Thingiverse
piip66 by Nemiah
by Thingiverse
Last crawled date: 3 years ago
Parts for fitting a Raspberry Pi 3 with Adafruit LCD in a water protected IP66 enclosure.
The left side of the inner enclosure can be lifted off by squeezing your fingers after putting them in the top and bottom holes. The part holds in place without screws.
The right side is mounted with three screws on the scaffolding.
All Raspberry Pi ports are accessible. You'll need an angled connector for the power though. It is quite tight in there.
An extra handle keeps the Pi in place.
The airflow is optimized to utilize as much of the enclosure as possible. The Pi core temperature was stable in several tests.
The cable gland allows for a small network plug to go through. It might need some filling afterwards though.
For commercial use please contact me.
No post processing necessary, prints perfectly from bottom to top.
Cable gland: M20
Power: micro USB with right angle connector
Screws: 2 x 10mm, 10 pieces
Enclusure: FIBOX MNX PCM 150/100 T
LCD: Adafruit PiTFT - 320x240 2.8" TFT
The left side of the inner enclosure can be lifted off by squeezing your fingers after putting them in the top and bottom holes. The part holds in place without screws.
The right side is mounted with three screws on the scaffolding.
All Raspberry Pi ports are accessible. You'll need an angled connector for the power though. It is quite tight in there.
An extra handle keeps the Pi in place.
The airflow is optimized to utilize as much of the enclosure as possible. The Pi core temperature was stable in several tests.
The cable gland allows for a small network plug to go through. It might need some filling afterwards though.
For commercial use please contact me.
No post processing necessary, prints perfectly from bottom to top.
Cable gland: M20
Power: micro USB with right angle connector
Screws: 2 x 10mm, 10 pieces
Enclusure: FIBOX MNX PCM 150/100 T
LCD: Adafruit PiTFT - 320x240 2.8" TFT
Similar models
thingiverse
free
Revised Raspberry Pi + Adafruit LCD Case by anoved
... at left of buttons. (top half)
the camsocket alternate top includes a hole i can use to mount my raspberry pi's camera in.
thingiverse
free
Raspberry Pi Picoprobe enclosure by TheFlyingKipper
...f open for easy access to the bootsel button for program updates.
top and bottom panels can be left off for an open frame design.
thingiverse
free
Raspberry Pi with Adafruit LCD Pi Plate Enclosure by builttospec
...embly instructions with pics here:http://www.built-to-spec.com/blog/raspberry-pi-and-adafruit-lcd-enclosure
design by robolemur
thingiverse
free
Raspberry Pi Display 8 terminal cover by petrex
...rry pi enclosure, includes housing for eight screw terminals and side holes for adafruit lcd display without snapping pcb mounts.
cg_trader
free
Adafruit raspberry Pi case
...39;t add the hole for the pi case enclosure acrylic pi raspberry engineering construction raspberry pi architectural raspberry pi
cults
free
Adafruit 2.2" PiTFT Raspberry Pi A+ Enclosure
...y pi a+ enclosure
cults
adafruit 2.2" pitft raspberry pi a+ enclosure
adafruit 2.2" pitft raspberry pi a+ enclosure
grabcad
free
Table top clock using Raspberry pi zero
...p. and the bottom part consists of mount for rpi zero and provision for mini hdmi & usb ports and a vent for the thermals .
thingiverse
free
Raspberry Pi B/B+/3 Enclosure by JustAHobby_Maker
...mixed off the adafruit version. this one has taller sides so as to make for a good enclosure for the pi + adafruit pitft display.
thingiverse
free
Raspberry Pi portable case by n602
...berry pi, adafruit's pitft, gpio cable, m2.6(2.5) bolt(8mm long) & nut and mobile battery (& cable) 're required.
thingiverse
free
WIP Raspberry Pi enclosure by morphygee
... is transparent filament and should light up while raspi is on
have to drill a hole for power connector and maybe for ir-receiver