Thingiverse
Old Hag by reddadsteve
by Thingiverse
Last crawled date: 3 years, 3 months ago
Old Hag, is based on the Evil Queen character from a 19th-century German fairy tale "Snow White".
The Evil Queen goes down the dungeon to her secret room where she practices her dark magic, complete with a pet raven, and in desperation uses her spell-book and cauldron to mix a potion that transforms her into the Old Hag.
No supports are required. If you have the proper filament colors, no painting is needed.
The assembled model is 250mm tall and is in proportion to my Snow White model.
Enjoy!
...........................................................................................................
Print Instructions:
Supports: No
Resolution: .2mm
Infill: 10%
Notes:**
Refer to the notes below for a few helpful printing and assembly instructions.
...........................................................................................................
Building the model
Colors
Black: (Paramount3D PLA - Black)
eye_blacks (contains two pieces)
eyebrow_right
eyebrow_left
mouth
shoe
..
Black: (Paramount3D PLA - Matte Black)
cloak_bottom
cloak_top
sleeve_right
sleeve_left
hood
..
White: (Paramount3D PLA - White)
eye_white_right
eye_white_left
tooth
hair_right
hair_left
..
Dark Red: (Paramount3D PLA - Hannibal Red)
tongue
..
Red: (Hachbox PLA - True Red)
apple_red_bottom
apple_red_eyes (contains two pieces)
apple_red_nose
..
Light Brown: (Paramount3D PLA - Military Khaki)
eye_brown_right
eye_brown_left
..
Dark Brown: (eSUN ABS - Brown)
apple_stem
..
Skin: (Paramount3D PLA - Universal Beige)
head
hand_right
hand_left
..
Grey: (Paramount3D PLA - Battleship Gray)
sleeve_insert_right
sleeve_insert_left
..
Bright Green: (unknown PLA)
apple_green
..
...........................................................................................................
Printing and assembly tips
Printing tips
1-No supports are required.
2-There are some pieces that may need brims or rafts, use your discretion.
I used brims on the tooth and eye_blacks.
I used a raft on the eyebrow_left/right parts after two failures with a brim.
3-The tooth is quite small, so you make want to print a few in case you lose it. Do not be concerned if the part looks a bit deformed at that size and shape.
..
Assembly tips:
1-Take your time gluing the model together and enjoy the process.
2-I used E6000 sticky craft glue to put this model together. The sticky glue allows more time to position the parts than a fast drying superglue. I have 'fat fingers' and a shaky hand, so the sticky glue works out best for me, especially with small pieces.
3-I suggest gluing in the eye_browns before the eye_whites (with the eye_blacks already glued in). The eye_whites have a bit of play and could accidentally be inserted incorrectly. Look carefully at the pictures.
4-The hood is a snap fit into the cloak_top. Press it in firmly.
5-The tooth is quite small. Be sure that the mouth and tongue are already glued in, with the opening for the tooth aligned. I used a sticky toothpick to place the tooth in and nudged it into a position that looked good. There is no exact fir for this part.
6-The apple green has small indents for the thumb and middle finger so that the apple sits high in the hand, with the apple slightly rotated in the hand.
7-Refer to the assembly diagram in the pictures section as well as the uploaded pictures for putting the model together. The model is meant to be glued.
Do not hesitate to ask questions, feedback is essential to making better models.
The Evil Queen goes down the dungeon to her secret room where she practices her dark magic, complete with a pet raven, and in desperation uses her spell-book and cauldron to mix a potion that transforms her into the Old Hag.
No supports are required. If you have the proper filament colors, no painting is needed.
The assembled model is 250mm tall and is in proportion to my Snow White model.
Enjoy!
...........................................................................................................
Print Instructions:
Supports: No
Resolution: .2mm
Infill: 10%
Notes:**
Refer to the notes below for a few helpful printing and assembly instructions.
...........................................................................................................
Building the model
Colors
Black: (Paramount3D PLA - Black)
eye_blacks (contains two pieces)
eyebrow_right
eyebrow_left
mouth
shoe
..
Black: (Paramount3D PLA - Matte Black)
cloak_bottom
cloak_top
sleeve_right
sleeve_left
hood
..
White: (Paramount3D PLA - White)
eye_white_right
eye_white_left
tooth
hair_right
hair_left
..
Dark Red: (Paramount3D PLA - Hannibal Red)
tongue
..
Red: (Hachbox PLA - True Red)
apple_red_bottom
apple_red_eyes (contains two pieces)
apple_red_nose
..
Light Brown: (Paramount3D PLA - Military Khaki)
eye_brown_right
eye_brown_left
..
Dark Brown: (eSUN ABS - Brown)
apple_stem
..
Skin: (Paramount3D PLA - Universal Beige)
head
hand_right
hand_left
..
Grey: (Paramount3D PLA - Battleship Gray)
sleeve_insert_right
sleeve_insert_left
..
Bright Green: (unknown PLA)
apple_green
..
...........................................................................................................
Printing and assembly tips
Printing tips
1-No supports are required.
2-There are some pieces that may need brims or rafts, use your discretion.
I used brims on the tooth and eye_blacks.
I used a raft on the eyebrow_left/right parts after two failures with a brim.
3-The tooth is quite small, so you make want to print a few in case you lose it. Do not be concerned if the part looks a bit deformed at that size and shape.
..
Assembly tips:
1-Take your time gluing the model together and enjoy the process.
