Thingiverse
Segway Minipro Control Bar by goodinga
by Thingiverse
Last crawled date: 3 years ago
This handle replaces the knee control of the Segway Mini-Pro. I live in a rural environment with gravel and dirt roads, and need more control than the knee bar offers. I rode the original Segway, and liked it's handle bar control system. I believe the Mini-Pro has a more delicate control arm construction and this new control bar was constructed to not over stress the original control mechanism.
This arm achieves 4 objectives:
Better control than the original.
Balances like the original.
Built in stand.
Built in MiniPro carry handle.
It is also lighter, locks in place and is as easy to remove.
Non-printing materials needed are 3' of 1/2" aluminum rod and 7" of 3/8" aluminum rod or similar.
The top knob is small, meant for gripping with 2 fingers. It doesn't need much side to side force to steer. Forward and reverse are handled by balance as before. I think the paddle handle works best.
The plastic fitting needs to be strong, so it is printed with no fill except for 30% on the bottom plate. The rest is 6 top, 6 bottom and 6 perimeter layers. I printed in ABS, then brushed it with acetone, then 2 hours in an acetone fume chamber to fully bond the layers and produce a glossy finish. There are 2 drain holes in the inside, fill up between the inner and outer wall, then drain. It will cure overnite.
The lock is made with a bit of 1/8" thick or less flat bar bent 90 degrees, drilled and secured with a flat head 3mm bolt screwed from the inside, thru the lock, thru a small spring, secured with a nut and washer. See photo.
Print a 1" test section to check for fit on the MiniPro. I printed at 90% extrusion rate, 2400 feet per minute, sitting on the bottom plate. Cooling was 10% fan after the bottom plate.
The aluminum rods can be threaded or glued. I threaded mine, 1/2-13. The 7" rod is for the handle / stand. The control bar hole will need to be altered or drilled to 1/2" if glued.
The little Tee handle is for the original control bar, as mine broke on first use and I needed something stronger. It is not needed otherwise.
This arm achieves 4 objectives:
Better control than the original.
Balances like the original.
Built in stand.
Built in MiniPro carry handle.
It is also lighter, locks in place and is as easy to remove.
Non-printing materials needed are 3' of 1/2" aluminum rod and 7" of 3/8" aluminum rod or similar.
The top knob is small, meant for gripping with 2 fingers. It doesn't need much side to side force to steer. Forward and reverse are handled by balance as before. I think the paddle handle works best.
The plastic fitting needs to be strong, so it is printed with no fill except for 30% on the bottom plate. The rest is 6 top, 6 bottom and 6 perimeter layers. I printed in ABS, then brushed it with acetone, then 2 hours in an acetone fume chamber to fully bond the layers and produce a glossy finish. There are 2 drain holes in the inside, fill up between the inner and outer wall, then drain. It will cure overnite.
The lock is made with a bit of 1/8" thick or less flat bar bent 90 degrees, drilled and secured with a flat head 3mm bolt screwed from the inside, thru the lock, thru a small spring, secured with a nut and washer. See photo.
Print a 1" test section to check for fit on the MiniPro. I printed at 90% extrusion rate, 2400 feet per minute, sitting on the bottom plate. Cooling was 10% fan after the bottom plate.
The aluminum rods can be threaded or glued. I threaded mine, 1/2-13. The 7" rod is for the handle / stand. The control bar hole will need to be altered or drilled to 1/2" if glued.
The little Tee handle is for the original control bar, as mine broke on first use and I needed something stronger. It is not needed otherwise.
Similar models
thingiverse
free
Segway MiniPro handle with broom threads by Qskool
...ned thing and added threads for a generic broom handle. this part inserts into the "walking arm" of the segway minipro.
thingiverse
free
SegWay MiniPro Wheel Blade by cjkturtle
...pro wheel blade by cjkturtle
thingiverse
a replacement part for your segway minipro. just print and slide in like the real part.
thingiverse
free
1/2" Farro Rod Handle & Belt Clip
...andle and belt clip for a 1/2" farro rod. after printing, you need to epoxy the rod into the handle in order for it to work.
thingiverse
free
Toolmakers Clamp by kedalton
...d ends will also need to be glued or epoxied on to the ends of the threaded rods. see the photos for detailed assembly drawings.
thingiverse
free
2pc monitor control door with lock together for easy gluing by jocan
... and added a lock tab with guide plate for easy centering and gluing. printed with pla on ender 3. thanks to original designer!
thingiverse
free
beam compass by bobcap1957
...elf. i used supports "touching build plate" and a "raft" because of how the screw prints.
hope you enjoy it!
thingiverse
free
Barn door handle by animuL67
... the pull plate sits flush so no need to route a pocket into the door. use 3" long wood screws for a 1-3/8" thick door.
thingiverse
free
Fireball 1L Bottle Prison
...; nuts)
for a full printed design (no need for threaded rods) check out:https://www.thingiverse.com/thing:3503905
(not my design)
thingiverse
free
CP33 Telescoping Tailhook adapter
...n wrench shaft locks into small groves that you cut into the aluminum rods. i recommend a dremel with a cutting wheel to do this.
thingiverse
free
00 scale 7 foot wide canal lock by divingjgb
...lock gates should be made from some 2mm wire rod.
the boat in the photos is a 00 scale 70' long narrow boat (not 3d printed).
