Thingiverse
Printrbot Simple Bed Extension by frederickrelyea
by Thingiverse
Last crawled date: 3 years ago
Enables the Printrbot Simple to use the full width of the bed, extending the width from 100mm to 140mm (+40%).
All holes should be drilled and tapped with a #6-32 tap set. Use 3/4" x 1/2" (1/16" thick) angle aluminum for the front brace, and 3/4" x 1/16" thick aluminum for the rear brace. I used two springs (one inside of the other) for the drive line tensioner.
New cord will be needed for the drive line (I recommend Spectra over Kevlar, as the Kevlar line will frey with use.)
2x 330mm x 8mm smooth rod
5x #6-32 x 3/4" screws (rod clamps and spring anchor)
4x #6-32 x 1/2" screws (rear aluminum bar mounting)
3x #6-32 x 3/8" screws (front 'L' aluminum mounting and drive cord anchor)
12x #6 washers
When printing these parts on the Printrbot Simple, you will need to rotate them 45 degrees to fit in the existing print area.
On the Printerbot Simple, the default bed sizes are x100 y100 z115. Before updating your printer, read the current settings using the M501 command. Then execute the following (to update X to 140 mm):
M211 X140 Y100 Z115
M500
These lines set and write the new bed size to the controller. Confirm the new settings by typing M501.
All holes should be drilled and tapped with a #6-32 tap set. Use 3/4" x 1/2" (1/16" thick) angle aluminum for the front brace, and 3/4" x 1/16" thick aluminum for the rear brace. I used two springs (one inside of the other) for the drive line tensioner.
New cord will be needed for the drive line (I recommend Spectra over Kevlar, as the Kevlar line will frey with use.)
2x 330mm x 8mm smooth rod
5x #6-32 x 3/4" screws (rod clamps and spring anchor)
4x #6-32 x 1/2" screws (rear aluminum bar mounting)
3x #6-32 x 3/8" screws (front 'L' aluminum mounting and drive cord anchor)
12x #6 washers
When printing these parts on the Printrbot Simple, you will need to rotate them 45 degrees to fit in the existing print area.
On the Printerbot Simple, the default bed sizes are x100 y100 z115. Before updating your printer, read the current settings using the M501 command. Then execute the following (to update X to 140 mm):
M211 X140 Y100 Z115
M500
These lines set and write the new bed size to the controller. Confirm the new settings by typing M501.
Similar models
thingiverse
free
Printrbot Simple 1405 18"x6" Print Bed by TechMav
...uminum, to hold a steel plate that will give you roughly a 15 1/2" x 6" print surface, if you upgrade your y-axis also.
thingiverse
free
Ender 3 HDD Motor Spool Holder by Amazing3D
...nd screws)
1 x hdd_ender3_backplate
1 x hdd_motor_holder
1 x hdd_spool_holder
6 x 6-32 machine screws
6 x 6-32 machine screw nuts
thingiverse
free
Optical mount for lens / mirror / prism by dmarett
..." screws
1 6-32 x 3/4" screw (ball mount)
2 1/2" springs with hook ends
4 7/16" x 1/16" aluminum pins
thingiverse
free
High-Capacity 3.5" Hard Drive Adapter Plate for Antec Sonata III Case by Ayo_O
...d on the western digital website, under knowledge base article #9915:
https://support.wdc.com/knowledgebase/answer.aspx?id=9915
thingiverse
free
Printrbot Simple Dial Mount by jhoff
...t screws. if you choose to use set screws, i recommend using a 3/32" drill to bore out the holes so you can get a solid tap.
thingiverse
free
The Kellybow - A Modern Nerf Rainbow Pistol by ahalekelly
...& locknut
trigger pivot screw: 4-40 x 3/8"
grip screw: 10-32 x 1" & nut
2 rear cap screws: m3 x 20mm & nuts
thingiverse
free
Printrbot Simple Anchor for mounting printer by frederickrelyea
...ets for added strength. this new version is slightly taller (0.06") which aligned better with the hardware on my printrbot.
thingiverse
free
Router Lift by edlsmith
...s.
no supports required
if you found this useful, please consider donating to my paypal.me. help cover the time of design.
thanks
grabcad
free
Table brace
...table brace
grabcad
4x: 1/4"-20 x 1" screws and nuts
4x: 8-32 x 1" screws and nuts
thingiverse
free
PrinterBot Simple anchor/Control Panel w/LEDs or switches! by metaled
...nder-lying surface. (could use felt or foam as well.)
printrbot simple front anchor with 5mm holes for mounting 5mm leds and leds
Frederickrelyea
thingiverse
free
Quectel L50 GPS Enclosure by frederickrelyea
...quectel l50 gps enclosure by frederickrelyea
thingiverse
quectel l50 gps enclosure
thingiverse
free
Quadcopter Landing Skid/Gear X525 by frederickrelyea
...ear x525 by frederickrelyea
thingiverse
simple and effective landing skid. doesn't break when landings are less than ideal.
