Similar models
thingiverse
free
Adapter servo mount to 3/16 hex wrench bit. by Lanctot
...ex wrench bit. by lanctot
thingiverse
this adapter can be mounted on top of the servo to to convert to a 3/16 allen wrench bit.
thingiverse
free
Turnigy 380mg servo holder for rcexplorer tricopter tilt by TeeSCee
... mount. i made the top gap on the mount a bit wider and then made all the "walls" a bit thicker to compensate for that.
thingiverse
free
Servo Holder 41mm - OpenRC Truggy by Bitfrost
... by bitfrost
thingiverse
it´s a servo holder, 41mm (standard servo size) for openrc truggy.
its a bit greater than the original.
thingiverse
free
Gitup F1 holder for servo mount
...and dont have splines, but heat it a bit and push it on the horn and fix it with a screw
one for standard servo and one for minis
thingiverse
free
Servo Mount DF-4S by lothar6472
...d in the df models df-4s.
the design is a set a bit backwards to give the servo more spave for movement by action in suspensions.
thingiverse
free
Makeblock Servo Mount M4 Screws by oserobots
...thingiverse
makeblock mount using m4 screws
this is made to us a bit of plastic to create a mount for a servo on your makeblock.
thingiverse
free
Nema 42mm Servo plate by Tattoopyramidhd
...olt circle as the servo. i also added one with a 22mm center hole, it should fit fine but might be a bit snug on the center boss.
thingiverse
free
Durafly Slowpoke Servo Cover
...r planes as well.
i print it in abs (for a bit of uv resistance), 0.2mm layers, 4 layers top/bottom, 3 perimeters and 75% infill.
thingiverse
free
Alt servo pulley for InMoov hand servos. by kwatters
... these mount directly on the servo gear. i recommend printing them out with a higher infill (50%) to make them a bit more solid.
thingiverse
free
Right Servo mount for the "speedy Red Swept wing RC" by _Dave
...micro servo 9 gram
this servo is taller and wider than the hitec hs-55 and quite a bit shorter than the hobby king turnigy servo.
Enginsubasi
thingiverse
free
Plastic Pipe Filter v2 by enginsubasi
...plastic pipe filter v2 by enginsubasi
thingiverse
plastic pipe filter v2
thingiverse
free
Plastic Pipe Filter v1 by enginsubasi
...plastic pipe filter v1 by enginsubasi
thingiverse
this filter is using for water plastic pipe.
thingiverse
free
RC Servo 9g Holder by enginsubasi
...rc servo 9g holder by enginsubasi
thingiverse
to mount 9g rc servo
holes m3
Servo
thingiverse
free
Servo to Servo by MrBancroft
...servo to servo by mrbancroft
thingiverse
servo-to-servo connector
thingiverse
free
Servo to Servo idle by Hackens
...servo to servo idle by hackens
thingiverse
plug a servo to another servo
thingiverse
free
Servo Retainer 9g servos by husrto75
...thingiverse
this is a small servo retainer for 9g servos. the little ones that come with servos are terrible.
i used a 80% fill.
thingiverse
free
Servo mount for 9g Servo. by spycatcher2k
... spycatcher2k
thingiverse
servo mount for proto-pic servo , part number ppservo1 : http://proto-pic.co.uk/analogue-9-gram-servo/
thingiverse
free
Aero Servo Mount 9G servo
...aero servo mount 9g servo
thingiverse
aero cover for a 9g servo
thingiverse
free
Servo Case
... servo case for a olimex servo. specifically the ms- 1.3-9. just a protective case for the outside of the servo. print at 50mm/s.
thingiverse
free
Servo MG996
...servo mg996
thingiverse
servo mg996
thingiverse
free
servo lock
...servo lock
thingiverse
servo lock
thingiverse
free
Ghetto servo mount (micro servo) by condac
...vo mount (micro servo) by condac
thingiverse
servo mount for micro servo to use cable tie to mount a micro servo where you want.
thingiverse
free
Servo Mount for 9gr servo by odie_wan
...r structure. this allows the servo to be removed so you can change the servo arm without gluing/regluing or mangling you vehicle.
Bits
thingiverse
free
Bit holder for 6.4mm bits by Hustensaft
...bit holder for 6.4mm bits by hustensaft
thingiverse
jet another bit holder for the typical 6.4mm bits.
thingiverse
free
Bit Holder
...bit holder thingiverse bit holder for drill bits ...
thingiverse
free
Bit Container - Bit Holder by XrControl
...container - bit holder by xrcontrol
thingiverse
bit container - bit holder
youtube: xrcontrol
www.xrcontrol.de
noc0815@gmail.com
thingiverse
free
Chiave bits - Wrench bits
...y tight places.
chiave utilizzata in accoppiata con i bits dell'avvitatore per permettere di raggiungere posti molto angusti.
thingiverse
free
Bit holder for 10 bits by StijnDS
... 10 bits by stijnds
thingiverse
first try to make a screw bit holder
the bits still fall out. i would like the to fit perfectly.
thingiverse
free
bit holder
...that can attached to 2nd bit holder for 4 bits . v4 for different type of bit and 1...
thingiverse
free
BIT CASE
...bit case
thingiverse
bit case
thingiverse
free
Bit Screwdriver
...bit screwdriver thingiverse bits holder/...
thingiverse
free
Bit holder
...bit holder thingiverse hold tool bits ...
thingiverse
free
Bit Holder
...bit holder
thingiverse
drilling machine bit holder