Similar models
grabcad
free
![Wall Power Adapter](/t/5327926.jpg)
Wall Power Adapter
...wall power adapter
grabcad
rough model of a wall power adapter. australian plug can be removed and remodelled.
3dwarehouse
free
![removable wall](/t/6775264.jpg)
removable wall
...emovable wall
3dwarehouse
simple and sizeable wall to partition areas where you don't, or can't build, a permanent wall.
thingiverse
free
![Cover by Egholm](/t/5080142.jpg)
Cover by Egholm
...cover by egholm
thingiverse
chimney was removed and laft a hole in the wall. the hole can be blocked with this cover
thingiverse
free
![retaining nob by UWM_DCRL](/t/8953073.jpg)
retaining nob by UWM_DCRL
...verse
general knob for holding relatively flat pieces against the wall. can be tacked to the wall and pivoted for easy removal.
thingiverse
free
![Toilet paper holder which can stick on the wall by 3M wall sticker. by j112358](/t/9036051.jpg)
Toilet paper holder which can stick on the wall by 3M wall sticker. by j112358
...se
toilet paper holder with two poles. it can support two rolls of toilet paper and stick on the wall with 3m removable sticker.
3dwarehouse
free
![Kitchen Project 2013- Walls Removed](/t/9325373.jpg)
Kitchen Project 2013- Walls Removed
...kitchen project 2013- walls removed
3dwarehouse
dining room walls removed. den wall halved.
thingiverse
free
![mul-t-lock Entr remote wall mount by Hauzer](/t/8139837.jpg)
mul-t-lock Entr remote wall mount by Hauzer
...r smart lock remote
you can use 2 screws or just glue it to the wall so you can replace batteries without removing the wall unit.
thingiverse
free
![Wall Mounted Holder for HICTOP 3D Print Removal Tool by danielwdunn](/t/8605939.jpg)
Wall Mounted Holder for HICTOP 3D Print Removal Tool by danielwdunn
...it using common wood screws. this was designed with tinkercad and a caliper by measuring the hictop 3d print removal tool handle.
3dwarehouse
free
![Sonance Invisible IS8 / IS10W](/t/9496089.jpg)
Sonance Invisible IS8 / IS10W
...10w
3dwarehouse
plaster over in wall full range speaker or in wall subwoofer with removable back box (can be deleted from model)
thingiverse
free
![Nose](/t/4768458.jpg)
Nose
...nose
thingiverse
i have removed the stand and added a slot for a screw head so that it can be fixed to the wall.
Portabledesk
grabcad
free
![portabledesk](/t/2038903.jpg)
portabledesk
...125mm, dust and waterproof when folded because of the rubber band between lids!
the drawers can be modified if needed more space!
grabcad
free
![Rabaconda portabledesk toolbox](/t/1843743.jpg)
Rabaconda portabledesk toolbox
...rabaconda portabledesk toolbox
grabcad
busy rabaconda toolbox, have a few days to go to work. my first pictures
grabcad
free
![trolley portabledesk](/t/1712380.jpg)
trolley portabledesk
... the aesthetics, giving the image a trolley with rounded edges can be personalized with your own flag or the name of the company.
grabcad
free
![Portabledesk](/t/1748891.jpg)
Portabledesk
...nion) a straight leg design may be easier to assemble and store but the chances of the legs sinking in wet conditions are higher.
grabcad
free
![Portabledesk for Rabaconda](/t/1855566.jpg)
Portabledesk for Rabaconda
... fully closed.
<br />800mm x 400 mm without the optional rubberized shell.
<br />total weight of 28ibs
<br />
grabcad
free
![Rabaconda Portabledesk Challenge](/t/1632547.jpg)
Rabaconda Portabledesk Challenge
...think that plastic box offered the best possibilities for the design requirements, light, slim and low cost in serial production.
grabcad
free
![Portabledesk - 10 seconds](/t/1777096.jpg)
Portabledesk - 10 seconds
...it is possible to add a lock with a key.
for more information about the installation cinématic, see the movie, and or contact me.
grabcad
free
![Portable Bike Racer Tool Desk Challenge](/t/1644331.jpg)
Portable Bike Racer Tool Desk Challenge
...portable bike racer tool desk challenge grabcad this is portabledesk design by myself. it is compact in size and...
grabcad
free
![Rabaconda Protable Tool Desk - Joshua Chung](/t/1632249.jpg)
Rabaconda Protable Tool Desk - Joshua Chung
...rabaconda protable tool desk - joshua chung grabcad portabledesk this design was modified from my instrument storage case...
Rabaconda
grabcad
free
![Rabaconda portabledesk toolbox](/t/1843743.jpg)
Rabaconda portabledesk toolbox
...rabaconda portabledesk toolbox
grabcad
busy rabaconda toolbox, have a few days to go to work. my first pictures
grabcad
free
![Rabaconda case for work](/t/1870267.jpg)
Rabaconda case for work
...rabaconda case for work
grabcad
a workcase for bikers.
grabcad
free
![TOOL BAG RABACONDA](/t/1868069.jpg)
TOOL BAG RABACONDA
...tool bag rabaconda
grabcad
modular fully prepared in print and flare
cg_trader
free
![Rabaconda PC2 Bike Racer Tool Desk](/t/2883128.jpg)
Rabaconda PC2 Bike Racer Tool Desk
...rabaconda pc2 bike racer tool desk
cg trader
rabaconda pc2 bike racer tool desk
grabcad
free
![TOOL BAG RABACONDA](/t/1680001.jpg)
TOOL BAG RABACONDA
...tool bag rabaconda
grabcad
prepared in print 18 gauge cold, material galvanized aluminium alfajor
grabcad
free
![Rabaconda portable desk](/t/1861392.jpg)
Rabaconda portable desk
...rabaconda portable desk
grabcad
i decided to use aluminium to make it robust. it weighs around 14 kg.
grabcad
free
![TOOL BOX RABACONDA](/t/1764567.jpg)
TOOL BOX RABACONDA
...tool box rabaconda
grabcad
tool bag
cold sheet prepared in 18 gauge, stainless steel sheets, alfajor
grabcad
free
![Rabaconda workcase](/t/1686403.jpg)
Rabaconda workcase
...er
latch - steel
wall holder - steel
hinge - steel
elements are connected by rivets. magnetic strips is possible add to drawers.
grabcad
free
![Rabaconda portable table box](/t/1656263.jpg)
Rabaconda portable table box
...ickness but some modification of the biddings and adding sttifiners.
i used circlip for the hinges on the footings and the brace.