Thingiverse
PH145 Brushless FPV Quadcopter by patshead
by Thingiverse
Last crawled date: 3 years, 5 months ago
The PH145 quadcopter was inspired by the RS90 and DJ105 brushless quadcopters. The RS90 looked like fun, but the DJ105 wasn't much bigger and produces a lot more thrust. The DJ105 uses 2.5 inch propellers, and I quickly learned that these are rare. 3 inch propellers are available everywhere, and there's a much bigger selection of motors if you build a little bigger than the DJ105.
My 3D Printed Quadcopter - The PH145 Drone at patshead.com
Like the RS90 and DJ105, my PH145 drone frame is printed using Taulman 910 nylon filament. It is sturdy stuff. I crash all the time.
Version 2.0 of the PH145 frame is the third model I have printed and flown. The prop guards on the prototype model were too thin, and I had an OpenSCAD error at each corner that created a weak point. For version 1.0, I increased the thickness of the prop guards by 50% and corrected the OpenSCAD error. I also added some small zip tie slots on the inside edges of the prop guards.
I was hoping I could get away with the zip tie slots, but they ended up being a weak point, and I finally broke the frame when I crashed into a brick wall.
Version 2.0 removes these zip tie slots, and it moves the holes for the nylon standoffs farther away from the props. It also adds zip tie slots to the bottom frame in an attempt to allow for "zip tie landing gear."
The Version 2.0 frame comes in at 58 grams--8 grams lighter than Version 1.0--when printed with 2 top layers, 2 bottom layers, 4 perimeters, and 20% hexagonal infill with a 0.4mm nozzle. This is my lightest frame to date, and I expect it to be the sturdiest!
My all-up-weight is currently 340 grams with an 850mAh 4S LiPo, and FPV camera and transmitter, and using aluminum screws. The PH145 feels fast and agile with this small battery, and it can usually fly for about 6 minutes.
I'm running tri-blade RotorX RX3040T props, EMAX RS1306 4000Kv motors, a Naze32, and some sort of 4-in-1 (supposedly) 4x30A ESC. I have a Crazepony 700TVL camera and transmitter mounted on the drone. Without a battery, the PH145 weighs in at 245 grams.
PH145 FPV at Oak Point Park
I'm still learning how to fly in FPV. I'm not very good at it yet!
Parts List:
28 M3 screws 8mm Steel Screws or 8mm Aluminum Screws
M3 25mm Nylon Standoffs
LittleBee 30Ax4 4-in-1 ESC
Naze32
DYS BX1306 4000Kv motors or EMAX RS1306 4000KV
Male XT60 battery connector
RotorX RX3040T Props
Taulman 910 filament 1lb
I'm also running this FPV camera and transmitter:
Eachine 700TVL FPV Camera and Transmitter
Eachine EV800 FPV Goggles
These are other batteries I've tried so far:
Venom 50C 850 mAh - 5+ minutes
GARTT 1500mAh 4S - 9.5 minutes
CrazePony Graphene 1300mAh 4S - 8+ minutes
Floureon 2200mAh 3S - 9+ minutes
1300mAh 3S - 5 to 6 minutes (not the brand I used)
A 1300mAh 3S feels like a great way to get used to the quadcopter. I was flying on a well worn 1300mAh that used to belong to a friend. The quadcopter started to feel a bit weaker as I approached the 5 minute mark, but it was more than usable at 6 minutes of air time. You can run 3S batteries if you already have them, but I highly recommend the 850mAh 4S. I have 5 of them, and they're excellent!
My 3D Printed Quadcopter - The PH145 Drone at patshead.com
Like the RS90 and DJ105, my PH145 drone frame is printed using Taulman 910 nylon filament. It is sturdy stuff. I crash all the time.
Version 2.0 of the PH145 frame is the third model I have printed and flown. The prop guards on the prototype model were too thin, and I had an OpenSCAD error at each corner that created a weak point. For version 1.0, I increased the thickness of the prop guards by 50% and corrected the OpenSCAD error. I also added some small zip tie slots on the inside edges of the prop guards.
I was hoping I could get away with the zip tie slots, but they ended up being a weak point, and I finally broke the frame when I crashed into a brick wall.
Version 2.0 removes these zip tie slots, and it moves the holes for the nylon standoffs farther away from the props. It also adds zip tie slots to the bottom frame in an attempt to allow for "zip tie landing gear."
The Version 2.0 frame comes in at 58 grams--8 grams lighter than Version 1.0--when printed with 2 top layers, 2 bottom layers, 4 perimeters, and 20% hexagonal infill with a 0.4mm nozzle. This is my lightest frame to date, and I expect it to be the sturdiest!
My all-up-weight is currently 340 grams with an 850mAh 4S LiPo, and FPV camera and transmitter, and using aluminum screws. The PH145 feels fast and agile with this small battery, and it can usually fly for about 6 minutes.
I'm running tri-blade RotorX RX3040T props, EMAX RS1306 4000Kv motors, a Naze32, and some sort of 4-in-1 (supposedly) 4x30A ESC. I have a Crazepony 700TVL camera and transmitter mounted on the drone. Without a battery, the PH145 weighs in at 245 grams.
