Similar models
thingiverse
free
Seedling Raising Kit by scooperboy
... for a living.
i printed with 3 bottom layers, 2 shells and 4 top solid layers. i'm sure it would be fine with 2 all around.
thingiverse
free
Tomato seedling support cage by abessetti
...tomato seedling support cage by abessetti
thingiverse
tomato seedling support cage
thingiverse
free
Seedling guide cage for tomatoes by abessetti
...seedling guide cage for tomatoes by abessetti
thingiverse
seedling guide cage for tomatoes
thingiverse
free
Seedling starters (for Window Greenhouse) by _Mari_Makes_
...e seedling starters. one design is for the ikea vaxxer steelwoolplugs, the other is for disc cocoplugs. the prints can be reused.
thingiverse
free
Seedling Pot by tim36272
...seedling pot by tim36272
thingiverse
a small seedling pot with removable floor (for getting the plant out).
thingiverse
free
ThinkFun Battle Protectors by Southwest145
... / wing protector goes on the side of you thinkfun kit and the two front cone like protectors go on the front of you thinkfun kit
thingiverse
free
ThinkFun Battle Protectors by Southwest145
.../ wing protector goes on the side of you thinkfun kit and the two front cone like protectors go on the front of you thinkfun kit.
thingiverse
free
Parametric Seedling Tray Bracket by kelchm
...rametric seedling tray bracket by kelchm
thingiverse
this is a parametric bracket designed to hold koram 12 cell seedling trays.
thingiverse
free
custumizable seedling cup holder. by florpglorp
...l rolls. it can also be used as standalone seedling trays.
inner diameter and number of cups (rows and columns are customizable)
thingiverse
free
Martian II motor protector by macabox
...ector by macabox
thingiverse
new motor protector for my martian ii ... please if you want print it and test the motor protector.
Trampi
thingiverse
free
Big Soil Block Press by trampi
...ver the block
you will need a jar (or something with these size) to drive the press and release the block. any item in your house
thingiverse
free
Soil Block maker for cuts and propagation by trampi
... in a cold place, maybe you want to buy a heat mat and place under the tupperware
you can use rooting gel to get faster results.
thingiverse
free
Micro water cannon for aero cloning machine by trampi
...re water and less pression = don´t work good.
so it´s better to do a very little hole and try , instead that one bigger and fail
Seedlings
thingiverse
free
Seedling Pot by tim36272
...seedling pot by tim36272
thingiverse
a small seedling pot with removable floor (for getting the plant out).
thingiverse
free
Seedling planter
...seedling planter
thingiverse
use vase mode / spiralize outer contour
thingiverse
free
Seedling Pot
...the center.
step 5:
fill it up to the mark and water it. place it where it gets a lot of light and the temperatures are moderate.
thingiverse
free
Seedling Supporter by JMecky
...ring at an angle. sharp ends stick in dirt.
enjoy!
2 sizes.
1.5 inch tall qty:1 or qty:10
3 inch tall qty: 1 or qty:10
thingiverse
free
Seedling Raising Kit by scooperboy
...out bottom to make it easier to remove the seedlings the seedling tray insert holds the pots and allows...
thingiverse
free
Seedling Planter by 23046295
...seedling planter with 10 mm drainage holes. print upside down with supports. i reduced mine to 90% scale to fit the printing bed.
thingiverse
free
Tomato seedling support cage by abessetti
...tomato seedling support cage by abessetti
thingiverse
tomato seedling support cage
thingiverse
free
Seedling guide cage for tomatoes by abessetti
...seedling guide cage for tomatoes by abessetti
thingiverse
seedling guide cage for tomatoes
thingiverse
free
Seedling tray by SuperGee
... 45mm
the v2 insert piece can be used on the v1 tray. increase the size to 105.5% before printing. do not change the orientation.
Protector
thingiverse
free
corner protector
...corner protector
thingiverse
corner protector
thingiverse
free
Athletic protector
...athletic protector
thingiverse
athletic protector
;-)
thingiverse
free
Protector culata
...protector culata
thingiverse
protector culata motor
thingiverse
free
Protector de Enchufe/ Power Plug Protector by mrozas
...protector de enchufe/ power plug protector by mrozas
thingiverse
protector para enchuge 220v
thingiverse
free
Cogmind - Protector by SharkPrints
...cogmind - protector by sharkprints
thingiverse
protector
thingiverse
free
T16 protector
...t16 protector
thingiverse
i quickly made a gimbal protector that extend to all the switches. printed in tpu.
thingiverse
free
Taranis stick protector by th3code
...ngiverse
taranis stick protector
taranis stick protector
taranis stick protector
taranis stick protector
taranis stick protector
thingiverse
free
ms50 protector by squowse
...ms50 protector by squowse
thingiverse
ms50 protector
thingiverse
free
Drone Motor Protector
...drone motor protector
thingiverse
motor protector
thingiverse
free
Coronavirus protector by Oscar3Dr
...coronavirus protector by oscar3dr
thingiverse
coronavirus protector