Thingiverse
Plywood Air Filter by MBCook
by Thingiverse
Last crawled date: 3 years ago
I built zgbot's air filter for my Thing-o-Matic during the machine's build process. I made it to sit on top of the machine, but after about 6 months of being moved around the duct tape started to come loose. Between that and a circular saw I hadn't had a chance to use I decided to make a version out of plywood.
It takes a square cabin air filter about 8"x.75"x1", which I believe is used on Toyota and Lexus cars such as the RX 350. I'm not really sure because I just bought one from an auto parts store that looked like I could build something around it and I never really paid attention. The filter I bought has activated carbon in it to help with the smell.
The air filter goes in the top, and sits on the edges of the bottom half. It's actually a big pain to get in there so if I had it to do over, I'd make one of the side panels on the top section come off (instead of the lid) and slip the filter in that way.
There are 2 80mm fans on top, which make a little more noise (and push more air) than I'd like. The next time I'm doing some internal work, I intend to move them from 12v to 7v so they'll slow down. I've got a simple switch on the line so I can turn them on and off, and I used a barrel plug from RadioShack so I can disconnect the filter and remove it.
The top is a little short, just enough to be able to hang the LCD controls off the front of the machine. The back of the filter sits on the back lip of the ToM. This way I didn't have to put a cutout in for the Z motor. On the sides, I sanded out little channels to be able to fit over the M3 bolts on the top of the machine.
The base section is 3" tall, which was just enough so that the filament drive wouldn't hit the bottom of the filter when at max Z. With the new MK7s, it looks like it could be reduced almost all the way. As it is though, there would be enough room on the front panel of the base section to embed an LCD and control pad, which could look pretty neat.
All measurements are in inches (because I don't seem to own a metric ruler or tape measure), and should more or less correspond with what I built. It's designed for 1/4" plywood. The panels are secured together with brads through the ends (into holes I pre-drilled with a 1/32" or 1/64" bit), and I glued and nailed some 3/4" wood strips in the corners to provide extra support. The top lid is simply screwed on into tapped holes in the extra wood strips. I believe, all together, I used less than half a sheet of plywood.
I've been using it for a few weeks now, and it works quite well. Having the filament feed straight through the top has worked out quite well. It requires punching a hole in the air filter, but it means that it can drop straight down into the extruder.
It takes a square cabin air filter about 8"x.75"x1", which I believe is used on Toyota and Lexus cars such as the RX 350. I'm not really sure because I just bought one from an auto parts store that looked like I could build something around it and I never really paid attention. The filter I bought has activated carbon in it to help with the smell.
The air filter goes in the top, and sits on the edges of the bottom half. It's actually a big pain to get in there so if I had it to do over, I'd make one of the side panels on the top section come off (instead of the lid) and slip the filter in that way.
There are 2 80mm fans on top, which make a little more noise (and push more air) than I'd like. The next time I'm doing some internal work, I intend to move them from 12v to 7v so they'll slow down. I've got a simple switch on the line so I can turn them on and off, and I used a barrel plug from RadioShack so I can disconnect the filter and remove it.
The top is a little short, just enough to be able to hang the LCD controls off the front of the machine. The back of the filter sits on the back lip of the ToM. This way I didn't have to put a cutout in for the Z motor. On the sides, I sanded out little channels to be able to fit over the M3 bolts on the top of the machine.
The base section is 3" tall, which was just enough so that the filament drive wouldn't hit the bottom of the filter when at max Z. With the new MK7s, it looks like it could be reduced almost all the way. As it is though, there would be enough room on the front panel of the base section to embed an LCD and control pad, which could look pretty neat.
All measurements are in inches (because I don't seem to own a metric ruler or tape measure), and should more or less correspond with what I built. It's designed for 1/4" plywood. The panels are secured together with brads through the ends (into holes I pre-drilled with a 1/32" or 1/64" bit), and I glued and nailed some 3/4" wood strips in the corners to provide extra support. The top lid is simply screwed on into tapped holes in the extra wood strips. I believe, all together, I used less than half a sheet of plywood.
I've been using it for a few weeks now, and it works quite well. Having the filament feed straight through the top has worked out quite well. It requires punching a hole in the air filter, but it means that it can drop straight down into the extruder.
