OpenRC F1 car - 1:10 RC Car by barspin

Last crawled date: 3 years ago

Build guide: http://danielnoree.com/the-openrc-f1-build-guide/
Questions & Answers: http://danielnoree.com/openrc-questions/
OpenRC Electronics: http://danielnoree.com/openrc-electronics/
Consider supporting me on Patreon: https://www.patreon.com/DanielNoree
Complete hardware/electronics lists and kits available here: http://danielnoree.com/openrc-electronics/
Please respect the license under which this project is released. Thank you!
Other OpenR/C Projects:
OpenR/C Quadcopter: http://www.thingiverse.com/thing:793425
OpenR/C Truggy: http://www.thingiverse.com/thing:42198
OpenR/C Touring Car: http://www.thingiverse.com/thing:83024
Add your OpenR/C build to the buildmap: https://zeemaps.com/map?group=1888242
This is the OpenR/C Formula 1 car. It´s the third generation OpenR/C car and this time around focus is on simplicity! You can print everything in PLA except the tires which are done in NinjaFlex! Of course you can print it in any material you like but for those that want to print a car but only have PLA at hand, this is the project for you!
Print the calibration cude to see if you need to finetune your printer for the M3 nuts to fit in their pockets: http://www.thingiverse.com/thing:2297328
A note on the servo saver. It´s designed to be used with PLA, the upper and lower BOM applies force similar to a spring in a convetional servo saver. Of course the pressure depends on the type of material used, infill etc. Fine tuning can be done adding washer under or over the servo saver.
The "Main Turning Vane´s" needs to have it´s lower part trimmed using a "exacto knife". Then slide it in the chassie plate and push it over the "Lid" and it should snap into place-
Parts that need support added:
Front Spoiler.stl
Front.stl
Rear Rim.stl
Rear Wing.stl
Servo Saver Lower.stl
Things to buy:
Ok, obviously you need some filament which you´ll get from your favourite filament supplier.
You also need M3 screws and nuts which you can get at your local hardware store. Check the BOM list for what to get.
Some bearings are needed aswell, check the BOM list or buy a kit from FastEddyBearings.com: http://www.fasteddybearings.com/openrc-f1-sealed-bearing-kit/
Suggestion for electronics: http://danielnoree.com/openrc-electronics/
Google + Community: https://plus.google.com/u/0/communities/112745535856143176146
You can aslo ask questions in the Facebook group: https://www.facebook.com/groups/1111886228841596/
Rain tires designed by Thomas Palm are available here: http://www.thingiverse.com/thing:999257
Low profile rims & tires designed by Thomas Palm are available here: http://www.thingiverse.com/thing:1103751
Short video: https://youtu.be/eTST_g2g2xQ
Please consider supporting me on Patreon: https://www.patreon.com/DanielNoree
Like my FaceBook page - https://www.facebook.com/Daniel-Nor%C3%A9e-576194949211855/
Subscribe to my YouTube channel - https://www.youtube.com/user/DanielNoree2
INSTAGRAM https://www.instagram.com/danielnoree/
TWITTER https://twitter.com/DanielNoree
GOOGLE+ https://plus.google.com/u/1/+DanielNoree
FACEBOOK https://www.facebook.com/daniel.noree
GOOGLE+ OPENRC COMMUNITY https://plus.google.com/communities/112745535856143176146
FACEBOOK OPENRC GROUP https://www.facebook.com/groups/1111886228841596/