Similar models
thingiverse
free
Wingnut Wrench by lisatoddsean2006
...wingnut wrench by lisatoddsean2006
thingiverse
wingnut wrench
thingiverse
free
Parametric wingnut by egil
....
note: for a comprehensive gallery of real nuts and bolts with threads, see nut job in http://www.thingiverse.com/thing:193647
thingiverse
free
Wingnut fitting for standard hex bolt by JonDallimore
...wingnut fitting for standard hex bolt by jondallimore
thingiverse
wingnut fitting for standard hex bolt.
thingiverse
free
M3 Wingnut handscrew by pequ
...small as can be diameter vise.
only found too short models or ones that don't hold wingnut in place (=goes through the model)
thingiverse
free
wingnut by m1232
...wingnut by m1232
thingiverse
thingiverse
free
thumbwheel for wingnuts of wanhao duplicator i3 by smcameron
...l, put the wingnuts into the knobs, then put a bit of tape to hold them in, then screw them onto the bed, then take the tape off.
thingiverse
free
Geeetech Wingnut Replacement by hOTmOLd
...t replacement. useful replacement for idlre tensioner in x and y axis and for heatbed leveling without the need of screwdriver...
thingiverse
free
5/16 Wingnuts! by Prattotyper
...se
these are some wingnut adapters for 5/16 (quarter inch thick) nuts. designed by pratt industrial design student brent collins
thingiverse
free
Wingnut Knob by tocsik
...ter. although it's designed for my specific printer, scaling it up or down should make it usable with various sized wingnuts.
thingiverse
free
M8 ThumbScrew by SAW_Minion
...m8 thumbscrew by saw_minion
thingiverse
a small thumbscrew / wingnut
Dddddyck
thingiverse
free
Ceramic Sample Stamps by dddddyck
...mic test tiles. created for the school of fine arts' ceramics studio at grenfell campus, memorial university of newfoundland.
thingiverse
free
Blade Guard Gear for General #90-125 Bandsaw by dddddyck
...aw by dddddyck
thingiverse
this is a replacement gear for the blade guard adjusting mechanism on general model #90-125 bandsaws.
thingiverse
free
Prop Crown by dddddyck
... to align the upper and lower pieces into rings flat on the table so the pieces are all in their right place before final gluing.
thingiverse
free
Open Press Compatible Mods by dddddyck
...allen bolt and m4 nut.
clip-on wingnuts
-these might work for your press if you're using hex bolts. files are available here.
thingiverse
free
Car Design from Fusion 360 Demo by dddddyck
...ade of .090" coat hanger wire. dimensions may need to be adjusted for the axle holes if you're printing this as a model.
thingiverse
free
Open Press Compatible Typesetting Bed by dddddyck
...idth needed to print.
note: i haven't inked or printed this to paper yet, so its all just precision guesswork to this point!
Wingnut
thingiverse
free
Wingnut Wrench by lisatoddsean2006
...wingnut wrench by lisatoddsean2006
thingiverse
wingnut wrench
thingiverse
free
wingnut by m1232
...wingnut by m1232
thingiverse
thingiverse
free
Wingnut Knob by tocsik
...ter. although it's designed for my specific printer, scaling it up or down should make it usable with various sized wingnuts.
thingiverse
free
M3 Wingnut handscrew by pequ
...small as can be diameter vise.
only found too short models or ones that don't hold wingnut in place (=goes through the model)
thingiverse
free
Geeetech Wingnut Replacement by hOTmOLd
...t replacement. useful replacement for idlre tensioner in x and y axis and for heatbed leveling without the need of screwdriver...
thingiverse
free
5/16 Wingnuts! by Prattotyper
...se
these are some wingnut adapters for 5/16 (quarter inch thick) nuts. designed by pratt industrial design student brent collins
thingiverse
free
Wingnut fitting for standard hex bolt by JonDallimore
...wingnut fitting for standard hex bolt by jondallimore
thingiverse
wingnut fitting for standard hex bolt.
thingiverse
free
WingNut by BRNT
...f the arm set building system
this part snaps onto a standard 5/16"-18 hexnut for easy handling and wrenchless manipulation.
thingiverse
free
Various wingnuts by TheMagusMX
...ent you use sometimes the fit is too tight. in those cases you can simply change a little bit the printing scale in your printer.
Parametric
thingiverse
free
parametric by kassidynowak
...parametric by kassidynowak
thingiverse
parametric
thingiverse
free
Parametric Chain
...parametric chain
thingiverse
parametric chain designed in fusion.
thingiverse
free
Parametric Planter
...parametric planter
thingiverse
parametric planter for small succulents and cactus :)
thingiverse
free
Parametric Dice
...parametric dice
thingiverse
parametric dice with rounded corners. can be easily scaled to any size.
thingiverse
free
Parametric Bear by ATEAM_Shapengine
...parametric bear by ateam_shapengine
thingiverse
parametric bear
thingiverse
free
Parametric coil by localkost
...parametric coil by localkost
thingiverse
parametric coil
thingiverse
free
Parametric Washer by lucibrandus
...parametric washer by lucibrandus
thingiverse
parametric washer
thingiverse
free
Parametric hook by peteruithoven
...parametric hook by peteruithoven
thingiverse
parametric hook.
thingiverse
free
[K] parametric screw / "vis parametrable" by RehabLab-Kerpape
...[k] parametric screw / "vis parametrable" by rehablab-kerpape
thingiverse
une vis paramétrable.
a parametric screw.
thingiverse
free
Parametric Headphone Stand
...parametric headphone stand
thingiverse
parametric headphone stand