Thingiverse
![RKade Mini by DMRadford](/previews/8289665.jpg)
RKade Mini by DMRadford
by Thingiverse
Last crawled date: 3 years, 1 month ago
This handheld console runs a full sized Raspberry Pi (2, 3 or 3 B+) and gets 4-6 hours of battery life depending on which Pi you use, and which games you're playing.
Parts list:
Raspberry PiUSB JackBattery Charging CircuitAdafruit ItsyBitsy 32u4 - 5VPSP Joystick3v to 5v 3a Boost Converter2 Position Slide Switch18650 Batteries30 AWG wire
24 AWG wire (can use wire pulled from Ethernet cables)Proto Board PCB6mm Tactile Buttons
Micro USB cable to chop up.
Software:
Retropie 4.4juj fbcp-ili9341 SPI drivers
Wiring:
Spi Screen
Display--------Raspberry Pi
BL--------------pin 12 (GPIO 18)
SCK------------pin 23 (GPIO 11)
MISO----------pin 21 (GPIO 9)
MOSI----------pin 19 (GPIO 10)
CS--------------pin 24 (GPIO 8)
RST------------pin 22 (GPIO 25)
D/C-------------pin 18 (GPIO 24)
VIN-------------pin 17 (3.3v)
GND-----------pin 20 (GND)
Buttons
Shared ground across all buttons and joystick. Use extra protoboard pins to make all of the grounds common.
Buttons are wired to pins 0-13 and A2. Joystick axies are wired to A0 and A1.
Tricks:
I used electrical tape to hold the battery leads in place during assembly. The risers in the prints will apply the pressure needed to make contact.
Parts list:
Raspberry PiUSB JackBattery Charging CircuitAdafruit ItsyBitsy 32u4 - 5VPSP Joystick3v to 5v 3a Boost Converter2 Position Slide Switch18650 Batteries30 AWG wire
24 AWG wire (can use wire pulled from Ethernet cables)Proto Board PCB6mm Tactile Buttons
Micro USB cable to chop up.
Software:
Retropie 4.4juj fbcp-ili9341 SPI drivers
Wiring:
Spi Screen
Display--------Raspberry Pi
BL--------------pin 12 (GPIO 18)
SCK------------pin 23 (GPIO 11)
MISO----------pin 21 (GPIO 9)
MOSI----------pin 19 (GPIO 10)
CS--------------pin 24 (GPIO 8)
RST------------pin 22 (GPIO 25)
D/C-------------pin 18 (GPIO 24)
VIN-------------pin 17 (3.3v)
GND-----------pin 20 (GND)
Buttons
Shared ground across all buttons and joystick. Use extra protoboard pins to make all of the grounds common.
Buttons are wired to pins 0-13 and A2. Joystick axies are wired to A0 and A1.
Tricks:
I used electrical tape to hold the battery leads in place during assembly. The risers in the prints will apply the pressure needed to make contact.
Similar models
thingiverse
free
![GPIO & Camera Hole Cover for Raspberry Pi 3 Ender 3 Case by MrNellow](/t/8173766.jpg)
GPIO & Camera Hole Cover for Raspberry Pi 3 Ender 3 Case by MrNellow
...useful if you don't need any gpio pins or raspberry pi camera. if you need any gpio pin, you can shrink gpio cover by x axis.
grabcad
free
![Arcade Cabinet v.0.1](/t/1622454.jpg)
Arcade Cabinet v.0.1
...arcade cabinet v.0.1
grabcad
my first arcade cabinet based on raspberry pi 3. buttons and joystick connected directly to gpio.
thingiverse
free
![Official 7" Raspberry Pi Screen Case by Jap_MK2](/t/8565632.jpg)
Official 7" Raspberry Pi Screen Case by Jap_MK2
...o still be able to attach the ribbon/extension cable for gpios. but this should not be an issue, it still worked out pretty well.
thingiverse
free
![Raspberry Pi GPIO Connector by vexaae](/t/820036.jpg)
Raspberry Pi GPIO Connector by vexaae
...y) or get a gpio ribbon cable from ebay (expensive but nice).
d) print your own female-to-female gpio connector (cheap and nice).
thingiverse
free
![9 pin ( Atari, Amiga C64 and others) Joystick tester by mrholub](/t/8068002.jpg)
9 pin ( Atari, Amiga C64 and others) Joystick tester by mrholub
...an universal pcb 2x8 cm and put it in 3d printed enclosure of my own design.
i've used an usb connector for powering circuit.
thingiverse
free
![IDE jumper cable clip by averypierce](/t/8784160.jpg)
IDE jumper cable clip by averypierce
...hold breadboard jumper cables to ide cable. useful if you're using old 40 pin ide cable to connect to raspberry pi gpio pins.
thingiverse
free
![Raspberry Pi Zero WiFi Camera Case for use with GPIO by Timo94](/t/8287215.jpg)
Raspberry Pi Zero WiFi Camera Case for use with GPIO by Timo94
...4
thingiverse
quick remix so you can use the gpio pins while your raspberry pi zero is in the case.
please download on youmagine
thingiverse
free
![Button and led holder for Mini NES Pi 3 Case by ElTacoLoco](/t/8767042.jpg)
Button and led holder for Mini NES Pi 3 Case by ElTacoLoco
...e or if you hurt yourself or others.
