Thingiverse
![Paxetary Gears by charlespax](/previews/9071614.jpg)
Paxetary Gears by charlespax
by Thingiverse
Last crawled date: 3 years, 1 month ago
At the NYC Resistor laser cutting class I embedded one of Zach's planetary gears in one of Zach's planetary gears. This design was laser cut from black acrylic and sandwiched between two clear acrylic sheets.
I found that the inner circle in the front layer needed a smaller diameter to rotate smoothly. I also cut a gasket that sits between the front and gear layers. Otherwise the gears always contact both the front and back layers.
After class I took my project to dinner with a few friends where it was an interesting conversation piece.
Someone should turn these gears into something that can be 3-D printed.
I found that the inner circle in the front layer needed a smaller diameter to rotate smoothly. I also cut a gasket that sits between the front and gear layers. Otherwise the gears always contact both the front and back layers.
After class I took my project to dinner with a few friends where it was an interesting conversation piece.
Someone should turn these gears into something that can be 3-D printed.
Similar models
thingiverse
free
![Planetary Gear Box by dsmith9583](/t/5093869.jpg)
Planetary Gear Box by dsmith9583
...planetary gear box by dsmith9583
thingiverse
laser cut planetary gear box project
cg_trader
$3
![Planetary gear set-1 | 3D](/t/8414057.jpg)
Planetary gear set-1 | 3D
...rinting, stl format files are ok;
for laser cutting, dxf files are ok.
more: https://www.tanerxun.com/planetary-gear-system/.html
thingiverse
free
![Cable holder for desk by ronneke](/t/8643600.jpg)
Cable holder for desk by ronneke
...e
it's a cable holder to place between a desk/table and a wall.
initially i made it to be laser cut from 3mm acrylic sheet.
grabcad
free
![LAYERED ACRYLIC ENCLOSURE](/t/5766508.jpg)
LAYERED ACRYLIC ENCLOSURE
...layered acrylic enclosure
grabcad
acrylic pcb enclosure using laser cut acrylic sheet.
thingiverse
free
![Nautilus Gears Acrylic laser cut + 3d print by Quixotic](/t/8885314.jpg)
Nautilus Gears Acrylic laser cut + 3d print by Quixotic
... use acrylic, since i have access to a laser cutter.
i recommend using fine grain sand paper on any of the acrylics sharp edges.
thingiverse
free
![QIDI Tech I (2018) Door](/t/4675694.jpg)
QIDI Tech I (2018) Door
...t perfect, but it is not bad either.
use .100inch or 2.5mm acrylic. follow your laser's normal settings for cutting acrylic.
thingiverse
free
![Nautilus Gear | Laser cut | acrylic by grumpy_scrambler](/t/8248148.jpg)
Nautilus Gear | Laser cut | acrylic by grumpy_scrambler
... | acrylic by grumpy_scrambler
thingiverse
nautilus gears in 8mm acrylic, mounted on a rusty steel plate.
details in the files.
thingiverse
free
![Gearbug #1 by dustinandrews](/t/9050324.jpg)
Gearbug #1 by dustinandrews
...gearbug #1 by dustinandrews
thingiverse
a laser cut mechanical toy based off a planetary gear system.
thingiverse
free
![Nautilus gear with stand - laser cut by FOLKER by Folker](/t/8933645.jpg)
Nautilus gear with stand - laser cut by FOLKER by Folker
...nautilus gear with stand - laser cut by folker by folker
thingiverse
thanks to misha tikh.
my variant. laser cut, acrylic 3mm.
thingiverse
free
![Laser Cut Gear O'Clock by drayde](/t/9060367.jpg)
Laser Cut Gear O'Clock by drayde
...complete, i just did not get it to work yet. the clock work i tried was not able to drive the clock. need to try a different one.
Charlespax
thingiverse
free
![Mushroom by charlespax](/t/9067838.jpg)
Mushroom by charlespax
...mushroom by charlespax
thingiverse
this is a mushroom i made in solidworks to test support material.
thingiverse
free
![Standoff by charlespax](/t/9069479.jpg)
Standoff by charlespax
...standoff by charlespax
thingiverse
this is a standoff created to hold up a friend's monitor.
thingiverse
free
![Gum Stick by charlespax](/t/9069392.jpg)
Gum Stick by charlespax
...gum stick by charlespax
thingiverse
this is a gum stick.
thingiverse
free
![Square Donut by charlespax](/t/9065622.jpg)
Square Donut by charlespax
...square donut by charlespax
thingiverse
this is just a square donut for calibration.
thingiverse
free
![Document holder by charlespax](/t/9055901.jpg)
Document holder by charlespax
...document holder by charlespax
thingiverse
this is a neat little document holder to help when typing.
thingiverse
free
![3DTin Road Map by charlespax](/t/9067593.jpg)
3DTin Road Map by charlespax
...3dtin road map by charlespax
thingiverse
this is a 3d tin road map.
thingiverse
free
![Parametric Filament by charlespax](/t/9069391.jpg)
Parametric Filament by charlespax
...ament by charlespax
thingiverse
this is a parametric filament made with open scad. use it to print as much filament as you need.
thingiverse
free
![Extruder testing panel by charlespax](/t/9058865.jpg)
Extruder testing panel by charlespax
...extruder testing panel by charlespax
thingiverse
this is a panel we use in the makerbot extruder testing rig.
thingiverse
free
![Standoff insertion tool by charlespax](/t/9058862.jpg)
Standoff insertion tool by charlespax
...standoff insertion tool by charlespax
thingiverse
this is one of the tools we use at makerbot to insert the pcb standoffs.
thingiverse
free
![Charles Edward Pax by charlespax](/t/9068955.jpg)
Charles Edward Pax by charlespax
...charles edward pax by charlespax
thingiverse
this is a 3d scan of my face using the makerbot cyclops 3d scanner.
Gears
3d_ocean
$4
![Gears](/t/576226.jpg)
Gears
...gears
3docean
gear gears iron
4 different size of gears
3d_export
$5
![gear](/t/11419276.jpg)
gear
...gear
3dexport
gear
3d_export
free
![Gears](/t/12951838.jpg)
Gears
...gears
3dexport
gears
3d_export
$5
![gear](/t/11928510.jpg)
gear
...gear
3dexport
a simple model of gear
3d_export
$5
![gear](/t/11419633.jpg)
gear
...gear
3dexport
gear for transmission , case machine
3d_ocean
$3
![Gears](/t/923572.jpg)
Gears
...nical parts process steampunk vehicle wheel work
10 different gear models volume 01-10 files: .3ds .c4d .obj note: you need vray
3d_ocean
$1
![Spur Gear](/t/586351.jpg)
Spur Gear
...spur gear
3docean
decoration gear
a typical spur gear
3d_ocean
$4
![Gear wheels](/t/860868.jpg)
Gear wheels
...gear wheels 3docean engine engineering gear gears industry machinery mechanical toothwheel wheel pair of gear wheels...
turbosquid
$9
![Gear](/t/13376324.jpg)
Gear
...gear
turbosquid
royalty free 3d model gear for download as on turbosquid: 3d models for games, architecture, videos. (1712328)
turbosquid
$2
![Gears](/t/13238989.jpg)
Gears
...rs
turbosquid
royalty free 3d model gears for download as ma on turbosquid: 3d models for games, architecture, videos. (1166710)