Thingiverse
PiCade-HAT Based 10" HD Mini Bartop (Re-design) by Zurkeyon
by Thingiverse
Last crawled date: 3 years ago
https://www.youtube.com/watch?v=hTGTHzLN20g
*Now Battery Powered! 5+ Hour Battery life!
Use Boost converter:https://www.amazon.com/Yeeco-Converter-Regulator-Stabilizer-Adjustable/dp/B011EBSKK0/ref=sr_1_3?s=wireless&ie=UTF8&qid=1526397789&sr=1-3&keywords=5+to+12V+boost+converter&dpID=51xw5k2jkoL&preST=_SX300_QL70_&dpSrc=srch
Amazon - $7.76
And a RAVPOWER RP-PB41 Battery:https://www.amazon.com/Portable-Charger-RAVPower-Battery-26800mAh/dp/B012NIQG5E/ref=sr_1_1?ie=UTF8&qid=1526397747&sr=8-1&keywords=RP-PB41
More Battery Info:https://www.youtube.com/watch?v=aVNQKss2Bwk
Re-Designed 6- Button Layout!
This is a ground-up Remix of malopezn's Arcade Cabinet.
Found Here: http://www.thingiverse.com/thing:768663
Big Thanks to malopezn for the initial Design, as it saved me a TON of time.
For this build I decided to use a Raspberry Pi3, High Def 10" Screen, 6 button Layout, NeoPixel lighting, an Arduino Nano, and a Pimoroni Picade parts kit.
This still prints on any 200x200x160+ Prusa or better, and for the most part does not need any support. The Light Frames do need support for the parts touching the Bed plate.
So Far I have added the Following to the design:
Refit Location for the Raspberry PI 2/3 (Removed B Model Mounting)
Added Mounting for the HDMI Screen Controller Board
Added Mounting Area for the HDMI Screen Control Board and IR LED
New ATX Molex Power Supply Cut Out
Added a Cut out to Wire LED Strip into the Cabinet Marquis
Inserts for the Cabinet Marquis (White or Clear, Painted Letters, Accented by LED Strips)
Added Glue-On Printable Decals (Pac-Style)http://www.thingiverse.com/thing:681851
Refitted to use a Pimoroni Picade KIT (Exact Fit)
Speaker mounting added (For Picade Kit Speaker - Exact Fit)
Slotted mounting where possible to make fitment more flexible
Holes added to Left Upright, to allow LCD driver board screws to be reached easily.
10" Screen frame added. allows you to make the 10" LCD into a more hearty assembly.
Switched to Magnetic Mounting for screen, for easy service and card swaps.
Possible Upgrades Still to Be Implemented:
Nanopixel Illuminated Buttons
Sound Reactive Buttons and Marquee
On/Off switch for Marquee
Portable Lithium Battery Power and Charging (Implemented, See Above!)
Coin Slot
Trackball or Ergo Trackpad
Water or Peltier Cooling for Overclocking the PI.
Illuminated Side Panel Decals
And So much room for more in this little guy :-)
Customize to your hearts desire, All Design Files Included!
Build Parts List:
x2 Rolls of PLA or ABS Plastic, Plus a little bit of CLEAR for the Marquee.
EDIT: Some items are missing now in Amazon, I will Re-link what I can. I have not bought and verified each of these, its just what I could find at the request of someone in the comments. Please do your homework on reviews and make sure you are buying from good sellers.
10" HDMI Screen 1280 x 800 (Non-Touch) 100$https://www.amazon.com/10-1-inch-Diagonal-Especially-Raspberry/dp/B01JJ60LZE
Molex 5 AMP Power Supply - $20.00 + Shipping (Comes with a SATA to USB Kit)https://www.amazon.com/110v-Power-Supply-Molex-5000mA/dp/B002TJNDU4/ref=sr_1_4?s=electronics&ie=UTF8&qid=1526395875&sr=1-4&keywords=molex+Power+Supply&dpID=51sSk3Xx17L&preST=_SX300_QL70_&dpSrc=srch
MUST be 2.5a/2.5a (5 Total Amps) or it will NOT be powerful enough to run the PI AND the screen! These are hard to source. One of the above unit should do the trick!
Neopixel Type Lights (Any WS2812 Addressable LED works)- ($16.00 - 20$)https://www.amazon.com/Addressable-Sealed-WS2812-30-LED-Strip/dp/B01GYDLJ24/ref=sr_1_10?s=electronics&ie=UTF8&qid=1526396135&sr=1-10&keywords=WS2812+LEd
ORhttps://www.amazon.com/TOOGOO-WS2812-8-5050-Driver-Development/dp/B0757C6X5C/ref=sr_1_13?s=electronics&ie=UTF8&qid=1526396135&sr=1-13&keywords=WS2812+LEd
An Arduino Nano v3 Type, or Clone, to Control them with: (3$ - 10$)
All Over the Webhttps://www.amazon.com/s/ref=nb_sb_noss_2?url=search-alias%3Delectronics&field-keywords=Arduino+Nano&rh=n%3A172282%2Ck%3AArduino+Nano
Raspberry PI3 ($35.00)
All over the Web
64gb Class10 Micro SD Card (20-25$)https://www.amazon.com/s/ref=nb_sb_noss_2?url=search-alias%3Delectronics&field-keywords=Micro+SD+64GB+Class+10&rh=n%3A172282%2Ck%3AMicro+SD+64GB+Class+10
Pimironi Picade HAT Kit - $54.00 Shipped.https://shop.pimoroni.com/products/picade-hat
Short HDMI Cable - $10 Average (I had one laying around)
Hardware Fasteners! Mix of 1/4" Nuts and Bolts should get you done. (Approx $15)
I used x2 hobby bolt packs from the hardware store.