if you are unfamiliar with gpio/electronics/raspberry pi be careful and read up on it first.
thingiverse
free
![40 Pin Raspberry Pi A+, B+, 2, 3 GPIO Connector by billioncash](/t/8944693.jpg)
40 Pin Raspberry Pi A+, B+, 2, 3 GPIO Connector by billioncash
...thingiverse
modified blandman's gpio connector file to support the 40 pin connector found on the raspberry pi a+, b+, and 2.
grabcad
free
![Raspberry Pi GPIO Breakout board](/t/5171932.jpg)
Raspberry Pi GPIO Breakout board
...raspberry pi gpio breakout board
grabcad
raspberry pi gpio breakout board with pin header 2x20 pin male, 8.4 mm high
Dmradford
thingiverse
free
![Snowboard Rack by DMRadford](/t/8266793.jpg)
Snowboard Rack by DMRadford
...snowboard rack by dmradford
thingiverse
just a thinner version of rjeanbrice's hook.
thingiverse
free
![Bicycle pump nozzle adapter by DMRadford](/t/9222497.jpg)
Bicycle pump nozzle adapter by DMRadford
...e pump nozzle adapter by dmradford
thingiverse
simple pump adapter for using a bicycle pump to inflate beach balls or pool toys.
thingiverse
free
![Screw assembly for thing:21357 by DMRadford](/t/8206209.jpg)
Screw assembly for thing:21357 by DMRadford
...(up to 12mm to hold the base to the swivel. this removes the need for glue and gives a more robust attachment between the pieces.
thingiverse
free
![GFI / GFCI faceplate with Extra Cable holders by DMRadford](/t/8202224.jpg)
GFI / GFCI faceplate with Extra Cable holders by DMRadford
...cement faceplate for standard us gfi / gfci outlet with built-in hooks to hold additional cables that get swapped out frequently.
thingiverse
free
![Clip on Headphone hook for desks by DMRadford](/t/8200727.jpg)
Clip on Headphone hook for desks by DMRadford
...s (glass), and one for 3/4" thick desks. designed where the thicker end of the clip is 2mm wider than the desk it's for.
thingiverse
free
![Maytag dishwasher handle by DMRadford](/t/8138842.jpg)
Maytag dishwasher handle by DMRadford
...ever if your dishwasher is not in that list, but still uses handle / latch part number wpw10130695, this handle should still fit.
thingiverse
free
![E3Dv6 X-Carriage for Anet A2 / Tevo / Creality by DMRadford](/t/8537165.jpg)
E3Dv6 X-Carriage for Anet A2 / Tevo / Creality by DMRadford
... for use with a stock anet a2, however this should also work for tevo terantula and creality cr10 with minor if any adjustments.
thingiverse
free
![Black and Decker 20v battery wall mount 4x by DMRadford](/t/8194156.jpg)
Black and Decker 20v battery wall mount 4x by DMRadford
... or ceiling mounted (inside a cabinet). it's 294mm long so you'll need either a large printer or to print it at an angle.
thingiverse
free
![DC Converter electrical box by DMRadford](/t/8241338.jpg)
DC Converter electrical box by DMRadford
..._title_o02_s00?ie=utf8&psc=1
https://www.amazon.com/gp/product/b077tfhlws/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=utf8&th=1
thingiverse
free
![Anet Filament Spool Rack Top Mount Bracket A8 / A2 by DMRadford](/t/8591830.jpg)
Anet Filament Spool Rack Top Mount Bracket A8 / A2 by DMRadford
...anet filament rack. this was designed to mount on top of the anet a2, however could be used for a wall or other type of mounting.
Mini
turbosquid
$10
![Mini Mini Luceplan](/t/13457783.jpg)
Mini Mini Luceplan
...
royalty free 3d model mini mini luceplan for download as max on turbosquid: 3d models for games, architecture, videos. (1227359)
3d_ocean
$39
![Mini Cooper](/t/567543.jpg)
Mini Cooper
...mini cooper
3docean
cabrioler cooper mini
mini cooper cabrioler
3d_export
$30
![Mini lathe](/t/12401292.jpg)
Mini lathe
...mini lathe
3dexport
mini lathe
3d_export
$5
![mini mouse](/t/11460646.jpg)
mini mouse
...mini mouse
3dexport
mini mouse
3d_export
$5
![mini house](/t/11460303.jpg)
mini house
...mini house
3dexport
mini house
3d_export
free
![Mini Mecha](/t/11928245.jpg)
Mini Mecha
...mini mecha
3dexport
concept of mini mecha
3d_ocean
$20
![Mini Gun](/t/369001.jpg)
Mini Gun
...mini gun
3docean
gatling gun gun machine gun mini gun weapon
model of a mini gatling gun.
3ddd
free
![Herve mini](/t/628699.jpg)
Herve mini
... кофейный , herve
http://www.mobiliavenanti.it/ru/products/hervè-mini
3d_export
$5
![mini wall](/t/11419293.jpg)
mini wall
...mini wall
3dexport
mini wall for living room
3d_export
$5
![mini bank](/t/11716530.jpg)
mini bank
...mini bank
3dexport
mini bank 3d model