Thingiverse
Pot stirrer by dgm3333
by Thingiverse
Last crawled date: 3 years, 1 month ago
This is parametric pot stirrer.
It has a 12V motor attached to the top of the shaft (10RPM from ebay) which rests on the top of the pot. It runs off an adaptor, but could easily run off batteries depending on how much power is required to run it.
To enable quick and easy detachment of the motor from the stirrer it uses a modified version of my Parametric spider coupling inspired by the Turbo Mixer. The spider is not required, as with one-way rotation backlash is not an issue
The default current stirrer is designed for an 11cm flat base pot, but this can be easily adjusted in the SCAD file.
EDIT 16/6/13:
New SCAD uploaded with a few more options for the hub attachment.
My initial version distorted while cooking porridge, and the blades were too close, so tended to clog with a range of things (rice,lentils,etc) so I've spaced them out a bit more.
I'm unsure whether I'll be able to change the profile to stop the heat-distortion, or whether I'll just have to cast it in something a bit more heat-proof or try nylon printing...
I covered the plastic overhanging the edge of the pot with Kapton, and that survived fine.
It has a 12V motor attached to the top of the shaft (10RPM from ebay) which rests on the top of the pot. It runs off an adaptor, but could easily run off batteries depending on how much power is required to run it.
To enable quick and easy detachment of the motor from the stirrer it uses a modified version of my Parametric spider coupling inspired by the Turbo Mixer. The spider is not required, as with one-way rotation backlash is not an issue
The default current stirrer is designed for an 11cm flat base pot, but this can be easily adjusted in the SCAD file.
EDIT 16/6/13:
New SCAD uploaded with a few more options for the hub attachment.
My initial version distorted while cooking porridge, and the blades were too close, so tended to clog with a range of things (rice,lentils,etc) so I've spaced them out a bit more.
I'm unsure whether I'll be able to change the profile to stop the heat-distortion, or whether I'll just have to cast it in something a bit more heat-proof or try nylon printing...
I covered the plastic overhanging the edge of the pot with Kapton, and that survived fine.
Similar models
thingiverse
free
Thermolyne Cimarec Stirrer Hotplate Replacement Knob by knowledgecravings
...nt part is primitive, but functional, i just wish i had grey filament at the time i made it so it wouldn't stand out so much.
thingiverse
free
Thermometer holder for Mendel - Parametrized. by Nudel_P
...openscad, so you can easily adapt it for other similar equipment. i use mine to read the temperature of...
thingiverse
free
Parametric LED Candle Holder by holgero
...ird holder (holder3.scad) uses my own flickering led implementation with a pic12f508 (https://github.com/holgero/picflickerleds).
thingiverse
free
parametric bit rack
...e i wanted. also wanted it to be parametric so i could easily extend it in whatever dimension to group together other-sized bits.
thingiverse
free
Parametric spider coupling by modilion
...s allows for multiple coupling legs while this simple scad is limited to dual leg layouts.
both bore holes have individual sizes.
thingiverse
free
Parametric e liquid/paint stirrer by deckingman
...verse customiser" works but if you download open scad (which is free) and import the scad file, you'll have no problems.
thingiverse
free
Parametric brushed micro quadcopter for lulfro, alienwii, etc by drkow
...lulfro.
updated june 9 2016 with the latest version i'm flying (lulfro_quad3.stl). it's less parametric, but more robust!
thingiverse
free
Extended Play U-joint by bjcomp2384
...d on top, allowing for better clearance, and more movement, when connected to my trolling motor, so i can drive from the cockpit.
thingiverse
free
Stepper motor speed control box. by Galane
...y crookedly mounted heat sinks.
you'll probably have to push the big diode a bit towards the knob side to get the top to fit.
thingiverse
free
eBellows - Electronic Fireplace Bellows by vik
...dle and battery holder stuck on, but i've improved the parametrics a bit.
if i run it off 12v it beats my 110mm forge blower!
