questions, comments, or thoughts on how to improve it, let me know in the comments.
thingiverse
free
Tasco Mini Binocular repair part by UechiMike
...desk fusion 360 and i have a replacement part that should hold up better than the original. now the binoculars aren't trash.
thingiverse
free
Fine Focus Knob for Tasco Telescope by coza73
...tside diameter 58mm
inside diameter 29 to 30mm
this has been designed in fusion 360 and i have included the f3d file with the stl
thingiverse
free
Filter rings for Solar Eclipse filter material by Jeffwaz
...allow you to glue solar eclipse filter film to. tasco 10 x 50 has 62mm inner diameter focal 8...
thingiverse
free
Sony E-Mount To Microscope Adapter
...mount a sony e-mount camera body to an old tasco microscope. the part that goes into the microscope is...
3Dmaka
thingiverse
free
Camera Lens Cap Flexible TPU by 3DMaka
...camera cap flexible tpu
sized for action cam, see: https://www.thingiverse.com/thing:2457578
or
lens dia. of 22.60 mm / .5 mm +/-
thingiverse
free
Hammer Hold / Holder by 3DMaka
...is sized for about a 1" + (28mm) round hammer head.
haven't had a chance to print it yet. let me know if you make one..
thingiverse
free
Drone RC Antenna Spread by 3DMaka
...ds to mount the antennas pointing 90 degrees from one another so that one of them is always receiving a signal at any given time.
thingiverse
free
Ice Cube Maker / Chiller For Thermos by 3DMaka
...large ice cubes. freeze.. than thaw in warm water..pop 2 in
haven't printed this yet.. let me know how it works out... thanks
thingiverse
free
Anet A8 Bed Spring Booties by 3DMaka
...s) help keeps springs straight.. and in the end run.. maybe of no real benefit..
print 2 per spring, sized for anet 8 builds 2017
thingiverse
free
Motor Wire Clamp / Harness / Anchor Anet A8 X Motor by 3DMaka
...ires would break.
nice snug fit.. est about 1lb of holding force.. depending on printer... adjust slice scaling as needed for fit
thingiverse
free
Lithium Grease Spray tube holder / Keeper by 3DMaka
... temp to 205c half way thru / fan on
use double sided tape to secure to can / wipe can and " thing" with alcohol prior.
thingiverse
free
Anet A8 Z Hieght / Stop Micro Switch Adjustment by 3DMaka
..... this can be printed to set the height needed for setting z height.. when slicing set z height as applicable (leave x,y as is)
thingiverse
free
Eachine Propeller Guard / Drone E58 / Little Mavic by 3DMaka
...ut more weight.
for more info on the white colored connector for the propeller ... see:https://www.thingiverse.com/thing:2797871
Scope
thingiverse
free
Scope by Dape
...scope by dape
thingiverse
scope
thingiverse
free
Airsoft Scope
...thingiverse
this is a scope for airsoft that i am printing for my friend who does not want to spend money on an expensive scope.
thingiverse
free
scope mount for dental scope by Sigi169
...ental scope by sigi169
thingiverse
upgraded mount for renfert scope
the pin is merely for testing fit...don't need this file
thingiverse
free
Scope cover
...scope cover
thingiverse
it's for a 40mm scope.
just add an o-ring and fit it.
thingiverse
free
Gopro hero 5 scope mount for 48mm scope by warthrob
...gopro hero 5 scope mount for 48mm scope by warthrob
thingiverse
gopro hero 5 scope mount for 48mm scope
thingiverse
free
nerf scope by Derek32
...nerf scope by derek32
thingiverse
a nerf scope
thingiverse
free
Scope by Mav7
...scope by mav7
thingiverse
*
thingiverse
free
Scope rail by rundown
...scope rail by rundown
thingiverse
scope rail for a lower rail.
thingiverse
free
60mm finder scope / guide scope tube guard
... scope tube. it allows you to tighten the adjustment screws without damage to the tube. obviously you need to print two of these.
thingiverse
free
Nerf Scope by MartijnRoozendaal
...nerf scope by martijnroozendaal
thingiverse
simple glue construction scope for nerf guns.
Rifle
thingiverse
free
Rifle
...rifle
thingiverse
one rifle for your legoheim warband.
thingiverse
free
RIFLE by leonk
...rifle by leonk
thingiverse
rifle
thingiverse
free
Rifle hanger
...rifle hanger
thingiverse
simple 1 hole rifle hanger
thingiverse
free
95th Rifles
...95th rifles
thingiverse
95th rifle napoleonic war soldiers.
thingiverse
free
Repeater rifle
...repeater rifle
thingiverse
one repeater rifle for your legoheim warband.
thingiverse
free
Sniper's rifle / rifle de francotirador by reneujo
...al sniper rifle, one meter long, designed and manufactured for a military costume, incorporating all the details of a real rifle.
thingiverse
free
Rifle Hooks
...ngiverse
made simple rifle hooks. plan to hang up my airsoft guns but should work on any real/fake rifle that isn't too wide
thingiverse
free
Rifle Stand
...le or a shotgun.
i used ~60cm threaded rods - it's enough for most rifles.
using 3 rods will increase stability of the stand.
thingiverse
free
M16 RIFLE by leonk
...m16 rifle by leonk
thingiverse
m16 rifle
thingiverse
free
Bullpup Rifle by Tmanzz122
...bullpup rifle by tmanzz122
thingiverse
rifle with stand
Cap
thingiverse
free
CAP
...cap
thingiverse
cap antenna base
thingiverse
free
1" Cap cap by Doz1971
...1" cap cap by doz1971
thingiverse
a cap to assist in re-stuffing electrolytic capacitor cans in vintage electronics.
thingiverse
free
TINKER CAP
...tinker cap
thingiverse
cap
thingiverse
free
caps by mjk2203
...caps by mjk2203
thingiverse
caps
thingiverse
free
cap by Artformer
...cap by artformer
thingiverse
cap
thingiverse
free
cap
...cap
thingiverse
9
thingiverse
free
Snapback Cap
...snapback cap
thingiverse
snapback cap, for different headsizes just scale the cap up or down.
thingiverse
free
capped by cheeba
...capped by cheeba
thingiverse
just a cap
thingiverse
free
RJ45 Cap
...rj45 cap
thingiverse
this is a rj45 cap
thingiverse
free
oil cap
...oil cap
thingiverse
oil cap