Thingiverse
pylon racer by Sulhan
by Thingiverse
Last crawled date: 3 years, 1 month ago
Sorry for my english, trust me im trying to describe as good as i can :)
After trying some model, i decide to draw my own model using fusion 360.
Wing span 80cm, weight without electronic is about 149gram.
this plane is not for newbi on rc plane, speed is medium to fast. wing profile using semi simetris mh30.
to print fuselage is not any special, except front part you need some thickness for motor mount. all fuse part is 1 perimeter (0.4mm) and no infill, some with top/ bottom layer to ease of gluing and add some rigidity.
to print wing you need some attention. 1 perimeter and infil 1.5%. this infill just for manage airfoil curvature. add top and bottom layer to ease gluing and make solid join.
wing part just one side, so you need to copy and mirroring to make other side
CG locate at front wall of spar canal. wing mount to fuselage by 4mm screw.
for glueing, im using uhu all plastics, this glue work very well for thin 3d print part.
i make 2 front (nose) model, shot nose and long nose. long nose will make benefit to manage center of grafity.
setting for plane:
aileron up +- 5mm, and +-5mm down
elevator +- 3mm up, 2mm down
you need set end point to do this.
add exponent 30% or more
my electronic setup:
brushless 2204 ccw 2300kv
tgs propeller 4.75 x 4.75
esc 20A
lipo 850mah 3s
servo 9gr
offcourse you can use your own setup
After trying some model, i decide to draw my own model using fusion 360.
Wing span 80cm, weight without electronic is about 149gram.
this plane is not for newbi on rc plane, speed is medium to fast. wing profile using semi simetris mh30.
to print fuselage is not any special, except front part you need some thickness for motor mount. all fuse part is 1 perimeter (0.4mm) and no infill, some with top/ bottom layer to ease of gluing and add some rigidity.
to print wing you need some attention. 1 perimeter and infil 1.5%. this infill just for manage airfoil curvature. add top and bottom layer to ease gluing and make solid join.
wing part just one side, so you need to copy and mirroring to make other side
CG locate at front wall of spar canal. wing mount to fuselage by 4mm screw.
for glueing, im using uhu all plastics, this glue work very well for thin 3d print part.
i make 2 front (nose) model, shot nose and long nose. long nose will make benefit to manage center of grafity.
setting for plane:
aileron up +- 5mm, and +-5mm down
elevator +- 3mm up, 2mm down
you need set end point to do this.
add exponent 30% or more
my electronic setup:
brushless 2204 ccw 2300kv
tgs propeller 4.75 x 4.75
esc 20A
lipo 850mah 3s
servo 9gr
offcourse you can use your own setup
Similar models
thingiverse
free
Flitetest Tiny Trainer Fuselage by jhallett
...rewall is 3 perimeter and 20 infill. cowling is 3 top, 2 bottom and 10% infill. makes the plane just a bit heavier but not much
thingiverse
free
Aeronaut Triple - MPX Connector conversion kit
...e carefull not to glue the wing to the fuselage.
print in the orientation the stl loads and use supports for the mounting flange.
thingiverse
free
Bix3 Nose by Nevilos
...2200mah 3s battery.
this nose can take a lot of crashes. my first fuselage would end up more broken than this taking a scratch.
thingiverse
free
DIY Foam Glider Wing Holders
...n allows you to shift the cg front or back, before gluing it to the fuselage. they easily print standing on a front or rear face.
thingiverse
free
Modular SciFi Scenery V2 by BoiledMouse
... pieces (you may need to file the tabs down a little to make them fit).
no glue needed for anything.
prints 0% infill, 0 support.
thingiverse
free
Speedy "Red Mini Wing" RC Plane by wersy
....3 layer hight
0.5 width
3 solid bottom layer, spiral vase mode
the bigger fin plate:
3 solid bottom layer
1 perimeter
10% infill
thingiverse
free
Speedy Red Midi Wing by wersy
... in the slicer.
the cylinder must be printed hollow, with only 2 or 3 perimeters.
then you have to re-cut the bushing with a tap.
thingiverse
free
FT arrow fuselage
...fuselage
thingiverse
custom fuselage for ft arrow.
i glued the wing directly to the fuselage with hot glue,
the motor is a 1806.
thingiverse
free
RC Plane
...3d printed parts skysurfer 1400mm wings and stabilizers (or similar motor - i used a2212 1000kv, you can use...
thingiverse
free
Delta Wilde Hummel by wersy
...se no solid bottom/top layers
acces panel brackets: print width 0.5mm, layer height 0.2mm, spiral vase no solid bottom/top layers
Pylon
thingiverse
free
a pylon by rorymace
...a pylon by rorymace
thingiverse
a replicator pylon
thingiverse
free
Pylon by Kellerwichtel
...pylon by kellerwichtel
thingiverse
pylon für mario kart
thingiverse
free
Pylon by trololol
...pylon by trololol
thingiverse
pylon
height 106.5 mm
outer dia. from 15 mm to 70 mm
thingiverse
free
hv pylon by Syzguru11
...hv pylon by syzguru11
thingiverse
hv pylon
thingiverse
free
toy pylon for toycar
...toy pylon for toycar
thingiverse
toy pylon for toycar
thingiverse
free
Protoss pylon with light by rephus
....
print either:
pylon-bottom + pylon-top or
pylon-top-crystal + pylon-bottom-crystal + pylon-top-support + pylon-bottom-support
thingiverse
free
Telecom Pylon by Peeeter
...telecom pylon by peeeter
thingiverse
monotube pylon, multiple parts;
thingiverse
free
Freewing pylon by fredmdbud
...freewing pylon by fredmdbud
thingiverse
basic freewing pylon (designed specifically for the mig-29)
thingiverse
free
high voltage pylon by Syzguru11
...high voltage pylon by syzguru11
thingiverse
high voltage pylon
thingiverse
free
28mm Road Pylon by ISOpod
...28mm road pylon by isopod
thingiverse
basic road pylon.
Racer
thingiverse
free
Bobbin Racer by fastkite
...bobbin racer by fastkite
thingiverse
bobbin racers are low speed, high torque obstacle racers.
thingiverse
free
Racer Cycle by Gangadhar
...racer cycle by gangadhar
thingiverse
racer cycle by ameya [created on 3dtin]
thingiverse
free
F1 Racer by Mbufkin
...f1 racer by mbufkin
thingiverse
f1 racer created by student at trussville midde schol
thingiverse
free
Speed Racer stencil by Longquang
...speed racer stencil by longquang
thingiverse
speed racer stencil
thingiverse
free
Dicey Racers car upgrade by thelibguy
...ken upgrade for the game dicey racers.
for more info on dicey racers, check out:https://www.thegamecrafter.com/games/dicey-racers
thingiverse
free
FIDGET RACER by ahines13
...fidget racer by ahines13
thingiverse
m
thingiverse
free
Speed Racer by WeldingEagle1
...speed racer by weldingeagle1
thingiverse
it is fast.
thingiverse
free
co2 Racer by burnaxel
...co2 racer by burnaxel
thingiverse
car
thingiverse
free
FOOT DRONE RACER by Hopson
...foot drone racer by hopson
thingiverse
pieds pour drone racer... vis et boulons taille 2.5mm
thingiverse
free
racer fpv 250 quadcoptere by sam2302
...racer fpv 250 quadcoptere by sam2302
thingiverse
250 fpv racer