Thingiverse
Semi Ducted Micro Frame (Beecheese Frame) by Noctaro
by Thingiverse
Last crawled date: 4 years, 5 months ago
This is a remix of stylesuxx's great ducted micro cheeseframe.
I made this after testing his frame wich blew me away. A few hours later i was ordering a slight bigger flightcontrol board wich did not fit the cheeseframe.
I made the walls even thicker - 1.2mm seems to be perfect rigid for this case.
The ducts have less but bigger holes, this might decrease the disturbance wind causes on ducted frames even further.
This frame has a low profile between the ducts and should generate nearly no air resistance.
Print it with 100% infill. You can print it pretty fast with still good results.
It will fit 8520 motors and 50mm props.
Do not forget to break in your motors. (Around 1 lipo pack at min throttle, best way to do is on motors tab in betaflight configurator)
(Links to banggood)
Flight control board:
Omnibus F3 with OSD and RXhttps://goo.gl/iPsMra
Motors Racestar 8520https://goo.gl/8DxBGM
Propellers 3 Bladehttps://goo.gl/nEud0F
FPV Camhttps://goo.gl/aqRcHs
Lipo battery 650mah 25 C including USB charger (higher C rate means more power for your quad)https://goo.gl/VwDGNw
Further you need:
Transmitter of your choice. I use this one -> https://goo.gl/GwRqK4
FPV goggle of your choice. I use this one -> https://goo.gl/1OyqmI
(Links to Hobby King)
4x JST SH 1.0 - 2 Pin - pigtails or connectors for the motors -> https://goo.gl/h1MypS
1x JST SH 1.0 - 4 Pin - pigtails or connectors for the fpv camera -> https://goo.gl/F8oXKn
Build video: (english subtitles)https://youtu.be/LPq8Mr7HCQQ
Inflight footage:https://www.youtube.com/watch?v=UjmH5yw2Oa4https://www.youtube.com/watch?v=HFpl1kW11cEhttps://www.youtube.com/watch?v=lvVpgYhq9Pw
Print Settings
Printer Brand:
Printrbot
Printer:
Printrbot Plus
Rafts:
No
Supports:
No
Resolution:
0.2
Infill:
100%
I made this after testing his frame wich blew me away. A few hours later i was ordering a slight bigger flightcontrol board wich did not fit the cheeseframe.
I made the walls even thicker - 1.2mm seems to be perfect rigid for this case.
The ducts have less but bigger holes, this might decrease the disturbance wind causes on ducted frames even further.
This frame has a low profile between the ducts and should generate nearly no air resistance.
Print it with 100% infill. You can print it pretty fast with still good results.
It will fit 8520 motors and 50mm props.
Do not forget to break in your motors. (Around 1 lipo pack at min throttle, best way to do is on motors tab in betaflight configurator)
(Links to banggood)
Flight control board:
Omnibus F3 with OSD and RXhttps://goo.gl/iPsMra
Motors Racestar 8520https://goo.gl/8DxBGM
Propellers 3 Bladehttps://goo.gl/nEud0F
FPV Camhttps://goo.gl/aqRcHs
Lipo battery 650mah 25 C including USB charger (higher C rate means more power for your quad)https://goo.gl/VwDGNw
Further you need:
Transmitter of your choice. I use this one -> https://goo.gl/GwRqK4
FPV goggle of your choice. I use this one -> https://goo.gl/1OyqmI
(Links to Hobby King)
4x JST SH 1.0 - 2 Pin - pigtails or connectors for the motors -> https://goo.gl/h1MypS
1x JST SH 1.0 - 4 Pin - pigtails or connectors for the fpv camera -> https://goo.gl/F8oXKn
Build video: (english subtitles)https://youtu.be/LPq8Mr7HCQQ
Inflight footage:https://www.youtube.com/watch?v=UjmH5yw2Oa4https://www.youtube.com/watch?v=HFpl1kW11cEhttps://www.youtube.com/watch?v=lvVpgYhq9Pw
Print Settings
Printer Brand:
Printrbot
Printer:
Printrbot Plus
Rafts:
No
Supports:
No
Resolution:
0.2
Infill:
100%