Similar models
thingiverse
free
Tensile Tetras by Fredbartels
...bstantially smaller than the faces of the tetrahedron. roughly 3/4 the size.
the tetras are lovely slowly spinning in the wind!
thingiverse
free
Conduit Hook by eussrh
... the conduit. there is also a slot allowing you to secure it with a zip tie if you want, but i haven't found that necessary.
thingiverse
free
twine holder by discsaar
...twine holder by discsaar
thingiverse
twine holder
thingiverse
free
Twine Cutter
...twine cutter
thingiverse
needed a twine cutter for square hay bails
thingiverse
free
Twinings stackable tea caddy
...a caddy that is (imho) more attractive and space efficient.
the dimensions of the caddy are taken from the twinings tea bag size.
thingiverse
free
Twine holder for mower by Yari27
...twine holder for mower by yari27
thingiverse
twine holder for viking mower to ignite.
thingiverse
free
fujifilm xt1 vertical grip cover by swennert
...ical grip. the previous owner lost the cover (to protect the pins while you are not using the grip), so i decided to make my own.
thingiverse
free
Gradening Hook by Joseph_Antony
... thinking of a easier reusable solution and hence the hook.
attach a hook to either end of a strong twine and you are good to go.
thingiverse
free
AR-15 pistol grip v.2 by henkel111
...l grip.
thanx to lookoutforchris (https://grabcad.com/lookoutforchris-1) for model of a lower i used for grip exact measurements.
thingiverse
free
Sony RX100 Mark 1 Hasselblad Stellar Grip by Jtm
... rx100 and when i saw the stellar's grip i just knew i had to make it. may make a more pronounced version in the near future.
Bajnopi
thingiverse
free
Knuckles/Boxer by Bajnopi
...knuckles/boxer by bajnopi
thingiverse
it is necessary to change the size for hand size.
thingiverse
free
Poly skull pen holder by Bajnopi
... pen holder by bajnopi
thingiverse
print settings:
layer height: 0.2
walls: 1
infill: 5/10%
speed: 50
(took me 20 hour to print)
Rambo
thingiverse
free
Vertical Rambo Mount
...vertical rambo mount
thingiverse
vertical mount for full rambo board. lid snaps on.
thingiverse
free
rambo by happydead
...rambo by happydead
thingiverse
broad head case
thingiverse
free
Couteau Rambo by Tsarmanil
...couteau rambo by tsarmanil
thingiverse
un couteau issu de rambo 3 le film taille réelle.
thingiverse
free
Rambo Figure Stand by trpeder
...rambo figure stand by trpeder
thingiverse
rambo figure stand
thingiverse
free
RAMBo MendelMax Mount by dstonef
...rambo mendelmax mount by dstonef
thingiverse
combined ramps->rambo adapter with ramps mount.
thingiverse
free
Rambo Board Holder v1.4
...rambo board holder v1.4
thingiverse
quick rambo v1.4 holder for my mpcnc build. just the basics.
thingiverse
free
RAMBO enclosure by eburt
...rambo enclosure by eburt
thingiverse
streamline this enclosure.
thingiverse
free
Rambo knife stand by Remcovandijk
...nd by remcovandijk
thingiverse
rambo 2 knife stand.
printed on a anycube i3 mega
you can print the standers by multiply the one.
thingiverse
free
RAMBO-minus-PI
...for the top
4 - m3 x 6 for the rambo
4 - screws of your choice for mounting the enclosure.
the enclosure also holds 2 40mm fans.
thingiverse
free
RAMBo Control Board Housing by shingabiss
...ing by shingabiss
thingiverse
this is a cover for the rambo board that is deep enough to house all cables attached to the board.
Knife
thingiverse
free
Knife
...knife
thingiverse
knife
thingiverse
free
Knife
...knife
thingiverse
knife
thingiverse
free
Knife
...knife
thingiverse
just a knife made with love
thingiverse
free
Knife by gnamp
...knife by gnamp
thingiverse
knife
thingiverse
free
Knife by Mari5Gt
...knife by mari5gt
thingiverse
knife
thingiverse
free
knife by yjh777
...knife by yjh777
thingiverse
knife
thingiverse
free
knife by nagato
...knife by nagato
thingiverse
knife
thingiverse
free
knife by stevehaines
...knife by stevehaines
thingiverse
knife
thingiverse
free
Knife by fonex
...knife by fonex
thingiverse
knife
thingiverse
free
KNIFE by leonk
...knife by leonk
thingiverse
knife