Thingiverse
Powder trickler by Multihjalle
by Thingiverse
Last crawled date: 3 years, 1 month ago
A simple gun powder trickler with 2 different risers for different powder scales , You have to use a 8 mm pipe with internal thread for the powder to travel easy to your scale but i reckon it will work even without the thread but slower. this is for now a work in progress so i have not measured the pipe for the hole inside the trickler that you have to grind , but i hope that if you have the skills to make ammo the tubing is a simple diy .take a tube between 8 and 12 cm ( your choice) glue the knob make 2 washers and glue one close to the knob stick it in the trickler and mark a hole inside, grind a hole for the powder to fall in the pipe , assembly the pipe and glue the other washer and your done
Similar models
thingiverse
free
Powder trickler deluxe by Multihjalle
...ssembly the pipe and glue the other washer and your done. if someone needs a riser for the trickler i will make one for them soon
thingiverse
free
RCBS Powder Trickler Knob by Eighty6SVO
...e-on so adjust the scaling to get yours to fit snugly onto the trickler tube so that the knob doesn't slip when it is turned.
thingiverse
free
KITCHEN PAPER INDUSTRIAL SPINDLE / SPOOL HOLDER by JAUYEB
...t my other designs:https://www.thingiverse.com/jauyeb/designs
make my day by push like button if you like it and post your makes!
thingiverse
free
Stand for powder trickler by BlackJeep
...al powder trickler high enough to dispense directly onto a rcbs scale.
opening is 47mm
raises trickler 10mm
reloading
ammunition
thingiverse
free
NEMA 17 Powder Trickler by NJ_v_N
...rated powder trickler.
designed as part of an arduino project to make a auto powder measure.
it uses a lee powder measure hopper.
thingiverse
free
Glue Tube Small Nozzle
...ook a few tries to get right, the best fit is with a 12mm hole, 1.25mm thread pitch. the hole for the glue is approximately 1.5mm
thingiverse
free
Pokeball by That_sweet_1_fps
... part with the circle is aligned. then you glue the button on the circle. after printing the stick, you place it inside the holes
thingiverse
free
Tactical bolt knob M8 thread by statsminister
...
modeled and printed a bolt knob for my remington 700. i grinded and threaded the stock bolthandle with a m8 thread. works great!
thingiverse
free
Dremel Attachment by Karlosek
...e pieces together.
v2 is the same, with dremel threaded nut as part of design. i still have to test how square it sits on dremel.
thingiverse
free
Pipe Clamp 110mm by Bede98
...ide at the top.two nuts and washers with about 50mm of the threaded rod were used on the side to clamp the whole thing on a pipe.
Multihjalle
thingiverse
free
Fatshark 600tvl manual tilt by Multihjalle
...an be mounted almost everywhere on the upside an under also. i use the sticky pads for heli gyro to glue them on the fpv platform
thingiverse
free
ir mount by Multihjalle
... and 250 would probably go , 160mw is what i am using now but i will try stronger for longer range and illumination in the future
thingiverse
free
Fatshark 600tvl fpv camera mount by Multihjalle
...hed easy and fits nice . a protection tube around the lens to protect the camera lens and body when crashing. feel free to modify
thingiverse
free
Case Neck Graphiter by Multihjalle
...reloading bench or some other place , made this one when my forster brake up but didnt want to make a straight copy of that one .
thingiverse
free
Powder trickler deluxe by Multihjalle
...ssembly the pipe and glue the other washer and your done. if someone needs a riser for the trickler i will make one for them soon
thingiverse
free
Fox / Coyote Caller by Multihjalle
...t. there are plenty of pictures just google it and you know how to cut it . hope this is what your succes need`s regards peter
thingiverse
free
Fatshark 600tvl and immersion 600mw 5.8 fpv pod by Multihjalle
... , one short model if you want a tight set and one that is 20 mm longer i usually cut the wires and solder them for a clean setup
Trickler
thingiverse
free
Powder Trickler by NJ_v_N
...powder trickler by nj_v_n
thingiverse
a reloading powder trickler, roughly copied from a commercial one.
thingiverse
free
Stand for powder trickler by BlackJeep
...al powder trickler high enough to dispense directly onto a rcbs scale.
opening is 47mm
raises trickler 10mm
reloading
ammunition
thingiverse
free
Hornady’s Powder Trickler Funnel by commanderbeatle2
...hornady’s powder trickler funnel by commanderbeatle2
thingiverse
just a funnel for hornady’s powder trickler.
thingiverse
free
Powder Trickler by equiFX
...powder trickler by equifx
thingiverse
trickle this powder!
easy print!
thingiverse
free
Dynamic powder trickler by Grahn
...irst customizeable powder trickler!
perhaps my whole collection of reloading equipment is to your liking ?
dynamic reloading gear
thingiverse
free
RCBS Powder Trickler Knob by Eighty6SVO
...e-on so adjust the scaling to get yours to fit snugly onto the trickler tube so that the knob doesn't slip when it is turned.
thingiverse
free
NEMA 17 Powder Trickler by NJ_v_N
...rated powder trickler.
designed as part of an arduino project to make a auto powder measure.
it uses a lee powder measure hopper.
thingiverse
free
Powder trickler deluxe by Multihjalle
...ssembly the pipe and glue the other washer and your done. if someone needs a riser for the trickler i will make one for them soon
thingiverse
free
Powder Trickler "Tank" by fenofun
...ed to find carbon or aluminum tube 6.5mm od, ~5mm id and ~100mm length.
https://www.youtube.com/watch?v=kga8uno5rxu&feature
Powder
archibase_planet
free
Powder-box
...powder-box
archibase planet
powder-box powder-case puff-box
powder-box n150112 - 3d model (*.3ds) for interior 3d visualization.
3d_export
$5
Powder pistol
...powder pistol
3dexport
turbosquid
$12
Powder Room
...3d model powder room for download as 3ds, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1392103)
turbosquid
$10
Juice Powder
... 3d model juice powder for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1493717)
turbosquid
$4
Anis and powder
... model anis and powder for download as lwo, fbx, stl, and obj on turbosquid: 3d models for games, architecture, videos. (1626302)
turbosquid
$6
powder-box
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
archive3d
free
Powder-box 3D Model
...-box powder-case puff-box
powder-box n150112 - 3d model (*.3ds) for interior 3d visualization.
3d_export
$5
barrel powder
.... ready for game. tested on unreal engine 4.<br>texture resolution 2048 x 2048 png: basecolor, metallic, normal, roughness.
3d_export
$5
zuzi powder swivel chair
...zuzi powder swivel chair
3dexport
zuzi powder swivel chair kare design
turbosquid
$40
Nadhif powder bag
...
royalty free 3d model nadhif powder bag for download as max on turbosquid: 3d models for games, architecture, videos. (1155016)