Thingiverse
Ring Lamp (Customizable) by geit_de
by Thingiverse
Last crawled date: 3 years, 1 month ago
Ok, this is the result of a small FreeCAD session: A little ring lamp with 325mm diameter. You need a printer with around 200x200mm build plate to be able to print a quarter ring.
Key Features:
When designing this I had some key features in mind:
° simple and clean print
° avoid the led strips glue tape on the back at all cost.
° add a simple compartment for the electronics.
° wire management
° easy to print.
Requirements:
1x 5V power supply
1x Switch
1x LED strip. (60 pixel/m or more)
WARNING! You need a LED strip without a rubber dome. Just the plain PCB with the LEDs and resistors soldered on.
Printing:
You need to print a the socket, the lid and four ring pieces. One of the ring segments has an opening for the wiring. The other file marked with 3x need to be printed three times.
The ring segment files have build in support. They need to be printed flat on the bed and without any support.
There will be a small wall of support in front of the LED slot. Just push along it and it will release very easy. The included images show the support removal and how to insert the LED strip.
Once done you can use small filament pieces and stuff them into the three holes. Along with a little glue you can glue the segments together.
Before gluing the bottom ring openings together, slide in the LED strip into the ring section. It must be a PCB only LED strip. Strips with a defusing rubber dome cover, will not work. There is a similar opening in the ring socket. Just add a little glue and align the wire guide opening before placing the ring into the slot of the base.
Slide in the switch and the power wire, connect the ESP32 and done. This is basic stuff. 5V to 5V, GND to GND and the ring light data line to pin G23.
You can use any kind of software to drive the ring lamps LED strip. Even use an Arduino and some example code. I will release the source of my solution once I have finished it.
Current Features:
° web interface
° OTA update support
° flash settings support
° 12 effects (static, rainbow, fire place, RGB fader, ...)
° sound support (hour/30 min gong) (requires DFPlayer sound module)
° timed power mode: The ring lamp turns on and off at a specific hours.
° timed dimming mode: The ring lamp changes brightness at specific hours.
° timed sound mode: The ring lamp changes volume at specific times.
Planned Features:
° clock face effect
° effect randomizer
Customize:
To customize the ring you need FreeCAD 0.19.1 or up. The model is fully parametric and you should be able to modify stuff like the size of the opening for the switch by just tweaking the spreadsheet. Of course this also works for all other dimensions.
If there are any questions feel free to write a comment.
Key Features:
When designing this I had some key features in mind:
° simple and clean print
° avoid the led strips glue tape on the back at all cost.
° add a simple compartment for the electronics.
° wire management
° easy to print.
Requirements:
1x 5V power supply
1x Switch
1x LED strip. (60 pixel/m or more)
WARNING! You need a LED strip without a rubber dome. Just the plain PCB with the LEDs and resistors soldered on.
Printing:
You need to print a the socket, the lid and four ring pieces. One of the ring segments has an opening for the wiring. The other file marked with 3x need to be printed three times.
The ring segment files have build in support. They need to be printed flat on the bed and without any support.
There will be a small wall of support in front of the LED slot. Just push along it and it will release very easy. The included images show the support removal and how to insert the LED strip.
Once done you can use small filament pieces and stuff them into the three holes. Along with a little glue you can glue the segments together.
Before gluing the bottom ring openings together, slide in the LED strip into the ring section. It must be a PCB only LED strip. Strips with a defusing rubber dome cover, will not work. There is a similar opening in the ring socket. Just add a little glue and align the wire guide opening before placing the ring into the slot of the base.
Slide in the switch and the power wire, connect the ESP32 and done. This is basic stuff. 5V to 5V, GND to GND and the ring light data line to pin G23.
You can use any kind of software to drive the ring lamps LED strip. Even use an Arduino and some example code. I will release the source of my solution once I have finished it.
Current Features:
° web interface
° OTA update support
° flash settings support
° 12 effects (static, rainbow, fire place, RGB fader, ...)
° sound support (hour/30 min gong) (requires DFPlayer sound module)
° timed power mode: The ring lamp turns on and off at a specific hours.
° timed dimming mode: The ring lamp changes brightness at specific hours.
° timed sound mode: The ring lamp changes volume at specific times.
Planned Features:
° clock face effect
° effect randomizer
Customize:
To customize the ring you need FreeCAD 0.19.1 or up. The model is fully parametric and you should be able to modify stuff like the size of the opening for the switch by just tweaking the spreadsheet. Of course this also works for all other dimensions.
If there are any questions feel free to write a comment.