PH145 FPV at Oak Point Park
I'm still learning how to fly in FPV. I'm not very good at it yet!
Parts List:
28 M3 screws 8mm Steel Screws or 8mm Aluminum Screws
M3 25mm Nylon Standoffs
LittleBee 30Ax4 4-in-1 ESC
Naze32
DYS BX1306 4000Kv motors or EMAX RS1306 4000KV
Male XT60 battery connector
RotorX RX3040T Props
Taulman 910 filament 1lb
I'm also running this FPV camera and transmitter:
Eachine 700TVL FPV Camera and Transmitter
Eachine EV800 FPV Goggles
These are other batteries I've tried so far:
Venom 50C 850 mAh - 5+ minutes
GARTT 1500mAh 4S - 9.5 minutes
CrazePony Graphene 1300mAh 4S - 8+ minutes
Floureon 2200mAh 3S - 9+ minutes
1300mAh 3S - 5 to 6 minutes (not the brand I used)
A 1300mAh 3S feels like a great way to get used to the quadcopter. I was flying on a well worn 1300mAh that used to belong to a friend. The quadcopter started to feel a bit weaker as I approached the 5 minute mark, but it was more than usable at 6 minutes of air time. You can run 3S batteries if you already have them, but I highly recommend the 850mAh 4S. I have 5 of them, and they're excellent!
Similar models
3dwarehouse
free
Tattu Lipo 850mAh 75C 14.8V 4S
...tattu lipo 850mah 75c 14.8v 4s
3dwarehouse
ace tattu lipo rechargeable battery 850mah 75c 4s for rc fpv racing drone quadcopter
thingiverse
free
Crazepony 700tvl Lens Cap by hpz937
...crazepony 700tvl lens cap by hpz937
thingiverse
lens cap for the crazepony 700tvl fpv camera
thingiverse
free
Fx230 fpv quadcopter by crysis_ps
...is frame allows to fly with 5 or 6 inch propellers.
for example, for me: 5 inch with 4s batteries and 6 inch - with 3s batteries.
thingiverse
free
Tweety 2.0 - 130 Sized -True X - FPV Racing POD by bitwise
...cam, protivizion made a nice holder for that :http://www.thingiverse.com/thing:1783683 similar setup like below, except different frame :https://www.youtube.com/watch?v=4laigkuyhgohttps://www.youtube.com/watch?v=5cyg44brk1ehttps://www.youtube.com/watch?v=kotx4jrn3so recomended setup...
thingiverse
free
Lord Helmchen by Netfusion
...uot;lord helmchen" is a 120mm size fpv quadcopter with 3inch props and a weight of about 235g with 4s 850mah and 1306 motors
thingiverse
free
Tray for 10 LiPo 4S 1300mAh batteries by DiAleksi
...ah batteries to fit nicely into lowepro bp x1/x2/x3 drone backpack. i use turnigy's graphene batteries.
slots are 36x36x60mm.
thingiverse
free
DJ105, 105mm brushless quadcopter by DirtyJ_Designs
...t source for colored nylon hardware. http://www.multirotormania.com/80-colored-nylon-
https://www.youtube.com/watch?v=lmnwcqtttro
thingiverse
free
X185F by windrides
...eli_s
fc mount: 30-30.5mm
battery: 850-1000mah 3s-4s
weight: 33.2 grams (30% infill, pla)
print time: 2 hours 10 minutes @ 60mm/s
thingiverse
free
atom144 by maulwurfpauli
... 132.5 gr. / 215 gr. with battery
flight time: about 5.5 up to 7.5 minutes
recommended material thickness of the frame is 3.0 mm.
thingiverse
free
RS90 Quadcopter by Naralex
...rs90 quadcopter by naralex
thingiverse
frame for rs90 quadcopter
Patshead
thingiverse
free
Ball Joint Bracket by patshead
...le m3 bolt to to hole the pieces together. it tilts and swivels surprisingly well!
https://www.youtube.com/watch?v=skruttkxfim
thingiverse
free
Logitech C270 Mount for FlashForge Creator Pro by patshead
...and a pair of logitech c270 cameras along with octoprint to record timelapse videos of all our 3d prints at thelab.ms makerspace.
thingiverse
free
Cable Cover for Mount-It Monitor Stand by patshead
...l monitor stand.
3d printed cable cover for my monitor stand at patshead.com
cable cover for mount-it monitor stand at github
thingiverse
free
Clip-on Tablet Stand for a Bluetooth Keyboard by patshead
...r tablets. you have to print two of them to make it work!
tablet keyboard mount at patshead.com
the blender model at github.
thingiverse
free
Tablet Stand for MakerFarm Prusa i3 by patshead
... can control octoprint just fine, so i printed up a pair of little clips to "attach" one of the tablets to the printer.
thingiverse
free
Desk Grommet with USB, AC, and Rj-45 by patshead
.... it's a custom designed desk grommet with 3 ac outlets, 3 usb ports, and an rj-45 jack. but it is made to fit my own desk.
thingiverse
free
1S LiPo Battery Organizer by patshead
...rging unit.
this is a customizer, so you can choose the number of 1s lipo batteries and whether or not to include the usb holder.
thingiverse
free
Monitor Bracket for Debezeled QNIX QX2710 Monitors by patshead
...t](http://blog.patshead.com/2015/02/3d-printed-monitor-bracket.html ) at patshead.com
monitor bracket for qnix qx2710 at github
thingiverse
free
Harambe Buddha by patshead
...ittle and get him to fit that head onto a buddha for us. it didn't take much convincing on our part.