Similar models
thingiverse
free
Nespresso Machine Holder by scherle
...the small holes are for screws.)
it's screwed down (or glued) to the counter and the machine sits inside the frame. perfect!
thingiverse
free
CTC Sunken LCD Bezel by jartz
... the bottom cover plate needs to be notched out to clear the lcd, which sits about 15mm lower than before. see pics for details.
thingiverse
free
Fish Tank Lid Risers by Coreybugdolan
...ave a 5" gap in the middle of the long side of a standard 15 gallon tank. they slip (quite nicely) onto the top of the tank.
thingiverse
free
Arduino Uno R3 Case by Proxy303
..., and each section is identical to the individual files.
this is free to use. feel free to remix this, just be sure to credit me.
thingiverse
free
Air Compressor Filter Wall Mount by slipshft
...oversize. also, keep in mind that any acrylic based moisture bowl will expand under pressure (don't make the hole too small).
thingiverse
free
IKEA Lack Enclosure HEPA Air Scrubber by brawfx
...ts that twist on and are held by the 4 tabs on the filter housing. it's mostly friction fit, but it works well enough for me.
thingiverse
free
LEGO TECHNIC Panel/Base by AdamWiddow
...e. if printing in fdm i would recomend printing them flat. it might warp a little but with a well tuned machine it should work.
thingiverse
free
Vitamix Tamper Adapter Saver by wabbitguy
...s well so two tampers in one.
printed in tpu so it's flexible and since it sits above the lid, food safe isn't a problem.
grabcad
free
TartsVoltageSensorCase
... help dissipate heat. i have not put it into use yet so i'm not positive it will have enough air flow but i believe it will.
thingiverse
free
Modified Lid for Jack o lantern pumpkin for battery tea light by mouserunner by Sniffynose
...ng around or falling off, this adds an inner base that fits into the top slot of the pumpkin so it won't slide off so easily.
Mbcook
thingiverse
free
Kitten by JanEriKKa
...thingiverse this is a remix of thing 12694 by mbcook the voronoi pattern was created using the instructions found...
thingiverse
free
Squirrel Silhoutte AKA: Travel Squirrel by LabsOfCognitiveNeuroscience
...the profile. special thanks to the original model creator mbcook as this is a work of beauty that i...
thingiverse
free
Squirrel Pen Holder by relicae
...holder by relicae thingiverse a remix of squirrel by mbcook as pen holder for the office. just added a...
thingiverse
free
cute squirrel drip tip by gallowraven
...thingiverse this is a standard 510 drip tip with mbcook#39;s squirrel on it. i am still working on getting...
thingiverse
free
LM6UU Quick Change Build Platform for ToM by MBCook
...fit just fine. after installing linear bearings on my bot i decided i didn't like the noise, so never ended up printing this.
thingiverse
free
Apparently Impossible Cube Plate by MBCook
...need for a fully assembled cube.
included is the stl you'll need, as well as the ultra-basic openscad file i used to make it.
thingiverse
free
Odyssey Bumper Fix by MBCook
...ong glue bond), a hole in the middle (to replace the screw hole that broke), and a little side piece to match the existing lines.
thingiverse
free
Cage with working gate by MBCook
...on to handle it.
the cage is the biggest thing my thing-o-matic has ever made. i designed it to basically max out the build area.
thingiverse
free
Kitten by MBCook
...fixed minor issues (such as flattening the base) so i could print it out.
[1] http://shapes.aim-at-shape.net/viewgroup.php?id=270
Plywood
3ddd
$1
Plywood Chair
...тор: чарльз эймс (конструктор)
место происхождения: сша
дата производства: около 1950
период: 1940-1949
материалы: дерево, металл
3ddd
$1
IKEA SODERHAMN
...height: 83 cm product description frame three-seat section: frame: plywood fibreboard, moulded beech plywood, beech veneer, steel, felt, solid...
3ddd
$1
Thonet S 64 Pv
...upholstered armchair, seat and back padded over, seat moulded plywood with 30mm cold foam, seams with black synthetic welt,...
3d_export
$15
Wooden panel Subberjean 3D Model
...wooden panel subberjean 3d model 3dexport panel wooden plywood wood classic wall room interior 3d vray ethnic decoration...
3ddd
$1
Milo Mobile washbasin and Mirror
...milo milo mobile washbasin 500*500*850 mirror 2000*500*30 material: water-resistant plywood tempered glass designer: alessandro lenarda (italy) умывальник (мобильный, передвижной)...
3ddd
$1
Fretwork Chest-Pearl Essence
...or french dovetail construction, for years of problem-free use. plywood drawer bottoms are attached to plywood drawer sides for...