2-I used E6000 sticky craft glue to put this model together. The sticky glue allows more time to position the parts than a fast drying superglue. I have 'fat fingers' and a shaky hand, so the sticky glue works out best for me, especially with small pieces.
3-I suggest gluing in the eye_browns before the eye_whites (with the eye_blacks already glued in). The eye_whites have a bit of play and could accidentally be inserted incorrectly. Look carefully at the pictures.
4-The hood is a snap fit into the cloak_top. Press it in firmly.
5-The tooth is quite small. Be sure that the mouth and tongue are already glued in, with the opening for the tooth aligned. I used a sticky toothpick to place the tooth in and nudged it into a position that looked good. There is no exact fir for this part.
6-The apple green has small indents for the thumb and middle finger so that the apple sits high in the hand, with the apple slightly rotated in the hand.
7-Refer to the assembly diagram in the pictures section as well as the uploaded pictures for putting the model together. The model is meant to be glued.
Do not hesitate to ask questions, feedback is essential to making better models.
Similar models
thingiverse
free
Eeyore by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Prickle by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Eyeball Father in a teacup by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Rosie the Robot by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Elmer Fudd by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
cults
free
Crocodile
...re no left/right differences.
-the model stands nicely on it's own, however a base is included for extra stability if needed.
cults
free
Dogbert
...nto the notch on the body above the nose and glued them into the glasses_arms. it all turned out quite simple to glue into place.
thingiverse
free
Tweety Bird by reddadsteve
...- a number of the left/right parts look quite similar but are actually different. .. assembly tips: 1 -take...
thingiverse
free
Tweety by reddadsteve
...- a number of the left/right parts look quite similar but are actually different. .. assembly tips: 1 -take...
thingiverse
free
Schroeder by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
Reddadsteve
thingiverse
free
Dilbert by reddadsteve
...required. if you have the right filament colors, no painting is needed.
the completed model is 225mm tall after assembly.
enjoy!
thingiverse
free
Dogbert by reddadsteve
...assembly. this model is in proportion to the dilbert, wally and pointy haired boss models that i've previously posted.
enjoy!
thingiverse
free
Hagar the Horrible by reddadsteve
...printing the pieces in the suggested colors. no supports are required.
hagar may look fierce but he is really a pussycat.
enjoy!
thingiverse
free
Rat by reddadsteve
...all after assembly. this model is in proportion to the pig and crocodile models from the comic that i've also posted.
enjoy!
thingiverse
free
Pig by reddadsteve
...tall after assembly. this model is in proportion to the pig and crocodile models from the comic that i've also posted.
enjoy!
thingiverse
free
Crocodile by reddadsteve
...tall after assembly. this model is in proportion to the pig and crocodile models from the comic that i've also posted.
enjoy!
thingiverse
free
Alice by reddadsteve
...n proportion to the dilbert, wally, pointy haired boss and dogbert models from the comic that i've previously posted.
enjoy!
thingiverse
free
Wally by reddadsteve
... is 200mm tall after assembly. this model is in proportion to the dilbert and pointy haired boss models previously posted.
enjoy!
thingiverse
free
Charlie Brown by reddadsteve
...ad luck.
no supports are required. if you have the proper filament colors, no painting is needed.
the model is 140mm tall.
enjoy!
thingiverse
free
Kermit the Frog by reddadsteve
...o supports are required. if you have the proper filament colors, no painting is needed.
the assembled model is 140mm tall.
enjoy!
Hag
turbosquid
$30
Hag Woman
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
sea hag
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$49
Chair Hag Excellence
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$7
Spring swing for a playground Willy Jeep HAGS
...*************************** hope you like it! also check out my other models, just click on my user name to see complete gallery.
3d_export
$55
Witch 3D Model
...witch 3d model 3dexport witch hag sorceress hex people female woman characters halloween horror monsters...
3d_export
$5
Traffic Cone 3D Model
...construction site road side roadside traffic cone 3d model hag 38069...
3d_export
$60
Rigged 1957 Chevrolet 3D Model
...body roll and shift rigged 1957 chevrolet 3d model hag 38059...
3d_export
$15
Witch Hazel 3D Model
...toon old woman bugs bunny daffy duck cartoon halloween hag crone hex witch hazel 3d model download .c4d .max...
unity_asset_store
$13
The Hag
...levate your workflow with the the hag asset from gamester. find this & other characters options on the unity asset store.
unrealengine
$35
Witch Hag
...witch hag
unreal engine marketplace
collection of hand crafted creepy witch hag animations suited for an enemy npc
Old
turbosquid
$17
Old
...old
turbosquid
royalty free 3d model old for download as on turbosquid: 3d models for games, architecture, videos. (1646242)
3d_ocean
$9
Old phone
...old phone
3docean
classic old phone phone
classic old phone
3d_ocean
$15
Old telephone
...old telephone
3docean
old phone telephone
old telephone v-ray render
3d_ocean
$3
Old Ambry
...old ambry
3docean
ambry furniture highpoly old
old ambry made in high detail.
3ddd
free
Old England
...nd
3ddd
old england , смеситель
двухрычажный смеситель old england. производство италия.
3d_export
$20
the old man
...the old man
3dexport
the old man.
3d_export
$5
an old trailer
...an old trailer
3dexport
an old trailer
3d_export
$5
old tv
...old tv
3dexport
old tv
3d_export
$5
old iron
...old iron
3dexport
old iron
3d_export
$5
Old TV
...old tv
3dexport
old tv