Thingiverse
![Sandblasting gun by Rick4003](/previews/8348654.jpg)
Sandblasting gun by Rick4003
by Thingiverse
Last crawled date: 3 years, 2 months ago
Blasting gun to replace standard gun on table top blasting cabinet. I believe it would also fit the standard floor type Harbour Freight Chinese cabinet.
A foot pedal is recommended although i just connected and disconnected the air hose in use.
The blasting gun uses the same ceramic nozzle as the standard gun. The air nozzle I made out of a piece of m10 threaded rod with a hole drilled through. The diameter of the air hole should be adjusted according to compressor size. I drilled mine at 3.5mm and my 5.5Hp compressor can hardly keep up. A 2-2.5mm nozzle would likely be suitable.
The M10 thread is cut into the gun using a tap.
Hose connection is 12mm
The printed nut didn't fit directly of the printer so I tried the original aluminium nut and this fitted perfectly.
It was meant as a test of the design before I turned and welded one up of aluminium but it works so well that I just decided to print a new one when it wears out. So far it have held up well.
I have only tested it with glass beads so far, but the performance of the blasting cabinet have increased dramatically! Removal of paint and rust have increased by more than fivefold. Now I can hardly move the parts quick enough to keep up with the gun. And this is even with reduced pressure.
Prepare to unleash the potential of your blasting cabinet!
A few other mods have also been done to the cabinet to mimic the mixing chamber as more professionel units have. Pictures will follow.
A foot pedal is recommended although i just connected and disconnected the air hose in use.
The blasting gun uses the same ceramic nozzle as the standard gun. The air nozzle I made out of a piece of m10 threaded rod with a hole drilled through. The diameter of the air hole should be adjusted according to compressor size. I drilled mine at 3.5mm and my 5.5Hp compressor can hardly keep up. A 2-2.5mm nozzle would likely be suitable.
The M10 thread is cut into the gun using a tap.
Hose connection is 12mm
The printed nut didn't fit directly of the printer so I tried the original aluminium nut and this fitted perfectly.
It was meant as a test of the design before I turned and welded one up of aluminium but it works so well that I just decided to print a new one when it wears out. So far it have held up well.
I have only tested it with glass beads so far, but the performance of the blasting cabinet have increased dramatically! Removal of paint and rust have increased by more than fivefold. Now I can hardly move the parts quick enough to keep up with the gun. And this is even with reduced pressure.
Prepare to unleash the potential of your blasting cabinet!
A few other mods have also been done to the cabinet to mimic the mixing chamber as more professionel units have. Pictures will follow.
Similar models
thingiverse
free
![Air compressor, hose connection. Male&Female](/t/4977832.jpg)
Air compressor, hose connection. Male&Female
... my compressor can run up to 12 bar so the connection must fit properly.
just print (<0.1) and continue sanding until it fits.
thingiverse
free
![M10 Barb hose fitting by superdave42](/t/8863987.jpg)
M10 Barb hose fitting by superdave42
... it did not put a force on this fitting when it was warm, used it for 3 days in a row so far no leaks.
use at your own risk :-)
thingiverse
free
![Z Rib for CR10 by TarantulaTevo](/t/8552154.jpg)
Z Rib for CR10 by TarantulaTevo
...ts
4x m10 washers
8 t-nuts
8 screws, that fit your t-nuts.
i used m5 t nuts and 10mm m5 schrews with countersunk head
have fun :)
thingiverse
free
![Ryobi air compressor side cover by Gigante](/t/8276170.jpg)
Ryobi air compressor side cover by Gigante
...t it a bit to the side if you want to drill a hole in it for the hose.
print solid, and as the picture to make the clip stronger.
thingiverse
free
![7000wm laser air assist by CaptHowdy126](/t/10252337.jpg)
7000wm laser air assist by CaptHowdy126
...n mine so if u want u could increase its size by scaling it up by a few % an that might make it a little easier to get on an off.
thingiverse
free
![Air Nozzle 1/8 inch NPT Thread by AlthoffWoodshop](/t/8277703.jpg)
Air Nozzle 1/8 inch NPT Thread by AlthoffWoodshop
... my knuckle duster so i made a new one and printed it.
the threaded ends fit perfectly in a knuckle duster for an air compressor.
thingiverse
free
![Nozzle Organizer by AdamsLab](/t/8741498.jpg)
Nozzle Organizer by AdamsLab
...ap set.
i also uploaded the .stl in the wrong orientation. you'll want to print it with the holes facing up for best results!
thingiverse
free
![pool pump covers for closing by phatfly](/t/8251714.jpg)
pool pump covers for closing by phatfly
...imensions for a more precise solution.
i had gotten this idea from another thingiverse user through a comment thread. thank you!
thingiverse
free
![Air Assist Girdle for Laser Cutter Nozzle by Warren_3Deee](/t/9028008.jpg)
Air Assist Girdle for Laser Cutter Nozzle by Warren_3Deee
...nap fit it onto the nozzle before the abs had cooled and contracted completely.
now it "snaps" on and off quite nicely.
thingiverse
free
![CPAP OXY Nozzle by KVardeman](/t/8144822.jpg)
CPAP OXY Nozzle by KVardeman
...nozzle through the hose fitting drop it into the hole and push until nozzle base is flush with the back of the hose fitting wall.
