Rail 1:25

...steeldeck safety rail 8' by rory1 thingiverse at a scale of 1:25

...railing 1 by nyc3d thingiverse upper railing 1

...igolf thingiverse this is just the xzf11 frame modified to have rail holes every 25 mm to make mounting of mgn12 rails possible.

...railing 1 low by nyc3d thingiverse lower railing section 1

...sing a 25 mm wardrobe rail. includes caps to terminate the rail. rail used:https://www.clasohlson.com/no/garderobestang/p/40-8208

...3 to 1 flex rail fischertechnik thingiverse 3 to 1 flex rail block.

... 40mm can be mounted with these holders. the zoom feature of your slicer should allow different diameters for your clothes rails.

...shelly 1 din rail mount by dany_donze thingiverse a din rail mount for shelly 1

... left-right with a slight lift of the mount. 3 holes for 1/4-20 bolt (included) so you can position for best distance from rail.

... flashlight holder to mount in rail. it has been designed to mount 25 mm diameter flashlight. only for airsoft guns... of course.

...-----------------------------------------------------------------------табличка 25, не знаю зачем она вам, но вот вам табличка 25

...rofile. it gives you a better finish at the end of exposed cut ends. it also prevents you from cutting yourself with sharp edges.

...25/17 by andr56338 thingiverse 25/17

...potez 25 by cparini thingiverse potez 25

...b-25 by 0kami_sweetfang thingiverse simple b-25

...25 stones by hdc thingiverse a ring with 25 holes for stones.

...hinge 25 x 25 x 2.5 by cappy0815 thingiverse hinge for light applications. dimensions width: 25 mm length: 51 mm (2 x 25,5)

...butterfly 25 by wslab thingiverse butterfly design 25 search "wslab" for more designs.

...rek1977 thingiverse these blowouts used with 25 mm fans, connected with 2 screws 3 mm l ~ 15-25 mm, between the parts - springs.

...vector rail thingiverse vector rail

...railing thingiverse for gaming and modeling

...fingerboard rail thingiverse cool rail for fingerboarding!!!!

...guide rail thingiverse different guide rail options. i found the long rail provide to most stability.

...rail for tramways thingiverse it is just a replacement for the rails of tramways.

...scope rail by rundown thingiverse scope rail for a lower rail.

...u need. this rail segment has a 1 inch wide baseplate. this surface is what i used to glue the rail into the target application.

... and realized it used a dovetail rail contrary to a picatinny rail, made this and super glued it on my rifle, no problems so far.

...ak side rail mount with extra rail by homiestarks thingiverse just added another rail on it.

...y rail adapter. you can either print a long 'combined' rail, or separate parts, and glued them together (easier to print)

...magic token +1/+1 & -1/-1 by kilgara2b thingiverse a magic the gathering token +1/+1 and -1/-1

...tudiosgaming thingiverse if you are in need of the 4pstudiosgaming +1/+1 and -1/-1 counters, then you came to the right page :-p

... 1/6, 1/8, 1/10, and 1/12 sized wedges as well as a circular base for them to fit onto. there are no labels on any of the pieces.

...dapter for syphon - 1 1/4" to 1 1/2" h10,5mm the project was realized with tolerances for printing with abs + tape ptf.

...l fit both 1 1/8" and 1 1/5" bearing cups. i used a 3/8ths" threaded rod with nuts and thick washers on each end.

...design cheeseborough clamp for hanging lightfixtures and other items onto 1-1/4"-1-1/2" npt pipe. use at your own risk.

...them instead of money coin in your supermarket cart or in your swimming pool locker. edit : updated 1£ coin with new dimensions

...d adapter 1" to 1" 1/4 by printerforever thingiverse this is an adapter 1" to 1" 1/4 (male to male) enjoy !

...playstation 2, 1:1 by vitting thingiverse made a 1:1 playstation 2.

...re thinner and actually fit within each other to show equivalent fractions. also, check out the same version with braille (here).