Thingiverse
PowerBlock AA by MadVampy
by Thingiverse
Last crawled date: 3 years, 1 month ago
After designing the other PowerBlock a friend of mine wanted one that had a divider between the two posts to stop any potential arcing between the two posts (he has 12VDC Pos on one side and 12VDC Neg on the other). I redid the original design spacing out the two bonding posts more and adding a dividing wall (anti-arc) between the two posts.
Below is the link to the other PowerBlock and also the same info that applies to this one.
http://www.thingiverse.com/thing:1981937
I designed it in 123D Design and after printing it I went and bought some 1/4" stainless steel hardware (1/4" X 3/4" bolts, small 1/4" flat washers, 1/4" nuts). I pushed them in and then held the bolt in place with a nut, I then used 5 min epoxy to fill in the space behind the bolt head. This not only holds the bolt in place but it also electrically insulates the bolt from any metal it may be attached to. The bolt is a snug fit so there will not be any twisting of it inside the printed plastic.
Below is the link to the other PowerBlock and also the same info that applies to this one.
http://www.thingiverse.com/thing:1981937
I designed it in 123D Design and after printing it I went and bought some 1/4" stainless steel hardware (1/4" X 3/4" bolts, small 1/4" flat washers, 1/4" nuts). I pushed them in and then held the bolt in place with a nut, I then used 5 min epoxy to fill in the space behind the bolt head. This not only holds the bolt in place but it also electrically insulates the bolt from any metal it may be attached to. The bolt is a snug fit so there will not be any twisting of it inside the printed plastic.
Similar models
thingiverse
free
Power Block by MadVampy
... from any metal it may be attached to. the bolt is a snug fit so there will not be any twisting of it inside the printed plastic.
thingiverse
free
Tronxy X5S Motor Mount Micro Adjust by OatMeehl
...t one for the "x" axis, just mirror the "y mount body" in your slicer. all the other parts should work as is.
thingiverse
free
Yet another re-winder for XYZ DA Vinci printer updated by buzzerco
...l, and use it to wind filament onto the spool.
also note in the diagram how to wind from one spool to the other to avoid twisting
thingiverse
free
Microsoft Lifecam Mount by njb5102
...n place.
there also is a 2020 mount included.
hardware needed:
m3x16 bolts
m3 nuts
optional hardware:
1 - m4x20 bolt
1 - m4 nut
thingiverse
free
Pipe coupler 1" by Buildituniversity
...olds the nut in place. i'm using this to attach two chrome kitchen racks to each other for stability and consistent spacing.
thingiverse
free
1/2" Schedule 40 PVC swivel joint
...designed with a little slop between the part and the pvc. you could easily drill a hole and bolt or screw the part into the pvc.
thingiverse
free
knob for 1/4" bolt by marmil
...: epoxy the bolt (or nut) in place if the knob will be regularly completely unscrewed so you don't loose your bolt (or nut).
thingiverse
free
Roller Hold-Down by Perkinje
...o the upper assembly had to be printed in two parts. i've included files for printing the upper assembly as one or two parts.
thingiverse
free
Oversized Bicycle Saw Guide for Carbon Composite Forks by bcrop
... blades, i found that the larger one works better for my purposes. still a steady hand and good eye are required for a clean cut.
thingiverse
free
Vivo Monitor stand VESA clamp by 1bigpig
... 1 length plus 2 nuts.
you can also use 6mm x 40mm bolts and nuts for the clamp and 4mm x 25mm bolts and nuts for the vesa mount.