Rick4003
thingiverse
free
![Vacuum Handle Id 35mm to Od32mm by Rick4003](/t/8364123.jpg)
Vacuum Handle Id 35mm to Od32mm by Rick4003
...ingiverse
vacuum hose adaptor from inside ø35 to outside ø32. suitable for older nilfisk vacuum handles. possibly other as well.
thingiverse
free
![Egg holder Siemens style by Rick4003](/t/9243644.jpg)
Egg holder Siemens style by Rick4003
...ace for 12 eggs in the original holders for the fridge, so i designed an extra egg holder in the same style as the original ones.
thingiverse
free
![Spoolholder support for m8 threaded rod by Rick4003](/t/8364110.jpg)
Spoolholder support for m8 threaded rod by Rick4003
... shape.
the stand is to meant to stand on top of the printer enclosure. i will upload a picture when the enclosure is completed.
thingiverse
free
![Artillery Sidewinder X1 Bed cable strain relief v4 late 2020 by Rick4003](/t/8008901.jpg)
Artillery Sidewinder X1 Bed cable strain relief v4 late 2020 by Rick4003
...letely. if the other three are wound all the way down without removing them, the bed can be lifted enough to install the bracket.
Sandblasting
thingiverse
free
![SANDBLASTER PARTS by BurgerAssman](/t/5025161.jpg)
SANDBLASTER PARTS by BurgerAssman
...sandblaster parts by burgerassman
thingiverse
parts for diy sandblaster
thingiverse
free
![Sandblaster v3](/t/4969849.jpg)
Sandblaster v3
...y supports at all.
hole size is made for m5 screw and nut on the other side.
if you are interested in my work. follow my profile.
thingiverse
free
![Accessories for DIY sandblaster cabinet by Scrachi](/t/8315577.jpg)
Accessories for DIY sandblaster cabinet by Scrachi
...s mount for sandblaster (i guess it's the right name for this...)
a switch box for controlling the fan and the cabinet light.
thingiverse
free
![Sandblaster window at USYD DMAF by oriface](/t/8691651.jpg)
Sandblaster window at USYD DMAF by oriface
...e
the laser cutting file to create the clear perspex window for the sandblaster used in the dmaf lab at usyd. 3mm clear perspex.
thingiverse
free
![Sandblast vacuum adapter by outcastrc](/t/8794849.jpg)
Sandblast vacuum adapter by outcastrc
...cuum.
the vacuum is too powerful as is so you'll also need to pick up a variable power switch to run the vacuum at 1/2 speed.
thingiverse
free
![Sandblast cabinet glove mount by ILLGotti](/t/8300655.jpg)
Sandblast cabinet glove mount by ILLGotti
...can find for it. if you use the standard sandblasting gloves that can be purchased at harbor freight, the...
thingiverse
free
![Sandblaster bottle cap by yuriy_syvakov](/t/8551966.jpg)
Sandblaster bottle cap by yuriy_syvakov
...ndblaster bottle cap by yuriy_syvakov
thingiverse
made for dust removing air blow gong from aliexpress. i used abs for printing.
thingiverse
free
![Remixed Sandblast vacuum adapter for Kaercher 35mm OD inlet by franky99](/t/8603474.jpg)
Remixed Sandblast vacuum adapter for Kaercher 35mm OD inlet by franky99
...st vacuum adapter for kaercher 35mm od inlet by franky99
thingiverse
sandblast adapter for kaercher 35mm odvacuum cleaner inlet.
thingiverse
free
![Sandblaster Nozzle by vSOAPYv](/t/8974551.jpg)
Sandblaster Nozzle by vSOAPYv
...ted about 40 minutes.
1-3/8" long
0.5" od
0.2" id
60 deg taper on top od.
fits a blaster purchased many years ago.
thingiverse
free
![Clarke Sandblast cabinet hose adapter for vacuum by chunky899](/t/10238005.jpg)
Clarke Sandblast cabinet hose adapter for vacuum by chunky899
...vacuum by chunky899 thingiverse i made this for our sandblasting cabinet at work. some monkey hung a high wattage...
Gun
thingiverse
free
![perfect gun bb gun](/t/4681329.jpg)
perfect gun bb gun
...b gun
https://youtu.be/vwju90sazmy
all new file (2020.01.23 00:23)
all new file (2020.01.23 00:23)
https://youtu.be/bd98b7pxffi
thingiverse
free
![Gun by nm081301](/t/8591400.jpg)
Gun by nm081301
...gun by nm081301
thingiverse
is gun
thingiverse
free
![guns by sergo1977](/t/8765023.jpg)
guns by sergo1977
...guns by sergo1977
thingiverse
guns
thingiverse
free
![gun by DDSW](/t/8634673.jpg)
gun by DDSW
...gun by ddsw
thingiverse
gun
thingiverse
free
![gun by DM_HuSane](/t/8876514.jpg)
gun by DM_HuSane
...gun by dm_husane
thingiverse
it is a gun
thingiverse
free
![GUN by yjh777](/t/8905873.jpg)
GUN by yjh777
...gun by yjh777
thingiverse
gun
thingiverse
free
![gun by happydead](/t/8854070.jpg)
gun by happydead
...gun by happydead
thingiverse
gun
thingiverse
free
![top,gun,war, mini gun by ezers](/t/8525066.jpg)
top,gun,war, mini gun by ezers
...top,gun,war, mini gun by ezers
thingiverse
top, gun, war, mini gun,
thingiverse
free
![Derringer gun stand - gun holder by Viktor_Tekula](/t/8089885.jpg)
Derringer gun stand - gun holder by Viktor_Tekula
...derringer gun stand - gun holder by viktor_tekula
thingiverse
stnad for gun cal. 45 derringer from great gun company.
thingiverse
free
![Derringer gun holder (gun stand) by Viktor_Tekula](/t/8089950.jpg)
Derringer gun holder (gun stand) by Viktor_Tekula
...a
thingiverse
this is gun holder for derringer cal. 45 from great gun company. very nice holder to exposure the gun n the shelf.