Uses x4 Neodymium Magnets to hold the halves together. (Approx $10.00)
Magnets are 6.35mm x.6.35mm x 25.42mm N42 Strength. (37 lbs of Pull Force)
1/4" x 1/4" x 1"https://www.kjmagnetics.com/proddetail.asp?prod=B44X0
Glue. I use Loctite go2 Glue. As it Dries Perfectly Clear and is relatively strong. $5.00http://www.midlandhardware.com/164309.html?gclid=Cj0KEQiAw_DEBRChnYiQ_562gsEBEiQA4LcsssCUvJgLsK9W-IvjbX9tngGxEL68p-Ndi5wT9aKHTpMaAjlc8P8HAQ
Also helpful to have:
https://www.amazon.com/s/ref=nb_sb_noss?url=search-alias%3Delectronics&field-keywords=Prototype+Green+Board&rh=n%3A172282%2Ck%3APrototype+Green+Board
Circuit Project Plates
Andhttps://www.amazon.com/s/ref=nb_sb_noss?url=search-alias%3Daps&field-keywords=Jumper+Wire+bread+board&rh=i%3Aaps%2Ck%3AJumper+Wire+bread+board
Jumper Sets...
As they make the build WAY easier!
Approximate Kit Build Cost = $250-350 If you shop around, you can do even better...
This is a LONG build, and printing time is measured in days to weeks, depending on your machine... But its Worth it :-)
Basic Build Steps:
Print out all parts. Including x4 Magnet Blocks, and the Marquee in CLEAR or White.
Wire Up the Kit and Test all Parts, Using the guides Below to get your image working and controls set up.
Start Cleaning up wire. Zip Ties and Twisting are what worked best for me.
Start bonding all parts together.
Mount all boards.
Mount Screen into Frame.(After Cleaning the Supports VERY Well.
(File the inside of the frame down if needed, if it presses in on the edges too hard it creates white distortions at the edge of the screen that will eventually cause damage)
Glue in Magnet Blocks and Neodymium Magnets, Clamping them to Set 100% before any test fitting of the top and Bottom. Or it WILL pull the blocks out...
Wire up the Arduino and Neopixel Lights. Wire their power up to the aaccessory 5v on the top of the picade, and the grounds to the right of that, also on the picade hat accessory area. (5-6 holes that are labeled for use on the face of the board itself)
Program the Neopixels and test them.
Do a full power up and down test once fully assembled. Check components for heat.
Close up the unit and make sure ALL controls work by re-setting up the emulationstation controls.
Set up a Mouse or Trackball for Missile command and the like...
(Guides on the Web for this)
Then its.... GAME ON!
Light Controller How To:
https://create.arduino.cc/projecthub/whimsy-makerspace/arduino-compatible-nano-neopixel-controller-6f0c4b
How to Wire Up The PiCade HAT:
https://learn.pimoroni.com/tutorial/sandyj/getting-started-with-picade-hat
Detailed Adding Roms and DIY Attract Mode Setup and Config.
--->https://www.youtube.com/watch?v=eYCPFO4lclA<---
Deans Attract Mode ShortCut Setup...
--->https://www.youtube.com/watch?v=WtRsMrUWgu4&t=582s<---
Retropie Dean's Attract mode, Plus Picade HAT setup.http://retromaniacus.com/gaming-front-ends/retropie/deans-gamestation-32gb/
MUST Signup through Facebook, All other signups are AUTO REJECTED!
Download Dean's Attract mode Image.
Flash to a 32GB+GB card using win32DiskImager
Edit the Config.txt file onthe boot partition before removing the key.
Change:
--> #framebuffer_width=1280
--> #framebuffer_height=720
to
framebuffer_width=1280
framebuffer_height=800
And Change:
dtparam=audio=on
to
--> #dtparam=audio=on
Then Save the File and remove the key.
Insert it into your PI3 and boot up.
Exit Attract mode with a keyboard using the escape key, as your buttons will not work yet.
At the Command Prompt type the following:
sudo dpkg-reconfigure keyboard-configuration
Setup a 101, English US, Defaults on the altgr and no compose key... (Make sure it all Says US and hit enter after that till its done and back at the command bar at the bottom. Basically)
Type: sudo reboot
Hit enter and wait for reboot
Exit Attract mode. (May have to force exit with CTRL-C at this point.)