Goodinga
thingiverse
free
Doorstop by goodinga
...his one has the step sloped so it comes level when pushed under the door. i included the openscad code so it could be modified.
thingiverse
free
Tarp Clamp by goodinga
...ess of the opening is adjustable.
the thumb rest allows you to easily control the clamp opening with one hand, no spring needed.
thingiverse
free
Rope Thimble by goodinga
...ut a frame on the throat of the thimble for printing and used rafting, then used a bandsaw to remove it.
arthurgooding@gmail.com
thingiverse
free
Parametric Rope Thimble by goodinga
...ing for these layers only. if using abs, finish with acetone vapour bath to improve layer bonding, strength and surface finish.
thingiverse
free
Pocket Lantern by goodinga
...y needed for the panel indent on the lid. i printed 5 top layers, 3 side and bottom layers, 30% infill. it is a good solid box.
thingiverse
free
Macbook Pro Holder, Macbook Air Holder, Computer Holder by goodinga
...s good. the macbook pro slot width as designed is 18.2mm, change scale for any other computer. the macbook air slotwidth is 12mm.
thingiverse
free
iPadAir iPadAir2 iPadPro grip and bumpers by goodinga
... from wandering onto the screen.
if you need an ipadair grip, scale the .stl file. the ipadair2 is 6.1mm thick. the air is 7.6mm.
thingiverse
free
Tarp Gripper all printed
...printed thingiverse remix of the excellent tarp clip by goodinga changes: all parts are printed, no external bolts or...
Minipro
thingiverse
free
miniPRO Dyno Electronic Board Cover by minipro
... dyno.
part no. 08090001md101 = version 1.0
part no. 08090001md102 = version 2.0
p.s. part no is located below the reset button
thingiverse
free
SegWay MiniPro Wheel Blade by cjkturtle
...pro wheel blade by cjkturtle
thingiverse
a replacement part for your segway minipro. just print and slide in like the real part.
thingiverse
free
Segway MiniPro handle with broom threads by Qskool
...ned thing and added threads for a generic broom handle. this part inserts into the "walking arm" of the segway minipro.
thingiverse
free
Ninebot MiniPro Street handlebar mount with an adapter for a Cell Phone Holder by joschi2009
...apter for a cell phone holder by joschi2009
thingiverse
this is a remake of the ninebot minipro street handlebar mount by jann_h
thingiverse
free
Ninebot MiniPro Street handlebar mount by JanN_H
...r as handlebar.the endplugs have a gap to clamp the end of wrapping tape. the holes are for cutting a m6 thread to take m6 bolts.
cg_trader
$49
Ninebot by Segway Minipro
...s created on real base. it’s created accurately, in real units of measurement, qualitatively and maximally close to the original.
grabcad
free
Achse für Ninebot MiniPro
...teil zu bestellen.
aber das löst ja nicht das problem der falschen materialwahl. ich empfehle flugzeugalluminium oder edelstahl.
grabcad
free
Igernet LoRa-Node-Minipro-RFM95
...addition to that board a low-power-timer board is currently in development. after finished that board will also be uploaded here.
grabcad
free
10 inch Hoverboard Motor
...10 inch tires motor used on hoverboards and ninebot minipro ...
Segway
3ddd
$1
Segway
...segway
3ddd
segway
без модификаторов
turbosquid
$1
SEGWAY
...y free 3d model segway for download as max, 3ds, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1672587)
turbosquid
$48
Segway
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
archive3d
free
Segway 3D Model
...chive3d
segway equipment
segway n140109 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$35
Segway hoverboard
... segway hoverboard for download as ma, max, c4d, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1697478)
3d_export
$49
Segway I2 3D Model
...ecologic electric eco city transport future scooter green scifi mobile segway i2 x2 urban
segway i2 3d model squir 79706 3dexport
3d_export
$49
Segway X2 3D Model
...ecologic electric eco city transport future scooter green scifi mobile segway i2 x2 urban
segway x2 3d model squir 79796 3dexport
cg_studio
$49
Segway X23d model
...gstudio
.3ds .c4d .fbx .lwo .max .mb .obj - segway x2 3d model, royalty free license available, instant download after purchase.
turbosquid
$40
Segway S-Pod
... 3d model segway s-pod for download as max, max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1564838)
3d_export
$12
electric scooter ninebot by segway
...scooter ninebot by segway
3dexport
electrical segway 3d model<br>formats: .max - .3ds - .obj - .fbx<br>with textures
Control
3d_ocean
$4
Controller TQFP32
...qfp32
3docean
chip controller cpu electronic gpu mcu micro controller silicon smd tqfp wafer
a micro controller in tqfp32 package
3d_ocean
$4
Controller TQFP44
...44
3docean
chip controller cpu electronic gpu mcu micro controller package smd tqfp tqfp44
a micro controller in a tqfp44 package
3d_export
$15
control unit
...control unit
3dexport
control unit
3ddd
$1
Yacht control
...yacht control
3ddd
yacht control
3d_export
$5
controle pgdm
...controle pgdm
3dexport
carcaca controle pgdm
turbosquid
free
controler
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Control
...
http://www.schmitz-leuchten.de/html-ru/einzelleuchten-lampentyp-details.php?lamptype_no=700&group;=917&id;=731
3d_ocean
$4
Controller TQFP100
...100
3docean
chip computer cpu electronic gpu mcu micro controller pin platine silicon wafer
a micro controller in tqfp100 package
3d_ocean
$4
Controller TQFP64
...qfp64
3docean
chip computer cpu gpu mcu micro controller package silicon tqfp tqfp64 wafer
a micro controller in a tqfp64 package
3d_ocean
$7
Remote controller
... control switcher tv remote
remote controller for tv, sound systems etc easy to edit textures photo real rendered with mental ray
Bar
archibase_planet
free
Bar
...bar
archibase planet
bar bar rack
bar 2 - 3d model for interior 3d visualization.
archibase_planet
free
Bars
...bars
archibase planet
horizontal bar parallel bars
parallel bars - 3d model for interior 3d visualization.
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar