Similar models
cg_trader
$6
Postit wire
...postit wire
cg trader
postit wire
thingiverse
free
Postit and pencil holder by adilsonth
...postit and pencil holder by adilsonth
thingiverse
a holder for postit and pencil.
thingiverse
free
Pencilcup With Postit Holder by Emmellilla
...pencilcup with postit holder by emmellilla
thingiverse
a pencilcup with postit holder :)
grabcad
free
Spiral of Postit Notes
...spiral of postit notes
grabcad
this is a model of postit notes in a spiral pattern
cg_trader
$5
Postit Sticky Note Collection
...postit sticky note collection
cg trader
postit notes made for any use!
thingiverse
free
PostIt base and organizer by i3Dsd
...tit base and organizer by i3dsd
thingiverse
a friend asked for something to hold postits, pens and clips organized. there you go
thingiverse
free
Tiny PostIt Box by satanasinc
...anasinc
thingiverse
tiny postit box for 50x40mm post-its.
easy an fast print
please upload pictures of your prints and comments.
3dwarehouse
free
Post-It Flags
...bow and more! #3dchallenge8 #3m #bookmarks #desktop #flags #postit #postit_flags #postits #stationary #tiny #tiny_things #yosofun
3dwarehouse
free
Peroukes postit
...peroukes postit
3dwarehouse
modeled with building maker
thingiverse
free
POST IT CASE by kot1759
...post it case by kot1759
thingiverse
postit case
no support
Kjkwat
thingiverse
free
Cable protect by kjkwat
...y kjkwat
thingiverse
protect bends on cables.
helps keep the isolation on cables not to be broken.
could prevent short circuits.
thingiverse
free
Talon nano 4s lipo holder by kjkwat
...talon nano 4s lipo holder by kjkwat
thingiverse
4s lipo holder for talon nano.
thingiverse
free
cable tie self adhesive base by kjkwat
...cable tie self adhesive base by kjkwat
thingiverse
cable tie self adhesive base
just add self adhesive tape.
thingiverse
free
Falcon 250 horizontal antenna cover by kjkwat
...unbreakable" antennas.
flip the circuit board for the fpv.
after demolish 3 standard antennas, ive got a little bit tired :)
thingiverse
free
Falcon 250 flexible landing gear by kjkwat
...the landing field with a bigbarabooom, this could save your drone from breaking.
yes, i have tried it quite a few times allready.
thingiverse
free
SANWU® Bluetooth Audio Receiver Digital Amplifier Board With USB Port TF Card Slot Decoding Play by kjkwat
...audio receiver digital amplifier board with usb port tf card slot decoding play by kjkwat
thingiverse
simple holder for bt chip
thingiverse
free
Protection Camera FPV Super Mini 25mW Eachine TX01 / TX02 200mw by kjkwat
...giverse
camera protection
eachine tx03 ntsc super mini 0/25mw/50mw/200mw switchable aio 5.8g 72ch vtx 600tvl 1/3 cmos fpv camera
thingiverse
free
Falcon 250 red back light by kjkwat
...e single 100 ohm resitor 1/4 w conected to positive serial array.
all conected to the left red light emitting diods on the drone.
Postit
3ddd
$1
аксессуары для ванной ArtCeram Postit
...га
моделировалось по каталогу, геометрия и размеры точные, существуют в черном и белом вариантах, туалетная бумага из эвермоушена
3d_ocean
$1
Post-it
...note notebook notepad notes pad paper post it post-it postit simple a cool post-it setup to render your ideas/tasks...
thingiverse
free
Postit and pencil holder by adilsonth
...postit and pencil holder by adilsonth
thingiverse
a holder for postit and pencil.
thingiverse
free
Pencilcup With Postit Holder by Emmellilla
...pencilcup with postit holder by emmellilla
thingiverse
a pencilcup with postit holder :)
thingiverse
free
PostIt base and organizer by i3Dsd
...tit base and organizer by i3dsd
thingiverse
a friend asked for something to hold postits, pens and clips organized. there you go
thingiverse
free
Tiny PostIt Box by satanasinc
...anasinc
thingiverse
tiny postit box for 50x40mm post-its.
easy an fast print
please upload pictures of your prints and comments.
thingiverse
free
PostIt-Organizer by falau
...postit-organizer by falau
thingiverse
print in place with skirt for good materialflow on first layer.
thingiverse
free
postit on the back (NSFW)
...postit on the back (nsfw)
thingiverse
changes from i havent seen to 3d colorprintable
thingiverse
free
Postit Dispenser by SPLA
...postit dispenser by spla
thingiverse
post-it dispenser
materials : spla 1.75 filament (heat-resistance pla filament)