(Plug in an Ethernet cable to the PI and to some internet for the next part)
At a command line type the following:
curl -sS https://get.pimoroni.com/picadehat | bash
Saying yes to the first option, so it runs (takes a little bit to run), and yes to the use speaker on the picade hat option.
You can say yes or no to the rom option. It has no bearing on sound or function.
Type: sudo reboot
Hit enter and wait for reboot.
You should hear sound.
Buttons and keys need to be setup.
ISSUE: MAME coin (Acting as keyboard Button "C" and is on the Front Left of the unit) is not working correctly in lr-mame2010 (Which is what Dean's Image uses)
Easy SOLUTION: Make changes to the picade hat default button profile to map C and S to NUM5 and NUM1
At a command line, type the following:
cd Pimoroni/picade/picade-hat/gamepads/
cp picadehat-default picadehat-backup
sudo vi picadehat-default
edit the following....
Under "Keys :{"
Change COIN to 5
and START to 1
:wq and exit
./configload picadehat-default
Say yes to Reboot.
Now go into Emulationstation, Retropie, and Retroarch.
Reset the Keys in the order of... Retroarch First, then Emulationstation, then Attract mode and Emulators.
If you go in that order you will have a less difficult time of it.
But no matter how you slice it, setting up Picade Buttons Sucks
_____
Master Tip: When setting up buttons and testing key configurations, the command line in retropie, allows you to simply type "showkey" and it will briefly start showing you the results of joystick moves and button presses.
It stops on its own after about a minute. Re-Run it as many times as you like to make sure all your connections are working.
_____
*Now Battery Powered! 5+ Hour Battery life!
Use Boost converter:https://www.amazon.com/Yeeco-Converter-Regulator-Stabilizer-Adjustable/dp/B011EBSKK0/ref=sr_1_3?s=wireless&ie=UTF8&qid=1526397789&sr=1-3&keywords=5+to+12V+boost+converter&dpID=51xw5k2jkoL&preST=_SX300_QL70_&dpSrc=srch
Amazon - $7.76
And a RAVPOWER RP-PB41 Battery:https://www.amazon.com/Portable-Charger-RAVPower-Battery-26800mAh/dp/B012NIQG5E/ref=sr_1_1?ie=UTF8&qid=1526397747&sr=8-1&keywords=RP-PB41
More Battery Info:https://www.youtube.com/watch?v=aVNQKss2Bwk
Re-Designed 6- Button Layout!
This is a ground-up Remix of malopezn's Arcade Cabinet.
Found Here: http://www.thingiverse.com/thing:768663
Big Thanks to malopezn for the initial Design, as it saved me a TON of time.
For this build I decided to use a Raspberry Pi3, High Def 10" Screen, 6 button Layout, NeoPixel lighting, an Arduino Nano, and a Pimoroni Picade parts kit.
This still prints on any 200x200x160+ Prusa or better, and for the most part does not need any support. The Light Frames do need support for the parts touching the Bed plate.
So Far I have added the Following to the design:
Refit Location for the Raspberry PI 2/3 (Removed B Model Mounting)
Added Mounting for the HDMI Screen Controller Board
Added Mounting Area for the HDMI Screen Control Board and IR LED
New ATX Molex Power Supply Cut Out
Added a Cut out to Wire LED Strip into the Cabinet Marquis
Inserts for the Cabinet Marquis (White or Clear, Painted Letters, Accented by LED Strips)
Added Glue-On Printable Decals (Pac-Style)http://www.thingiverse.com/thing:681851
Refitted to use a Pimoroni Picade KIT (Exact Fit)
Speaker mounting added (For Picade Kit Speaker - Exact Fit)
Slotted mounting where possible to make fitment more flexible
Holes added to Left Upright, to allow LCD driver board screws to be reached easily.
10" Screen frame added. allows you to make the 10" LCD into a more hearty assembly.
Switched to Magnetic Mounting for screen, for easy service and card swaps.
Possible Upgrades Still to Be Implemented:
Nanopixel Illuminated Buttons
Sound Reactive Buttons and Marquee
On/Off switch for Marquee
Portable Lithium Battery Power and Charging (Implemented, See Above!)
Coin Slot
Trackball or Ergo Trackpad
Water or Peltier Cooling for Overclocking the PI.
Illuminated Side Panel Decals
And So much room for more in this little guy :-)
Customize to your hearts desire, All Design Files Included!
Build Parts List:
x2 Rolls of PLA or ABS Plastic, Plus a little bit of CLEAR for the Marquee.
EDIT: Some items are missing now in Amazon, I will Re-link what I can. I have not bought and verified each of these, its just what I could find at the request of someone in the comments. Please do your homework on reviews and make sure you are buying from good sellers.
10" HDMI Screen 1280 x 800 (Non-Touch) 100$https://www.amazon.com/10-1-inch-Diagonal-Especially-Raspberry/dp/B01JJ60LZE
Molex 5 AMP Power Supply - $20.00 + Shipping (Comes with a SATA to USB Kit)https://www.amazon.com/110v-Power-Supply-Molex-5000mA/dp/B002TJNDU4/ref=sr_1_4?s=electronics&ie=UTF8&qid=1526395875&sr=1-4&keywords=molex+Power+Supply&dpID=51sSk3Xx17L&preST=_SX300_QL70_&dpSrc=srch
MUST be 2.5a/2.5a (5 Total Amps) or it will NOT be powerful enough to run the PI AND the screen! These are hard to source. One of the above unit should do the trick!
Neopixel Type Lights (Any WS2812 Addressable LED works)- ($16.00 - 20$)https://www.amazon.com/Addressable-Sealed-WS2812-30-LED-Strip/dp/B01GYDLJ24/ref=sr_1_10?s=electronics&ie=UTF8&qid=1526396135&sr=1-10&keywords=WS2812+LEd
ORhttps://www.amazon.com/TOOGOO-WS2812-8-5050-Driver-Development/dp/B0757C6X5C/ref=sr_1_13?s=electronics&ie=UTF8&qid=1526396135&sr=1-13&keywords=WS2812+LEd
An Arduino Nano v3 Type, or Clone, to Control them with: (3$ - 10$)
All Over the Webhttps://www.amazon.com/s/ref=nb_sb_noss_2?url=search-alias%3Delectronics&field-keywords=Arduino+Nano&rh=n%3A172282%2Ck%3AArduino+Nano
Raspberry PI3 ($35.00)
All over the Web
64gb Class10 Micro SD Card (20-25$)https://www.amazon.com/s/ref=nb_sb_noss_2?url=search-alias%3Delectronics&field-keywords=Micro+SD+64GB+Class+10&rh=n%3A172282%2Ck%3AMicro+SD+64GB+Class+10
Pimironi Picade HAT Kit - $54.00 Shipped.https://shop.pimoroni.com/products/picade-hat
Short HDMI Cable - $10 Average (I had one laying around)
Hardware Fasteners! Mix of 1/4" Nuts and Bolts should get you done. (Approx $15)
I used x2 hobby bolt packs from the hardware store.
Uses x4 Neodymium Magnets to hold the halves together. (Approx $10.00)
Magnets are 6.35mm x.6.35mm x 25.42mm N42 Strength. (37 lbs of Pull Force)
1/4" x 1/4" x 1"https://www.kjmagnetics.com/proddetail.asp?prod=B44X0
Glue. I use Loctite go2 Glue. As it Dries Perfectly Clear and is relatively strong. $5.00http://www.midlandhardware.com/164309.html?gclid=Cj0KEQiAw_DEBRChnYiQ_562gsEBEiQA4LcsssCUvJgLsK9W-IvjbX9tngGxEL68p-Ndi5wT9aKHTpMaAjlc8P8HAQ
Also helpful to have:
https://www.amazon.com/s/ref=nb_sb_noss?url=search-alias%3Delectronics&field-keywords=Prototype+Green+Board&rh=n%3A172282%2Ck%3APrototype+Green+Board
Circuit Project Plates
Andhttps://www.amazon.com/s/ref=nb_sb_noss?url=search-alias%3Daps&field-keywords=Jumper+Wire+bread+board&rh=i%3Aaps%2Ck%3AJumper+Wire+bread+board
Jumper Sets...
As they make the build WAY easier!
Approximate Kit Build Cost = $250-350 If you shop around, you can do even better...
This is a LONG build, and printing time is measured in days to weeks, depending on your machine... But its Worth it :-)
Basic Build Steps:
Print out all parts. Including x4 Magnet Blocks, and the Marquee in CLEAR or White.
Wire Up the Kit and Test all Parts, Using the guides Below to get your image working and controls set up.
Start Cleaning up wire. Zip Ties and Twisting are what worked best for me.
Start bonding all parts together.
Mount all boards.
Mount Screen into Frame.(After Cleaning the Supports VERY Well.
(File the inside of the frame down if needed, if it presses in on the edges too hard it creates white distortions at the edge of the screen that will eventually cause damage)
Glue in Magnet Blocks and Neodymium Magnets, Clamping them to Set 100% before any test fitting of the top and Bottom. Or it WILL pull the blocks out...
Wire up the Arduino and Neopixel Lights. Wire their power up to the aaccessory 5v on the top of the picade, and the grounds to the right of that, also on the picade hat accessory area. (5-6 holes that are labeled for use on the face of the board itself)
Program the Neopixels and test them.
Do a full power up and down test once fully assembled. Check components for heat.
Close up the unit and make sure ALL controls work by re-setting up the emulationstation controls.
Set up a Mouse or Trackball for Missile command and the like...
(Guides on the Web for this)
Then its.... GAME ON!
Light Controller How To:
https://create.arduino.cc/projecthub/whimsy-makerspace/arduino-compatible-nano-neopixel-controller-6f0c4b
How to Wire Up The PiCade HAT:
https://learn.pimoroni.com/tutorial/sandyj/getting-started-with-picade-hat
Detailed Adding Roms and DIY Attract Mode Setup and Config.
--->https://www.youtube.com/watch?v=eYCPFO4lclA<---
Deans Attract Mode ShortCut Setup...
--->https://www.youtube.com/watch?v=WtRsMrUWgu4&t=582s<---
Retropie Dean's Attract mode, Plus Picade HAT setup.http://retromaniacus.com/gaming-front-ends/retropie/deans-gamestation-32gb/
MUST Signup through Facebook, All other signups are AUTO REJECTED!
Download Dean's Attract mode Image.
Flash to a 32GB+GB card using win32DiskImager
Edit the Config.txt file onthe boot partition before removing the key.
Change:
--> #framebuffer_width=1280
--> #framebuffer_height=720
to
framebuffer_width=1280
framebuffer_height=800
And Change:
dtparam=audio=on
to
--> #dtparam=audio=on
Then Save the File and remove the key.
Insert it into your PI3 and boot up.
Exit Attract mode with a keyboard using the escape key, as your buttons will not work yet.
At the Command Prompt type the following:
sudo dpkg-reconfigure keyboard-configuration
Setup a 101, English US, Defaults on the altgr and no compose key... (Make sure it all Says US and hit enter after that till its done and back at the command bar at the bottom. Basically)
Type: sudo reboot
Hit enter and wait for reboot
Exit Attract mode. (May have to force exit with CTRL-C at this point.)
(Plug in an Ethernet cable to the PI and to some internet for the next part)
At a command line type the following:
curl -sS https://get.pimoroni.com/picadehat | bash
Saying yes to the first option, so it runs (takes a little bit to run), and yes to the use speaker on the picade hat option.
You can say yes or no to the rom option. It has no bearing on sound or function.
Type: sudo reboot
Hit enter and wait for reboot.
You should hear sound.
Buttons and keys need to be setup.
ISSUE: MAME coin (Acting as keyboard Button "C" and is on the Front Left of the unit) is not working correctly in lr-mame2010 (Which is what Dean's Image uses)
Easy SOLUTION: Make changes to the picade hat default button profile to map C and S to NUM5 and NUM1
At a command line, type the following:
cd Pimoroni/picade/picade-hat/gamepads/
cp picadehat-default picadehat-backup
sudo vi picadehat-default
edit the following....
Under "Keys :{"
Change COIN to 5
and START to 1
:wq and exit
./configload picadehat-default
Say yes to Reboot.
Now go into Emulationstation, Retropie, and Retroarch.
Reset the Keys in the order of... Retroarch First, then Emulationstation, then Attract mode and Emulators.
If you go in that order you will have a less difficult time of it.
But no matter how you slice it, setting up Picade Buttons Sucks
_____
Master Tip: When setting up buttons and testing key configurations, the command line in retropie, allows you to simply type "showkey" and it will briefly start showing you the results of joystick moves and button presses.
It stops on its own after about a minute. Re-Run it as many times as you like to make sure all your connections are working.
_____
Similar models
thingiverse
free
Infinity Mirror by mikeybme
...ow+film&qid=1620461637&sr=8-15
filament - https://www.amazon.com/dp/b00zauqzta?psc=1&ref=ppx_yo2_dt_b_product_details
thingiverse
free
3D Printable 3D Printer by TheJadeRabbit
...r_1_4?ie=utf8&qid=1530916900&sr=8-4&keywords=3d+printer+hotend
code(marlin): https://github.com/marlinfirmware/marlin
thingiverse
free
Light Up Emergency Power Button/Switch by Coopster
...s anywhere in series with your circuit and be sure to test continuity before you clip if closed.
that's it, you're done!
thingiverse
free
Illuminated Football-Stand by froetz
...swq/ref=sr_1_10?__mk_de_de=%c3%85m%c3%85%c5%bd%c3%95%c3%91&dchild=1&keywords=wemos+mini+d1&qid=1614665976&sr=8-10
thingiverse
free
Speaker box by Ratakis
...-4ft/dp/b01kstsv76/ref=sr_1_1_sspa?s=electronics&ie=utf8&qid=1521518432&sr=1-1-spons&keywords=aux+cable&psc=1
thingiverse
free
Torvol tool organizer by Collinhasasthma
...ver-electronic-short-circuit-available/dp/b088tvvnvm/ref=sr_1_4?dchild=1&keywords=smoke+stopper&qid=1623510410&sr=8-4
thingiverse
free
Electric Screwdriver Dock by stevesch
...for a common model i purchased from amazon. it's similar to some of the "wowstick" models in form factor....
thingiverse
free
The Cube Mini Fridge by thewatchmakerfl
...ref=sr_1_2?ie=utf8&qid=1436833279&sr=8-2&keywords=potentiometer&pebp=1436833322445&perid=0pmtmyyyy6vn4mzst3fx
thingiverse
free
Kingroon KP3S Klipper 0.96 oled screen by nehiLo
...//
printer.cfg
[mcu host]
serial: /tmp/klipper_host_mcu
[display]
lcd_type: ssd1306
menu_timeout: 30
i2c_mcu: host
i2c_bus: i2c.1
thingiverse
free
noyce64 by noycebru
...e silicone wire electric wire 28 gauge coper hook up ... https://www.amazon.com/dp/b01kq2lhfi/ref=cm_sw_r_tw_dp_u_x_vlwzeb4zsjbkt
Zurkeyon
thingiverse
free
Magnetic Container Rack by Zurkeyon
...gth.