3ddd
$1
SWIVEL CHAIR SOHO SOFT TIN
...material: backside: aluminium with antique finishing, density 35kg/m³, frame: plywood seat cover: bycast - polyurethan upholstery: pu foam, base:...
3ddd
$1
plywood collection by hristo stankushev
...d bookcase.http://evis-design-home.blogspot.ca/2013/07/plywood-collection-by-hristo-stankushev.html
max2014/fbx, v-ray
3ddd
$1
The J Table
...3ddd j-table , horm j-table from horm.it, bleached beech plywood shelf leg and white lacquered top. i included all...
3ddd
$1
Andrew Tye / Matrix Table
...large: 43.31"w x 31.5" d x 10.43"h materials: base: plywood top:...
Filter
3d_ocean
$15
Studio HDRi 010
...may use the provided .jpg version that has been filterd with a natural film response algorithm for a much...
3d_ocean
$15
Studio HDRi 003
...may use the provided .jpg version that has been filterd with a natural film response algorithm for a much...
3ddd
$1
Phase Design Ballot Box tables
...tables 3ddd журнальный , ballot phase design ballot box tableshttp://www.phasedesignonline.com/content/design/families/?filterballot-box-family ...
3d_ocean
$6
Energy Bottle
...is divided into 3 parts: the bottle bottom, a filter in the middle, and bottle caps. bottles are polygon...
3d_ocean
$2
Wire mesh
...wire mesh 3docean aluminium brass chain chainlink copper fence filter link mesh metal screen sieve strainer syth wire a...
3d_ocean
$19
Bodum Coffee Press
...beverage bodum cafe cafetiere cappuccino coffee maker cup detailed filter foam french press glass highpoly hot jug kitchen latte...
3d_ocean
$12
Aquarium Water Filter
...
an inside aquarium filter, with no textures. materials, render setup, lighting are not included. 10 650 poligons without smooth.
3d_ocean
$4
Air filter
...ormal texture applied. the texture comes in .tif format. for other cool stuff check out my sales. don’t forget to rate and enjoy!
3d_ocean
$9
Cigarettes and Ashtray
...cigarette (gold logo/filter wrap, silver logo/filter wrap, just logo/no filter wrap). two variations for the filter material are included...
3d_ocean
$1
Cigarette Butts Seamless Tiling
...cigarette cigarette end cigarettes compressed dirty disgusting drug filter filterip garbage heap many nicotine pattern pile repetition seamless stub...
Air
3d_export
$40
Ucav 3D Model
...ucav 3d model 3dexport unmanned air vehicle ucav uav combat drones drone fighter ucav 3d...
3d_export
$99
Car Chevrolet bel air 3D Model
...chevrolet bel air 3d model
3dexport
car vehicle 3d model cinema 4d image
car chevrolet bel air 3d model gdinesh89 48347 3dexport
3d_export
$28
US Tartar SAM missile 3D Model
...us navy usn usa tartar interceptor sam military surface air rim 24 rocket 3ds cob dxf directx obj short...
3d_export
$45
Russian AS 17 ALCM Krypton Missile 3D Model
...russia ussr china chinese as-17 krypton yj-91 kh-31 alcm air launched cruise anit ship radar radiation russian as 17...
3d_export
$20
Killer Whale 3D Model
...sea false killer whale saltwater fish water aquatic mammal mid-air splashing killer whale 3d model nolgraphic 69815...
3d_export
$95
Falcon3D A340 600 Philippines Air 3D Model
...t civil civilian jetliner a340 a-340 a-340-600 a340-600 airbus
falcon3d a340 600 philippines air 3d model falcon3d 69823 3dexport
3d_export
$95
Falcon3D A340 600 Swiss Air 3D Model
...win jet civil civilian jetliner a340 a-340 a-340-600 a340-600 airbus
falcon3d a340 600 swiss air 3d model falcon3d 69964 3dexport
3d_export
$119
Chevrolet Bel Air Convertible 1955 3D Model
...brio roadster 50s oldtimer antique vintage classic retro car usa
chevrolet bel air convertible 1955 3d model squir 50012 3dexport
3d_export
$50
Mitsushito air conditioner 3D Model
...ner 3d model
3dexport
mitsushito air conditioner 3d model max obj 3ds
mitsushito air conditioner 3d model miniyeti 69189 3dexport
3d_ocean
$5
Donut Balloon
...donut balloon 3docean air balloon color deco dessert donut float floating friend globe...