Powerblock
thingiverse
free
Powerblock Bracket by Volkhard
...derneath my desktop.
i created it in fusion 360, and used meshmixer to create the .stl file. i printed it on xyz da vinci mini w.
thingiverse
free
PowerBlock by Limeguy88
...erblock by limeguy88
thingiverse
nothing more then a miniature powerthingie...
i used it for my brave little toaster diorama...
thingiverse
free
PowerBlock Dumbbell Replacement Pin by Aslabic
...powerblock dumbbell replacement pin by aslabic
thingiverse
replacement pin for broken powerblock dumbbell weight selector pin.
thingiverse
free
PowerBlock Situp Adapter by TaylorSharpeSS
...-up weight.
after printing, i added two layers of 3/4" foam tape to each adapter: https://www.mcmaster.com/catalog/93275k122
thingiverse
free
PowerBlock Weight Holder by dangerousdavebot
...t need support material. also if you're slicing with cura, consider using the ironing features for an extra sleek upper face.
thingiverse
free
Raspberry Pi 3 (B/B+), Pi 2 B, and Pi 1 B+ case with PowerBlock support by Gary_BBGames
...
a raspberry pi 3/b/+ case with hot-rod style cut outs for a powerblock from petrockblock, and holes for a switch and power led.
thingiverse
free
Remixed Pi 3 NES case bottom with Powerblock by LaneLibraryTechCenter
... micro usb cap and made it with ninjaflex filament, then stuck it over the original power adapter location of the raspberry pi 3.
thingiverse
free
Power block holder for HyperCube Evolution frame by Alderoth
...alderoth thingiverse these are used to hold a aliexpress powerblock on the hypercube evolution frame. it has been designed...
thingiverse
free
RetroPie Custom Console Case by smartroad
...asking for a case that could also take their powerblock as well. so i designed the case to accommodate...
Madvampy
thingiverse
free
CapNRing by MadVampy
...to allow for that. i'll add both the one with and without the o-ring holder. printed this in abs (as i do with all my prints)
thingiverse
free
RamTray by MadVampy
...lined up pretty good (might have to tweak yours depending on the material you use to print it).
not much more to say on this one.
thingiverse
free
Hanger by MadVampy
...cal surface like a wall or such. went with 100% infill for strength but if your object isn't heavy you can reduce the infill.
thingiverse
free
Handle by MadVampy
... 100% infill to make it strong for when i was breaking them apart.
please feel free to make any changes to suit your needs. enjoy
thingiverse
free
Pokemon Stand by MadVampy
...ign. hope you enjoy it! post comments and also like it if you feel so inclined. also if you do a print share it with others here.
thingiverse
free
Power Block by MadVampy
... from any metal it may be attached to. the bolt is a snug fit so there will not be any twisting of it inside the printed plastic.
thingiverse
free
MagSDHolder by MadVampy
...f you liked the design and feel free to comment also.
magnets i used: https://www.apexmagnets.com/15mm-diameter-x-5mm-thick-disc
thingiverse
free
Blind Holders by MadVampy
... blind. i laid them on their backs so there is no need for rafts or support.
this is my first design so go easy on me. lol enjoy!
thingiverse
free
Dead Pool Buckles by MadVampy
...now these were measured and printed for the size deadpool that i did you may have to adjust the scaling to fit the one you print.
thingiverse
free
Big Handle by MadVampy
...liers to remove it. this is a large handle measuring 4" x 6" so you can scale it as you need.
modify it as you see fit.
Aa
3d_export
$12
AA
...aa
3dexport
aa
3d_export
$10
aa
...aa
3dexport
aa
turbosquid
free
AA-1 to AA-12 complete collection
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
GAZ-AA
...
turbosquid
royalty free 3d model gaz-aa for download as max on turbosquid: 3d models for games, architecture, videos. (1230089)
turbosquid
$45
AA Gun
...uid
royalty free 3d model aa gun for download as obj and fbx on turbosquid: 3d models for games, architecture, videos. (1301154)
turbosquid
$29
AA Battery
... 3d model aa battery for download as obj, fbx, blend, and stl on turbosquid: 3d models for games, architecture, videos. (1468989)
turbosquid
$29
AA Battery
...ee 3d model aa battery for download as max, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1520726)
turbosquid
$5
AA battery
... 3d model aa battery for download as blend, dae, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1605047)
turbosquid
$15
AA Batteries.max
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
GAZ AA
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.