Thingiverse
Pergo Spa Filter Cage by Pergo
by Thingiverse
Last crawled date: 3 years ago
DIY Replacement Filter Cartridge.
Darn Pool and spa filters are expensive. So I created these. Printed in 2 halves, fill with generic pillow filler or "poly fill", place both halves together and insert into your pool/spa filter holder. There you have it a cheap replacement for those expensive pool filters.
The filter this replaces is 127 mm diameter with a 54 mm hole and 13.25" (336.55 mm) tall.
You can print this if you can print something 170 mm tall.
Some of the numbers this filter are know as are :
FC-2375
PRB25
C-4326
YOU MUST PRINT IN ABS or the cage will degrade in 1-3 months.
DO NOT try to use PLA.
Print with solid base on bed and turn on supports.
I printed it and due to the retraction and slow printing (it took 26 hours to print), It didn't meet my expectations. I will be modifying the design to make it stronger.
UPDATE: New design, thicker, MUCH stronger.
This is the craziest recipe for print settings ever!, but WOW it printed incredible!
Printed in ABS using
Simplify3D users download the .fff profile to print from
[ABS.8 (Pergo FilterPrint).fff] profile that I printed with
.8 mm nozzle
270C (Yes thats right 270c)
.5 mm Layer height (Yes software will complain of this layer height with .8 mm nozzle)
! NO Extraction ! (The stringing helped the print with supports)
30 mm /sec print speed Print was about 8 hrs. 231.5 g of filament
100% infill
3 shells (top bottom & sides)
85c Bed temp, Layer 10-75c Layer 20-70c!! Supports are ONLY ever other layer!!
!Supports with a .8 mm nozzle every layer cause all kinds of problems!
Printed on a Robo3D R1+ (e3Dv6 hotend) WITH NO PLASTIC or Heat cage!
using the 270c I got a perfect print in open air and it's very strong.
Quite a cleanup job popping out all those supports. But mission success, I have a filter in my spa now. Verify one layer of the base before committing the full print. My 54 mm hole didn't fit on the 54 mm spindle. My printer needed calibration to get the size right. To give others some flex room I changed the inner hole to 56 mm in the model. The original filters are slight rubber so they stretch a bit around the spindle, something that ABS can't do.
I'm Printing my 2nd filter now. My spa uses 2 filters, so I have to print 4 of these.
Darn Pool and spa filters are expensive. So I created these. Printed in 2 halves, fill with generic pillow filler or "poly fill", place both halves together and insert into your pool/spa filter holder. There you have it a cheap replacement for those expensive pool filters.
The filter this replaces is 127 mm diameter with a 54 mm hole and 13.25" (336.55 mm) tall.
You can print this if you can print something 170 mm tall.
Some of the numbers this filter are know as are :
FC-2375
PRB25
C-4326
YOU MUST PRINT IN ABS or the cage will degrade in 1-3 months.
DO NOT try to use PLA.
Print with solid base on bed and turn on supports.
I printed it and due to the retraction and slow printing (it took 26 hours to print), It didn't meet my expectations. I will be modifying the design to make it stronger.
UPDATE: New design, thicker, MUCH stronger.
This is the craziest recipe for print settings ever!, but WOW it printed incredible!
Printed in ABS using
Simplify3D users download the .fff profile to print from
[ABS.8 (Pergo FilterPrint).fff] profile that I printed with
.8 mm nozzle
270C (Yes thats right 270c)
.5 mm Layer height (Yes software will complain of this layer height with .8 mm nozzle)
! NO Extraction ! (The stringing helped the print with supports)
30 mm /sec print speed Print was about 8 hrs. 231.5 g of filament
100% infill
3 shells (top bottom & sides)
85c Bed temp, Layer 10-75c Layer 20-70c!! Supports are ONLY ever other layer!!
!Supports with a .8 mm nozzle every layer cause all kinds of problems!
Printed on a Robo3D R1+ (e3Dv6 hotend) WITH NO PLASTIC or Heat cage!
using the 270c I got a perfect print in open air and it's very strong.
Quite a cleanup job popping out all those supports. But mission success, I have a filter in my spa now. Verify one layer of the base before committing the full print. My 54 mm hole didn't fit on the 54 mm spindle. My printer needed calibration to get the size right. To give others some flex room I changed the inner hole to 56 mm in the model. The original filters are slight rubber so they stretch a bit around the spindle, something that ABS can't do.
I'm Printing my 2nd filter now. My spa uses 2 filters, so I have to print 4 of these.
Similar models
thingiverse
free
Strong Arm Hook by frasart
...the end of the hook)
i recommend:
abs and pla - layer height - 0,1mm - with support 2mm
instructions:
more infill = stronger hook
thingiverse
free
Sharpener for knives - nozzle for "DREMEL" by 3D-MPL
...llets for donats:
btc: 3efggicuog6ryty7roccdmfshxrlva9a2p
eth: 0x120a0c53e75f97b4e5e0845c267f54da33a9edce
webmoney: z147898355795
thingiverse
free
Pergo Bird Food Dish by Pergo
...hat have 14 mm bar spacing.
for best results print upright as it would be in the cage (with bottom on the glass) and use supports
grabcad
free
120 mm fan filter for 3D printing
...esn't contain the grid. it's infill with 0 top and 0 bottom layers. in my example it's 40% infill with 0.4 mm nozzle.
