Servo Cover by skyraccoon

...servo to servo by mrbancroft thingiverse servo-to-servo connector

...servo to servo idle by hackens thingiverse plug a servo to another servo

...thingiverse this is a small servo retainer for 9g servos. the little ones that come with servos are terrible. i used a 80% fill.

...vo mount (micro servo) by condac thingiverse servo mount for micro servo to use cable tie to mount a micro servo where you want.

... spycatcher2k thingiverse servo mount for proto-pic servo , part number ppservo1 : http://proto-pic.co.uk/analogue-9-gram-servo/

...pi camera to servo mount by dominic_c thingiverse this print allows you to mount an rpi camera on servos. (and servos on servos)

...ervo protector by habendanio thingiverse these protect the servo arms. 2 sizes. one for micro servos and the other for 9g servos

...servo mount for a hitec hs-5085mg servo by urw thingiverse this a vertical servo mount for a hitec hs-5085mg servo

...servo bracket. by r91wrd thingiverse servo bracket for standard servo size.

...servo adapter by mosteveo thingiverse servo adapter for heli tail servo

...100x60mm servo cover by skyraccoon thingiverse simple 60x100 servo cover. print in pla, no support needed

...he servo cover is 60x60 but the protusive part is 50x50mmx6mm the tunnel is 12mm wide and 7mm height (so it's 13mm in total).

...e frame and then slide the clips on the sides. finally screw. use m2 screws. if you have flat head screws it will be even better.

..., while the other ones do fit the outside of the cap (see picture). the cap is printed in tpu while the icons are printed in pla.

...v6 40mm fan adapter by skyraccoon thingiverse e3d v6 40mm fan adapter. petg is probably best but i did it in pla without problem

...e. tried to do the smallest footprint possible, weight is 2.5 g. the screw is really optionnal, it should work without any screw.

...m magnets, i know it's a little bit large for such a small box, but it was the only ones i had :) and finally it works great.

...result :https://youtu.be/bp2us8chzhu don't try to place real tea light in this... never tried myself but probably a bad idea.

...l a big hole in the fuselage, this one can simply be taped with a double face tape. (you can also print in pla but tpu is better)

...servo to servo by mrbancroft thingiverse servo-to-servo connector

...servo to servo idle by hackens thingiverse plug a servo to another servo

...thingiverse this is a small servo retainer for 9g servos. the little ones that come with servos are terrible. i used a 80% fill.

... spycatcher2k thingiverse servo mount for proto-pic servo , part number ppservo1 : http://proto-pic.co.uk/analogue-9-gram-servo/

...aero servo mount 9g servo thingiverse aero cover for a 9g servo

... servo case for a olimex servo. specifically the ms- 1.3-9. just a protective case for the outside of the servo. print at 50mm/s.

...servo mg996 thingiverse servo mg996

...servo lock thingiverse servo lock

...vo mount (micro servo) by condac thingiverse servo mount for micro servo to use cable tie to mount a micro servo where you want.

...r structure. this allows the servo to be removed so you can change the servo arm without gluing/regluing or mangling you vehicle.

...doorbell cover thingiverse this is a doorbell cover created to replace an damaged cover.

...cover r thingiverse cover

...ipad2018 cover thingiverse cover

...cover by tlatmemad thingiverse cover

...cover by hrii3y thingiverse just cover for cover something, u can change dimmensions at slicer

...toothbrush cover thingiverse toothbrush cover

...webcam cover thingiverse webcam cover

...cover by chris_skywalker thingiverse this is a cover of a box

...cover by kindafluffy thingiverse cover led

...cover by wolfetter thingiverse cover for drill