1/4" x 1/4" x 1"https://www.kjmagnetics.com/proddetail.asp?prod=b44x0
can hold about 4-5 lbs. (approx)
enjoy!
thingiverse
free
Graphics Card Brace by Zurkeyon
...odify to your liking.
i have included the sketchup files for tweaking and adjustments.
make whatever use of it you can.
enjoy!
thingiverse
free
PC504XS Camera Mount (Supercircuits) by Zurkeyon
...4.6 as the enclosure walls are very thin.
but i'm sure someone will be a bit more perfectionist and correct this :-)
enjoy!
thingiverse
free
140MM Dia Blower Fan Wheel by Zurkeyon
... the apparatus to perform the balancing.
http://whiteglovefans.com/blog/2013/9/22/static-balancing-blades
balancing info (manual)
thingiverse
free
Odroid-VU7 and VU7+ Screen Frame by Zurkeyon
...ught i would include.
enjoy!
(current version should hide the screen edges better than in the pics, if not its easy to modify.)
thingiverse
free
Laptop HDD Hot Swap Cage by Zurkeyon
...of screw holes on the end of the drive for mounting a handle to.
glue them together for unlimited sata storage upgrades!
enjoy!
thingiverse
free
SoC ExoSkeleton DevTop by Zurkeyon
...most a necessity. with enough flexibility to make it truly useful!
a place for everything, everything in its place!
:-p
enjoy!
z
thingiverse
free
NanoDrives Time Machine by Zurkeyon
...g your customers 3000$! :-d
enjoy!
-z-
full instructable available also.http://www.instructables.com/id/nanodrives-time-machine
thingiverse
free
PiCade Light Frames - RetroPi - Pac Man by ChrisMayhew
...some alternative light frames for the picade designed by zurkeyon retropi text with pacman logo. for the transparent part,...
thingiverse
free
SoC ExoSkeleton DevTop 2.0 by Zurkeyon
...ost a necessity. with enough flexibility to make it truly useful!
a place for everything, everything in its place!
:-p
enjoy!
-z-
Picade
thingiverse
free
Picade by jaimecuevas290
...picade by jaimecuevas290
thingiverse
this a 3d print for rassberry pi
thingiverse
free
picade 1 by jaimecuevas290
...picade 1 by jaimecuevas290
thingiverse
for rasberry pi
thingiverse
free
picade 2 by jaimecuevas290
...picade 2 by jaimecuevas290
thingiverse
for rasabbery pi
thingiverse
free
picade 3 by jaimecuevas290
...picade 3 by jaimecuevas290
thingiverse
for raspberry pi
thingiverse
free
picade 4 by jaimecuevas290
...picade 4 by jaimecuevas290
thingiverse
for raspberry pi
thingiverse
free
Picade Backplate
...ll designed, but because i don't like a few methods they used.
read more here: http://wiki.port23.de/wiki/picade_improvements
thingiverse
free
Improved Picade bracket by Authenticaco
...xagonal holes for holding the nuts in place when fastening the parts together. use a machine screw to pull the nuts in the holes.
thingiverse
free
PiCade Light Frames - RetroPi - Pac Man by ChrisMayhew
...yon. retropi text with pacman logo.
for the transparent part, i used clear petg and did a filament swap for the text back to pla.
thingiverse
free
RCade - Laser cut files for RC2014 modifications to Pimoroni Picade by semachthemonkey
... of the rc2014 see https://rc2014.co.uk/
the picade cabinet can be bought from pimoroni https://shop.pimoroni.com/products/picade
thingiverse
free
Remix for PiCade-KickerPanel by mrpottermw
... mix it up a little.
i used the bracket from http://www.thingiverse.com/thing:922740 and fused it with the existing kicker panel.
Bartop
thingiverse
free
Bartop Arcade by mattsplat
...bartop arcade by mattsplat
thingiverse
mini bartop arcade made of mdf using raspberry pi.
thingiverse
free
BARTOP 2 players by wayzoken
...bartop 2 players by wayzoken
thingiverse
bartop 2 players
thingiverse
free
Bartop Arcades by Marksworld
...bartop arcades by marksworld
thingiverse
2 arcade bartop machines. basic shape designed ready for you do build or edit.
thingiverse
free
Shinobi handle and speaker enclosure for bartop by ian57
...shinobi handle and speaker enclosure for bartop by ian57
thingiverse
made these models for my bartop shinobi
thingiverse
free
Bartop Arcade toggle switch slot by eternityoffate
...e switch slot by eternityoffate
thingiverse
this is to fit a switch button the slot of a gameroomsolutions bartop arcade cabinet
thingiverse
free
Piedino Bartop by MiguelBi
...ltrini da 20mm di diametro. h20mm.