thingiverse
free
Printrbot Simple Y Axis Spring Tensioner by frederickrelyea
...is to eliminate the need to manually tension the drive line. i used two springs, one inside the other to provide enough tension.
thingiverse
free
Printrbot Simple Anchor for mounting printer by frederickrelyea
...ets for added strength. this new version is slightly taller (0.06") which aligned better with the hardware on my printrbot.
thingiverse
free
3DR APM 2.6 Autopilot mounting plate for KK Multicopter Quadcopter replacement by frederickrelyea
...port on the apm). with the original mount, you need to put the telemetry radio on the under side so the usb port is not blocked.
thingiverse
free
X525 Quad Copter Spring Loaded Landing Gear by frederickrelyea
...so i've made a beefed up version. version 5 is the latest...i've also tapered it towards the base to make it look nicer.
thingiverse
free
Y Axis Spring Tensioner - Remix by mh2014
...by mh2014 thingiverse this assembly was inspired by user frederickrelyea in this remix, the wheel uses an aluminum spacer...
Printrbot
thingiverse
free
printrbot gasket by Usernameunavailible
...printrbot gasket by usernameunavailible
thingiverse
a part for printrbots
thingiverse
free
Printrbot Aluminum by Chris_the_Carpenter
...printrbot aluminum by chris_the_carpenter
thingiverse
a redesign of the awesome printrbot, in aluminum.
thingiverse
free
PrintrBot keychain by SuperMaku
...printrbot keychain by supermaku
thingiverse
printrbot keychain. may need to be scaled up.
thingiverse
free
Printrbot foot by aliekens
...printrbot foot by aliekens
thingiverse
add wider feet to a printrbot for improved stability.
thingiverse
free
Printrbot to CNC by mmrrsiam
...printrbot to cnc by mmrrsiam
thingiverse
make your printrbot also a small cnc machine....
thingiverse
free
Printrbot Keychain by jackbivona
...printrbot keychain by jackbivona
thingiverse
printrbot keychain for all you pb customers out there
thingiverse
free
Printrbot+ Nutkeepr by DonaldJ
...printrbot+ nutkeepr by donaldj
thingiverse
clip to retain nut on z-axis threaded rod of printrbot+
thingiverse
free
PrintrBot Tool Caddy by spr_consulting
...printrbot tool caddy by spr_consulting
thingiverse
printrbot tool caddy.
thingiverse
free
Printrbot Sensor Wrench by spr_consulting
...printrbot sensor wrench by spr_consulting
thingiverse
curvaceous printrbot sensor wrench.
thingiverse
free
Spool Holder for Printrbot by doubleAdoubleU
...spool holder for printrbot by doubleadoubleu
thingiverse
spool holder for a printrbot simple metal
Extension
3d_export
$5
extension plug - extension socket
...model. low poly and game ready. with blender files and texture (.png).<br>verts: 424<br>faces: 364<br>tris: 808
3ddd
$1
Moooi, Extension Chair
... стул , вешалка
стулья фирмы moooi, коллекция extension
turbosquid
$300
Bedroom Extension
...
royalty free 3d model bedroom extension for download as skp on turbosquid: 3d models for games, architecture, videos. (1682078)
3d_export
$5
palo extensible
...palo extensible
3dexport
turbosquid
$39
Leg Extension
...ee 3d model leg extension for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1276776)
3d_export
$5
lampe extensible architecte
...lampe extensible architecte
3dexport
lampe extensible architecte maisons du monde
turbosquid
$20
Leg Extension
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
Garage Extension
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Extension cable
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Moooi Extension Chair
...moooi extension chair
3ddd
moooi
http://www.moooi.com/products/extension-chair
Bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
free
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
free
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
Bed
...bed
3ddd
bed , постельное белье , постель
bed
3d_export
$7
bed adairs bed
...rs bed
3dexport
bed adairs bed in modern style. if you want a smoother surface, please turn on turbosmooth in the modifier list.
Simple
turbosquid
$1
Simple goblet (Taca simples)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
simple bench
...simple bench
3dexport
the simple bench which can be used in simple projects or video-games.
3d_export
$5
simple knob
...simple knob
3dexport
simple knob
3d_export
$5
simple handle
...simple handle
3dexport
simple handle
3d_export
$5
simple button
...simple button
3dexport
simple button
3d_export
$5
simple spindle
...simple spindle
3dexport
simple spindle
3d_export
$5
simple wheel
...simple wheel
3dexport
simple wheel
3d_export
$5
simple chair
...simple chair
3dexport
simple blue chair
3d_export
free
Simple room
...simple room
3dexport
here is a simple but beautiful room
3ddd
free
SIMPLE | Кресло
...io cianfarra , simple
производитель area declic дизайн giulio cianfarra коллекция simple