Similar models
thingiverse
free
RigidBot Bar End Cap by tchotchke
...rigidbot bar end cap by tchotchke
thingiverse
push in end cap for covering the ends of the rigidbot bars.
thingiverse
free
RigidBot Dioder Clip by tchotchke
...p for rigidbot clip from jwolee.
there are different versions, designed to work with the cabled end, capped end, or the middle.
thingiverse
free
XT60 / XT-60 UNBALANCED AND STORAGE CAPS by sultan
...nifold errors, but prints fine in repetier with cura.
(rotate -90 to print on end)
printed on rigidbot with rumba electronics
thingiverse
free
Rigidbot spool rod quick change caps by JP1
...t to allow the cap to tighten as you press it down over the tubing. use calibrated filament to make sure they print as designed.
thingiverse
free
RigidBot Heater LED Light Pipe by tchotchke
...hotchke
thingiverse
small caps for putting the the circular pot adjustment openings near the extruders. print in clear plastic.
thingiverse
free
knex end cap
...knex end cap
thingiverse
knex end-cap
thingiverse
free
Cap End by duarteg
...cap end by duarteg
thingiverse
cap end for a toy
thingiverse
free
MTB Handelbar end cap by cb85de
...mtb handelbar end cap by cb85de
thingiverse
just a slim end cap for a mtb handelbar end cap. 20mm / 22mm
thingiverse
free
XRT End Cap by StuckAtWork
...by stuckatwork
thingiverse
the vs, which this is a remix of, fit the thread adapter, but not the end cap. this fits the end cap.
thingiverse
free
Cord cap / rope end cap by i6o6
...cord cap / rope end cap by i6o6
thingiverse
simple cap for the end of a rope. the knot in the rope will hide in the cap.
Pdidonna
thingiverse
free
9V Battery Dispenser by pdidonna
...9v battery dispenser by pdidonna
thingiverse
9v battery dispenser.
thingiverse
free
Rigidbot Flat Cable Clamp by pdidonna
...le clamp by pdidonna
thingiverse
flat ribbon cable clamp for rigidbot extruder. use with 25mm flat braided expandable sleaving.
thingiverse
free
Rigidbot Smart LCD Bracket by pdidonna
...d controller case to the rigidbot. i used this case http://www.thingiverse.com/thing:87250 with the pockets on the bottom cover.
thingiverse
free
Rigidbot LED Mount and Rail by pdidonna
...72w ip65 glue waterproof rgbw leds to mount on the rails and a bunch up clips to prevent the led strip from lifting off the rail.
Rigidbot
thingiverse
free
z_bracket rigidbot
...z_bracket rigidbot
thingiverse
z_bracket for 4 screws
thingiverse
free
Rigidbot Side Brackets by MKAY666
...rigidbot side brackets by mkay666
thingiverse
rigidbot side and z brackets
thingiverse
free
RigidBot Caliber Holder by dafes
...rigidbot caliber holder by dafes
thingiverse
caliber holder for the rigidbot frame
thingiverse
free
Rigidbot printerbed by nickbernstein
... printerbed by nickbernstein
thingiverse
build plate for rigidbot 3d printer. intended to be be c&c fabricated from aluminum
thingiverse
free
Filament Guide for Rigidbot by omegdadi
...filament guide that clips onto the frame of a rigidbot 3d printer. inspired by the rigidbot side cutter tool holder by steve0605.
thingiverse
free
RigidBot monitor by EremaStar
...rigidbot monitor by eremastar
thingiverse
lcd
thingiverse
free
RigidBot Z-Axis Support by dafes
...rigidbot z-axis support by dafes
thingiverse
support structure for the z-axis upgraded rigidbot.
thingiverse
free
RigidBot Bar End Cap by tchotchke
...rigidbot bar end cap by tchotchke
thingiverse
push in end cap for covering the ends of the rigidbot bars.
thingiverse
free
Rigidbot Hex Key Holder by Steve0605
...rigidbot hex key holder by steve0605
thingiverse
a place to keep your hex keys handy for the rigidbot printer.
Cap
thingiverse
free
CAP
...cap
thingiverse
cap antenna base
thingiverse
free
1" Cap cap by Doz1971
...1" cap cap by doz1971
thingiverse
a cap to assist in re-stuffing electrolytic capacitor cans in vintage electronics.
thingiverse
free
TINKER CAP
...tinker cap
thingiverse
cap
thingiverse
free
caps by mjk2203
...caps by mjk2203
thingiverse
caps
thingiverse
free
cap by Artformer
...cap by artformer
thingiverse
cap
thingiverse
free
cap
...cap
thingiverse
9
thingiverse
free
Snapback Cap
...snapback cap
thingiverse
snapback cap, for different headsizes just scale the cap up or down.
thingiverse
free
capped by cheeba
...capped by cheeba
thingiverse
just a cap
thingiverse
free
RJ45 Cap
...rj45 cap
thingiverse
this is a rj45 cap
thingiverse
free
oil cap
...oil cap
thingiverse
oil cap
End
thingiverse
free
32mm end cap ball end
...32mm end cap ball end
thingiverse
modified my previous design to have rounded cap ending.
thingiverse
free
Preonic End
...preonic end
thingiverse
end piece for the rev 2 preonic
thingiverse
free
vacuum end shop vac end by luiscollie
...verse
shop vac end with tight end for more suction....this fits standard shop vac end about 58 mm id.. easy to print standing up
thingiverse
free
end mill tray for 6 end mills by jeffcarlsbad
...end mill tray for 6 end mills by jeffcarlsbad
thingiverse
end mill tray for 6 end mills
thingiverse
free
end mill tray for 4 end mills by jeffcarlsbad
...end mill tray for 4 end mills by jeffcarlsbad
thingiverse
end mill tray for 4 end mills
thingiverse
free
Maze's End
...maze's end
thingiverse
this a fan work of the maze's end from magic: the gathering
thingiverse
free
Heim Rod End / End Stangen Gelenk by MBWolf
...heim rod end / end stangen gelenk by mbwolf
thingiverse
standard heim rod end / einfaches endstangengelenk
thingiverse
free
THE END IS NEAR Stencil
...the end is near stencil
thingiverse
the end is near
thingiverse
free
End stop by Ha3d
...end stop by ha3d
thingiverse
end stop
thingiverse
free
Book end by henrykaplan
...book end by henrykaplan
thingiverse
this is a book end.