base 43mm, perfetti per feltrini da 24mm di diametro. h20mm.
usare viti m5 in entrambi i casi.
thingiverse
free
Arcade BarTop by LisBonMeKat
...
videohttps://youtu.be/ruxvy5cawcw
added a v2.2 dxf file with 6 buttons and pinball, also readdy for a 120mm fan.. good games..
thingiverse
free
Arcade Bartop Monitor Backplate Adjustable Mount by dpagett
...or in your bartop or arcade machine if you need to adjust the angle of the display to sit flush or parallel with the bezel glass.
thingiverse
free
Bartop Power Grid by MiguelBi
...p mediante bulloni t.bombati quadri m5x30. (vedere foto in allegato).
dimensioni riquadro da ritagliare sulla mensola: 110mmx40mm
thingiverse
free
Bartop arcade makers mini vewlix by VELTA-3D
...y velta-3d
thingiverse
je partage mon bartop réaliser il y a maintenant 2 ans.
https://www.facebook.com/groups/1484894498495619/
Hd
thingiverse
free
HD CASE
...hd case
thingiverse
3.5in hd case
(also see thing:3892498 & thing:3721003)
thingiverse
free
Laser HD TPU
...laser hd tpu
thingiverse
transtec laser hd tpu
thingiverse
free
hd by apalmisano098
...hd by apalmisano098
thingiverse
n
thingiverse
free
Support HD by Pifle
...support hd by pifle
thingiverse
3 symmetrical elements to support your hd
thingiverse
free
HD Caddy 3.5in HD 3X by STEGOBOARD
...drives.
requires:
twelve 6-32 x 3/8" long machine screws.
for ideas on how to use this 3d printed item, visit:stegoboard.com
thingiverse
free
HD Caddy 3.5in HD 2X by STEGOBOARD
... drives.
requires:
eight 6-32 x 3/8" long machine screws.
for ideas on how to use this 3d printed item, visit:stegoboard.com
thingiverse
free
HD Caddy 2.5in HD 3X by STEGOBOARD
...d state drives.
requires:
twelve m3 x 8mm long machine screws.
for ideas on how to use this 3d printed item, visit:stegoboard.com
thingiverse
free
HD Caddy 2.5in HD 2X by STEGOBOARD
...id state drives.
requires:
eight m3 x 8mm long machine screws.
for ideas on how to use this 3d printed item, visit:stegoboard.com
thingiverse
free
HD logo by bandit-ed
...hd logo by bandit-ed
thingiverse
hd logo
thingiverse
free
Five33 Switchback HD by FlyFive33
...five33 switchback hd by flyfive33
thingiverse
switchback hd prints
Hat
thingiverse
free
Hat
...hat
thingiverse
this is a hat
thingiverse
free
Cat In The Hat hat by ChristenKratz
...cat in the hat hat by christenkratz
thingiverse
cat in the hat
thingiverse
free
HAT POLE
...hat pole
thingiverse
hat pole
put hat on pole
thingiverse
free
Witch Hat (or Wizard Hat) by nicholasclewis
... (or wizard hat) by nicholasclewis
thingiverse
here is a cool witch hat (or printed in uv happy pla it looks like a wizard hat).
thingiverse
free
HAT by yuh1973
...hat by yuh1973
thingiverse
hat
thingiverse
free
HAT by yuh1973
...hat by yuh1973
thingiverse
hat
thingiverse
free
HATS by nagato
...hats by nagato
thingiverse
hats
thingiverse
free
Basic Hat
...basic hat
thingiverse
just a basic top hat
thingiverse
free
Top Hat
...top hat
thingiverse
little top hat boi
thingiverse
free
Hat Hook
...hat hook
thingiverse
a hat hook i designed to hang my hats on my wall so i can display them
Re
thingiverse
free
The RE Brigade - (RE-04 + RE-05 + RE-06) by MaxRaw
...g to work in concert with the re brigade.
do you like our models?
you can support us on patreon! :)https://www.patreon.com/maxraw
thingiverse
free
re by danielfer
...re by danielfer
thingiverse
rth
thingiverse
free
Test Res by Goatee
...test res by goatee
thingiverse
test res
thingiverse
free
sine nomine res
...sine nomine res
thingiverse
sine nomine res
thingiverse
free
Nautilus Re-Mix
...nautilus re-mix
thingiverse
re-mix of nautilus.
thingiverse
free
Re Badge by motorheadv10
...re badge by motorheadv10
thingiverse
re badge coin
www.werebank.com
thingiverse
free
Re-Arm case
...re-arm case
thingiverse
a case for the re-arm controller board.
thingiverse
free
HTC RE (blue) by jeremy2nis
...htc re (blue) by jeremy2nis
thingiverse
an htc re
thingiverse
free
sine nomine res magnus
...sine nomine res magnus
thingiverse
sine nomine res magnus
thingiverse
free
Concrete Re-bar Cage
...concrete re-bar cage
thingiverse
this is a model of re-bar used in concrete to strengthen the material.