Similar models
thingiverse
free
Ring Lamp Dual V2 (Customizable) by geit_de
...from v1, but it of course will only drive the inner led strip. in the future the same firmware will be suitable for both version.
thingiverse
free
Printed LED Desk lamp by Promocable
...he wires from the led strips
final assemble screwing the printed parts together
done -> profit
i apologize for my englisch. :/
thingiverse
free
Another Circular Lamp by mistic100
...wice.
mode 0 : not configurable
mode 1 : long touch to change the temperature
mode 2 : not configurable
mode 3 : not configurable
thingiverse
free
Lithophane Frame
... wire in the switch and finally connect wires 1 and 4 (+5v and ground) of a usb plug to the appropriate wires for the led strips.
thingiverse
free
Articulating LED Strip Lamp by Mossball765
...g around. regular single colour led strips can be used as well.
1x 12v 5a power supply
edit 2020-11-03
added the missing knob stl
thingiverse
free
Amoeba LED Lamp-V1 by ChrisTheViolaNerd
...ints, and negative battery terminal will be wired to the (com) switch point. no wires will be connected to the (nc) switch point.
thingiverse
free
Hand-held LED Light / LED stick for photography or video recording
...ip
1x warm white led strip
2x 14mm round on/off switch
4x m3x5mm bolts
1x 9v battery
5min epoxy glue
red and black wires
enjoy :)
grabcad
free
LED strip segment 5V white
...led strip segment 5v white
grabcad
https://nerd-corner.com/glare-free-lamp-and-powerbank/
cults
free
SQUARE LED LAMP
...ff switch mount. optimised for the best printing quality on fdm printers, support free and doesn't need glue to be assembled.
thingiverse
free
Tower Lamp by vortex_pr
...ire
led strip
some wires
power supply (to the led strip)
update:
added optional circular led support, instead of rectangular one.
Geit
thingiverse
free
GeitPrinter by geit_de
...(magnetic parking)
2x m3 15mm counter sunk enclosure screws (e3dv6 fan)
8x 4mm cubic neodymium magnets (magnetic parking)
3dwarehouse
free
model houdertje voor in geit
...model houdertje voor in geit
3dwarehouse
model houdertje voor in geit
3dwarehouse
free
Playground skip goat _Wip geit toestel
...playground skip goat _wip geit toestel
3dwarehouse
3dwarehouse
free
Geit Kip en Konijnenhok voor open verblijf
...geit kip en konijnenhok voor open verblijf
3dwarehouse
hok geschikt voor 2-3 dwergeitjes tot 50-60 cm 3-4 konijnen 3-5 kippen
3dwarehouse
free
Goat
...goat 3dwarehouse goat geit 3d geit 3d goat...
3dwarehouse
free
estonian 'my home'
...'my home' 3dwarehouse its my home in estonia autor geit griin #estonia #gonsiori...
3dwarehouse
free
Stal / Barn
...invented it myself. #barn #boerderij #cow #cows #farm #geit #geitn #hok #koe #koeien #schaap #schapen #sheep...
3dwarehouse
free
Ibex (adult male)
...steep regions to avoid predators. #animal #beast #beest #dier #geit #goat #ibex #mammal #mountain...
3dwarehouse
free
schaap
...leveren. het is een herkauwer, nauw verwant met de geit de soort behoort tot het geslacht ovis, waar ook...
Customizable
3d_export
$10
customizable sd port
...customizable sd port
3dexport
customizable sd port
turbosquid
$99
Customizable character
...alty free 3d model customizable character for download as max on turbosquid: 3d models for games, architecture, videos. (1152525)
turbosquid
$1
Customizable Mug
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Customizable Spider Mech
... free 3d model customizable spider mech for download as blend on turbosquid: 3d models for games, architecture, videos. (1462055)
turbosquid
$20
Customizable Egyptian Pillar
...zable egyptian pillar for download as ma, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1307376)
turbosquid
$75
Fully Customizable Hospital
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Customizable Caste Pieces
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
Customizable Tea Cup
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Water Bottle(Customizeable)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$49
Book customizable 3D Model
...3dexport
book booshelf novel teach library learn read pages cover fairy tales
book customizable 3d model guitargoa 74240 3dexport
Lamp
archibase_planet
free
Lamp
...lamp
archibase planet
lamp reading lamp table lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp reading lamp table lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp table lamp reading lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp table lamp reading lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp reading lamp table lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp reading lamp table lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp table lamp reading lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp table lamp reading lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp reading lamp table lamp lantern
lamp - 3d model (*.3ds) for interior 3d visualization.
3d_ocean
$6
Lamp
...lamp
3docean
lamp
a high quality lamp.
Ring
3d_export
$5
ring
...ring
3dexport
ring
3d_export
free
ring
...ring
3dexport
ring
3d_export
free
ring
...ring
3dexport
ring
3d_export
free
ring
...ring
3dexport
ring
3d_export
$10
ring
...ring
3dexport
lord of the rings
3d_export
$5
ring
...ring
3dexport
golden ring
3d_export
free
ring
...ring
3dexport
cherub ring
3d_export
$10
ring
...ring
3dexport
3d ring model
3d_export
$5
ring
...ring
3dexport
ring 3d model
3d_export
$5
ring
...ring
3dexport
ring top black...