thingiverse
free
Simple Sprayer Nozzle (Customizable) by nhorvath
...printing in abs then acetone vapor smoothing it may also result in a stronger part because the shell layers will be better fused.
thingiverse
free
Pergo Phone Tablet Case Opener Tool by Pergo
...;bisket" parts to keep it open while you move to another section of the case.
hope it work for you as well as it did for me.
thingiverse
free
Intex / summer escape Pool pump impeller by wangcheung
...nd pools. my impeller exploded and replacements are expensive. i printed this with abs on an up mini and has help up pretty well.
thingiverse
free
Pool filter plug to garden hose adapter by visionkj
...hoses leak a lot, but this setup is draining my spa very quickly.
print rafted, large side bottom, 80% infill, .3mm layer height.
thingiverse
free
Pergo Singer Sewing machine 401A Thread Spindle by Pergo
... sewing machine 401a thread spindle by pergo
thingiverse
this is a replacement thread spindle for the singer 401a sewing machine
thingiverse
free
Single Switch Plate with Guard by aolshove
...t had to be cleared from the hollow inside of the part but for me it wasn't too bad other than leaving a rough inner surface.
Pergo
thingiverse
free
Pergo Stylis by Pergo
...pergo stylis by pergo
thingiverse
nothing more than a pergo stylis
thingiverse
free
Pergo Med Jars by Pergo
...pergo med jars by pergo
thingiverse
these are great for travel. sealed containers for meds.
thingiverse
free
Pergo Plunge Earrings by Pergo
...pergo plunge earrings by pergo
thingiverse
just a simple earring design i made for the wife.
thingiverse
free
Pergo Snuggle Path Earring by Pergo
...pergo snuggle path earring by pergo
thingiverse
just another earing
thingiverse
free
Pergo B-Mine Earring by Pergo
...pergo b-mine earring by pergo
thingiverse
a little valentines day earring
thingiverse
free
Pergo Mini Scoop by Pergo
..., you need a scoop for that.. well when you can, you make even the silliest of items. ta dah.. i present pergo's mini scooper
thingiverse
free
Pergo Flower Plunge Earring by Pergo
...pergo flower plunge earring by pergo
thingiverse
earring i call it the "flower plunge"
thingiverse
free
Pergo Night Light Shade by Pergo
...pergo night light shade by pergo
thingiverse
print with .4mm nozzle
no supports
no infill (tee hee)
thingiverse
free
Pergo CoverTopNoTextSolderedDisplay by Pergo
... and can't be removed.
do not print the "base" piece this replaces the "top" and "base" pieces.
thingiverse
free
Pergo Cel Tilter by Pergo
...r by pergo
thingiverse
my pole holder was popular where the wife works, but they don't use the pole with it. so i made this.
Spa
3ddd
$1
SPA ACCESSORIES
...spa accessories
3ddd
спа
spa accessories
turbosquid
$26
SPA
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$65
spa
...spa
3dexport
simple rendering of the scene file
3d_export
$65
spa
...spa
3dexport
simple rendering of the scene file
3d_export
$65
spa
...spa
3dexport
simple rendering of the scene file
3d_export
$65
spa
...spa
3dexport
simple rendering of the scene file
3d_export
$65
spa
...spa
3dexport
simple rendering of the scene file
3ddd
$1
Spa.1
...3ddd
кресло , лежак , спа
lejanka za spa centur
3ddd
$1
spa набор
...spa набор
3ddd
spa
vray fur в большинстве случаев рекомендую отключать.
3ddd
free
Spa набор
... полотенце , свеча
декоративный набор для ванной.
Cage
3d_export
$5
cage
...cage
3dexport
cage
archibase_planet
free
Cage
...cage
archibase planet
cage bird cage birdcage
cage 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Cage
...cage
archibase planet
cage bird cage birdcage
cage 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Cage
...cage
archibase planet
cage bird cage birdcage
cage 3 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Cage
...cage
archibase planet
bird's cage cage
cage n020909 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Cage
...cage
archibase planet
cage
cage monte- 3d model for interior 3d visualization.
3d_export
$7
cage
...cage
3dexport
3d cage model
archibase_planet
free
Cage
...cage
archibase planet
cage
cage n270211 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$5
Cage
...ge
turbosquid
royalty free 3d model cage for download as dwg on turbosquid: 3d models for games, architecture, videos. (1224275)
turbosquid
$4
cage
...squid
royalty free 3d model cage for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1368360)
Filter
3d_export
$10
cartridge filter
...cartridge filter
3dexport
cartridge filter
3d_export
$6
Bag filter
...bag filter
3dexport
bag filter
3d_export
$10
of dust filter
...of dust filter
3dexport
3d model of dust filter
3d_export
$10
of bag filter
...of bag filter
3dexport
3d model of bag filter
3d_export
$7
of bag filter
...of bag filter
3dexport
3d model of bag filter
turbosquid
$20
Filter
...ty free 3d model filter for download as ma, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1512887)
3d_export
$10
bag filter
...he ash hopper. when the gas containing fine dust passes through the filter material, the dust is retained and the gas is purified
3ddd
$1
UFI Filter
...ufi filter
3ddd
фильтр , ufi
ufi oil filter
turbosquid
$30
Filter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
filters
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.