Dgm3333
thingiverse
free
Skate Bearing Holder by dgm3333
...bearing holder by dgm3333
thingiverse
a couple of different versions for holding standard skate bearing (id 8mm, od 22mm, w 7mm)
thingiverse
free
Basic LM8UU Clamp by dgm3333
...the baseplate.
although no longer using the original code, or even looking much like them, the ancestors provided my inspiration.
thingiverse
free
Centre Finder by dgm3333
...the openscad file is parametric, so you can adjust dimensions to suit your need (including offset for blade/scribe/pen diameter).
thingiverse
free
Parametric Z and X axis endstops by dgm3333
... are a couple of enhanced end-stop holders. i found the prusa v1 endstops i had originally wobbled, whereas these are rock-solid!
thingiverse
free
David's Ring Extruder by dgm3333
...extra bearings to support the rings.
-probably motor drive would be better more centrally to better support the ring
-and more...
thingiverse
free
Yet another 360 degree extruder fan by dgm3333
... (even worked on my badly calibrated printer).
edit: a few problems have been identified (see below) which are being worked on...
thingiverse
free
Anti-Warping Walls by dgm3333
...sure they didn't get too close.
possibly some little handles to assist with extracting them from under a moving x-carriage.
thingiverse
free
Bed Levelling Kit with Calculator by dgm3333
...it: 23/10/14: updated the spreadsheet to improve accuracy and simplify levelling with caliper/depth gauge for the 3-support sheet
thingiverse
free
X or Y axis belt clamp with tensioning ram by dgm3333
...ve one on my y belt, so not yet released in the wild...
edit: 11/6/13: replaced scad file to correct error placing screw holes.
Stirrer
turbosquid
$5
French Press with 2 Mugs and Stirrer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$125
coffee cup lid paper package sachet foil bag stirrer
...normal (directx)<br>geometry:<br>- units: centimeters<br>- ngons: 0<br>- vertex with more than 5 edges: 0
3d_export
$12
wooden coffee stirrers package set
...; x 7.15" x 1.04"<br>- model parts: 2<br>- material count: 2<br>- xform: yes<br>- boxtrick: yes
3d_export
$19
paper coffee cup with lid sugar package wooden stirrer
...; x 7.08" x 4.34"<br>- model parts: 4<br>- material count: 4<br>- xform: yes<br>- boxtrick: yes
3d_export
$90
distillery equipment
...of glasses<br>six test tubes in various sizes<br>various straws and stirrer<br>rubber tubing<br>various metal stands for the schlenks and retorts<br>one cup<br>and...
3dfindit
free
Hydraulic stirrers
...hydraulic stirrers
3dfind.it
catalog: arag
thingiverse
free
Stirrer/Mixer by JetEn
... up etching pcbs by mixing liquid at low speed.
how it work ? a pcb lies on the bottom of the tank and the stirrer works over it.
thingiverse
free
Epoxy Stirrers by JohnDoe_1
...epoxy stirrers by johndoe_1
thingiverse
never liked the popsicle stick stirrers.
these give me finer control.
thingiverse
free
Coffee Stirrer Holder by Mach3tte
...coffee stirrer holder by mach3tte
thingiverse
coffee stirrer holder.
thingiverse
free
Gibraltar Cocktail Stirrer by cmonkey
...gibraltar cocktail stirrer by cmonkey
thingiverse
a cocktail stirrer modelled after the flag of gibraltar.
Pot
3d_export
$5
pot
...pot
3dexport
pot
3d_export
$9
pot
...pot
3dexport
design of pot
archibase_planet
free
Pot
...pot
archibase planet
pot coffee pot kitchen ware coffee
pot coffee n231210 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Pot
...pot
archibase planet
coffee-pot coffee pot kitchen ware
coffee pot - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Pot
...pot
archibase planet
pot jug mug
pot - 3d model for interior 3d visualization.
archibase_planet
free
Pot
...pot
archibase planet
pot jug mug
pot 2 - 3d model for interior 3d visualization.
archibase_planet
free
Pot
...pot
archibase planet
pot jug mug
pot 3 - 3d model for interior 3d visualization.
archibase_planet
free
Pot
...pot
archibase planet
pot bowl
pot - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Pot
...pot
archibase planet
jar can pot
pot - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Pot
...pot
archibase planet
can jar pot
pot - 3d model (*.gsm+*.3ds) for interior 3d visualization.