Mini
thingiverse
free
mini castle mini mini golf by EdisonM
...mini castle mini mini golf by edisonm
thingiverse
play able with ball and putter in the "mini mini golf" model
thingiverse
free
Mini Clothesline - Mini Tendal
...mini clothesline - mini tendal
thingiverse
mini clothesline
mini tendal
thingiverse
free
mini mini golf by EdisonM
...mini mini golf by edisonm
thingiverse
actually playable mini mini golf course with putter and ball
thingiverse
free
Mini Schleuder / Mini Slingshot by Ju5tMak3
...mini schleuder / mini slingshot by ju5tmak3
thingiverse
mini schleuder / mini slingshot
have fun
thingiverse
free
mini bomba (mini pump) by neemiasmiranda
...mini bomba (mini pump) by neemiasmiranda
thingiverse
mini bomba
thingiverse
free
MINI by shteffs
...mini by shteffs
thingiverse
mini
thingiverse
free
Mini wrist, Mini poignet by Aleoduc74
...mini wrist, mini poignet by aleoduc74
thingiverse
mini poignet pour vitre ou petit meuble.
thingiverse
free
Mini Bat
...mini bat
thingiverse
mini bats.
thingiverse
free
Mini-Windeisen
...mini-windeisen
thingiverse
mini-windeisen
thingiverse
free
Mini cadeira
...mini cadeira
thingiverse
mini cadeira
10
thingiverse
free
the cube 10 x 10 x 10 mm by 3dluca
...the cube 10 x 10 x 10 mm by 3dluca
thingiverse
cube
10 x 10 x 10 mm
printing time < 5 minutes
thingiverse
free
A-10 Warthog
...a-10 warthog
thingiverse
a-10 warthog (the gun)
thingiverse
free
Stand for Voltcraft Devices SL-10, AN-10, LX-10 by Minfredus
...lmessgeraet_v1" has a "sound level meter sl-10"-branding. file "voltcraft_stand" comes without branding.
thingiverse
free
A-10 warthog
...a-10 warthog
thingiverse
a simple version of an a-10 warthog model
thingiverse
free
10 whisles
...10 whisles
thingiverse
10 whisles
if this is your design let me know
thingiverse
free
AT-10 by JARLANG
...at-10 by jarlang
thingiverse
at-10 british at - 1:72
paper project, but cool :)
thingiverse
free
Universal Z-Braces for CR-10 / CR-10S
...universal z-braces for cr-10 / cr-10s
thingiverse
universal z-braces for cr-10 / cr-10s
thingiverse
free
Fachwerkhaus 10 and 10S
...(original ~6x8m)
scale: optimized for 6mm (1:285)
format: stl
fachwerk / timberframe, optional base, 2 floors, roof with shingles
thingiverse
free
Cr-10s/10 first layer calibration by dilopsus
...cr-10s/10 first layer calibration by dilopsus
thingiverse
first layer calibration test for cr-10s/10 .
rotate model 90 degrees .
thingiverse
free
Creality CR 10 / 10s filament cleaner
...creality cr 10 / 10s filament cleaner
thingiverse
insert ptef tube in holes.
Based
thingiverse
free
Base
...base
thingiverse
this base helps wedge the end of the tape measure to the floor
thingiverse
free
Kings of War Bases / Scenic Bases
... 80mm 3.2mm base with lp
kow 250mm 100mm 3.2mm base with lp
kow 250mm 150mm 3.2mm base with lp
kow 300mm 100mm 3.2mm base with lp
thingiverse
free
base by savethemonsters
...base by savethemonsters
thingiverse
base
thingiverse
free
base by jesse53
...base by jesse53
thingiverse
base
thingiverse
free
base by m2kalista
...base by m2kalista
thingiverse
base
thingiverse
free
Base by danielolivier
...base by danielolivier
thingiverse
base
thingiverse
free
base by savethemonsters
...base by savethemonsters
thingiverse
base part
thingiverse
free
Lamp Base
...lamp base
thingiverse
lamp base
thingiverse
free
The lamp base
...the lamp base
thingiverse
the lamp base
thingiverse
free
20x20 Base
...20x20 base
thingiverse
20x20 base
Design
thingiverse
free
2D Design
...2d design
thingiverse
2d design
thingiverse
free
2D DESIGN
...2d design
thingiverse
2d design
thingiverse
free
Lego design
...lego design
thingiverse
lego design
thingiverse
free
Eggbot designs
...eggbot designs
thingiverse
a bunch of eggbot designs
thingiverse
free
Eggbot Designs
...eggbot designs
thingiverse
a bunch of eggbot designs
thingiverse
free
2D Design
...2d design
thingiverse
the 2d design of the laptop stand.
thingiverse
free
2D Design
...2d design
thingiverse
2d design on adobe illustrator
thingiverse
free
2D design
...2d design
thingiverse
please find attached the ud design
thingiverse
free
3D Design
...3d design
thingiverse
the greatest 3d design in my life.
thingiverse
free
2D Design
...2d design
thingiverse
2d design made with adobe illustrator