Shelf supports 5mm

...shelf jig by fragasaurus thingiverse shelf jig with 5mm holes. used for spacing shelf support holes.

...ple shelf support. peg measured at 5mm, a light bit of filing might be needed. supports not required with the peg on the plate.

...shelf clip for merillat cabinets thingiverse replacement shelf clip for merillat cabinets with 5mm holes. print with supports.

...electric cable support for ikea furniture thingiverse clip that fits into the shelf holes of ikea furniture (5mm).

...into the 5mm holes. the tab at the end is to allow them to be gripped with pliers to pull them out of the sides of the bookcase.

... 5mm by tattooed1980 thingiverse a simple pin because i broke mine :) optimized for maximal strongness and print without support

...mão francesa (clamp/support shelf) by acamedeiros thingiverse intern hole is 5mm print with at least 3 outline and 30% infill.

...f height. maybe not the most lightweight or elegant method, but it works and is stable. i used petg with 2 shells and 25% infill.

...m in my kitchen! let me know how you are getting on! no support needed, print time approx. 18 minutes with 0.2mm and 100 % infill

...shelf peg by grim8819 thingiverse a simple shelf peg for a 5mm hole.

...router shelf. just a shelf ))) by kormag thingiverse router, wifi, shelf

... 10 assuming tensile yield at 50mpa. the bracket requires 2x m4 countersunk (ctsk flat - din en iso 7046-1) screws for mounting

...f thingiverse this is a shelf and key organizer. width: 80mm length: 60mm. link to my website: https://quinten3d.simplesite.com/

...shelf by bcsprayer thingiverse shelf

...shelf by costa_d thingiverse shelf

...shelf by maxfm thingiverse a shelf

...shelf by 3dform thingiverse shelf

...shelf by doesliverpool thingiverse shelf

...shelf by themaker132 thingiverse a shelf

...shelf riser thingiverse shelf riser

...to 5mm connector by szczepko thingiverse it presents a designed 5mm by 5mm connector length 30mm 4 2mm holes for locking screws.

... to 5mm for stepper motor by mrakuaku thingiverse this is a small coupler i made. it uses 3m nuts and bolts and fits 5mm to 5mm.

...5mm spacer by boutrous thingiverse 5mm spacer

...circle 5mm by jovack669 thingiverse it's lots of circles going up in 5mm from 5mm to 50mm sizes.

...verted to a 5mm by okatake thingiverse it is the coupling to convert to the shaft axis of a shaft stepper motors 5mm to 5mm/6mm.

...2020 5mm by tazzi911 thingiverse abdeckung für 2020 5mm profil

...knob 5mm by innovativeuser thingiverse round knob for furniture with a 5mm hole

...hex key 5mm thingiverse hex key. 5mm based on my drumkey.

...bb 5mm by elit33 thingiverse 5mm bb/pellet (use supports for 5)

...support filament support by capucinois thingiverse simple filament support / un support simple pour filament

...support rasoir thingiverse support for shaver support pour rasoir

...y zedeau thingiverse support for honor 8 with a support for a car with a coin holder like this onehttp://i.imgur.com/belww0z.jpg

...a corresponding track on the conservatory then standard cutter supports drop into the recess on this...

...support by leonk thingiverse support

...support by leonk thingiverse support

...support by leonk thingiverse support

...support by leonk thingiverse support

...support by leonk thingiverse support

...shaver support thingiverse support