@zappforthat on twitter
thingiverse
free
FiiO E07K Andes USB DAC Desk Mount by patshead
...nt dimensions.
openscad source available at github
desk mount for my fiio e07k at patshead.com
fiio desk holster at youtube.com
Brushless
turbosquid
$4
Brushless motor
...r download as 3ds, dxf, obj, xsi, wrl, fbx, dwg, dae, and skp on turbosquid: 3d models for games, architecture, videos. (1366202)
3d_export
$10
wheel and motor for mars rover
...last project: a mars rover concept. complete wheel and brushless electrical motor designed to attach to an atv or...
3d_export
$100
the volt futuristic ev hypercar
...future ! some design aspects : this is in-wheel (brushless hub) motors vehicle, for each motor the core part...
3d_export
$20
si cantik cargo plane for humanity medicine kit
...used for the tailboom. the electronic components used are brushless motor os 1000kv which can produce thrust 3kgas a...
free3d
free
N6375 Brushless Motor
...n6375 brushless motor
free3d
n6375 brushless motor
thingiverse
free
Tyro 79 brushless key
...tyro 79 brushless key
thingiverse
tyro 79 brushless key
thingiverse
free
Propeller antirotation brushless lock
...propeller antirotation brushless lock
thingiverse
propeller antirotation brushless lock
thingiverse
free
Brushless motor holder by NukeCraft
...brushless motor holder by nukecraft
thingiverse
brushless motor holder for bl3650
thingiverse
free
Brushless motor mount by robotbuilders
...brushless motor mount by robotbuilders
thingiverse
replacement mount for brushless motor.
thingiverse
free
Brushless motor mount by TarsVH
...brushless motor mount by tarsvh
thingiverse
a mount for a 2830 size brushless motor
Quadcopter
3d_export
$5
quadcopter
...quadcopter
3dexport
futuristic quadcopter design.<br>original design davidflo 77
turbosquid
$19
quadcopter
...lty free 3d model quadcopter for download as max, ma, and obj on turbosquid: 3d models for games, architecture, videos. (1591426)
turbosquid
$25
QuadCopter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Quadcopter 3D Model
...quadcopter 3d model
3dexport
quadcopter studio shaders
quadcopter 3d model vortex333 93968 3dexport
3d_export
$5
Quadcopter 3D Model
...quadcopter 3d model
3dexport
quadcopter aircraft helicopter
quadcopter 3d model greatghost 94019 3dexport
3d_export
$18
passenger quadcopter
... a multicopter is an aircraft built according to a helicopter scheme, with three or more rotors. previews rendered with redshift.
turbosquid
$159
Quadcopter Animated.
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$19
Drone Quadcopter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
Drone Quadcopter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$29
Quadcopter
...
questions about the continuation of the collection or the model can be asked here:<br>https://www.artstation.com/evgen_beg
Fpv
turbosquid
$1
FPV VTX Antenna
...e 3d model fpv vtx antenna for download as obj, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1230317)
3d_export
$9
Fpv logo 3D Model
...onogram vehicle part of auto transport 3d model logo emblem detailed high quality badge
fpv logo 3d model rmodeler 59628 3dexport
3d_export
$8
dji fpv battery slot holder
...er for 3 dji fpv batteries. holds perfectly without shaking. need 1 m3 countersunk head bolt. need to print 6 pin, 1 case, 1 cap.
3d_export
$10
fpv camera hd 700tvl
...aterials are logically named<br>the main format is in 3ds max 2009.<br>satisfcation garranteed..<br>thank you !
thingiverse
free
FpV Mount (SOPORTE FPV) by elborjas1987
...fpv mount (soporte fpv) by elborjas1987
thingiverse
this is a fpv mount with the same holes of naza base.
thingiverse
free
fpv by tbutera
...fpv by tbutera
thingiverse
fpv
thingiverse
free
fpv by tbutera
...fpv by tbutera
thingiverse
fpv
thingiverse
free
FPV DRONE ROOSTER DJI FPV PART
...fpv drone rooster dji fpv part
thingiverse
fpv drone rooster dji fpv install part
thingiverse
free
FPV monitor
...tml?rmmds=myorder&cur_warehouse=cn
link for download : https://cults3d.com/fr/mod%c3%a8le-3d/divers/fpv-monitor-ecran-fpv-faf
thingiverse
free
FPV receiver mount for FPV display by petrex
...eceiver mount for fpv display by petrex
thingiverse
aomway receiver mount for field view 777 fpv monitor. with small cable tray.