Thingiverse
NXPhlite V3RC15 Enclosure by igalloway
by Thingiverse
Last crawled date: 3 years ago
NXPhlite V3RC15 HoverGames
UPDATED 8/20/2018 - Revised files with reset button
NXPPHILITE3top v2
NXPPHILITE3_bottom v14
Reset Button
Note -Photos of orange version are the older version
[Includes STEP file source format to allow editing]
This is an enclosure for an experimental flight controller (FMU) from NXP Semiconductor that is Linux Foundation Dronecode.org PX4.io software compliant. It follows Dronecode.org connectorization standards. NXPhlite includes two wire automotive ethernet interfaces and CAN bus in addition to the traditional UARTS, SPI and I2C that is typical of PX4 (Pixhawk) type controllers.
Drone software is NuttX and PX4.io FMU.
The board is based on a Kinetis K66 MCU with 2M memory, and has accelerometer, Gyro, magnetometer, and barometric sensors on board. There are lots of other interfaces (UART, GPS, IRDA, Ultrasonic, PWM, etc) and could easily be used with bare metal code, the Kinetis SDK, and other RTOSs like FreeRTOS.
Suitable for Drones of all configurations, Rovers and other robotic systems.
Credit goes to Herminio Menchaca from the NXP Guadalajara team for the designGreat job Herminio!
This design is a work in progress
Website: https://www.HoverGames.com
Video : https://www.youtube.com/watch?v=xLfMEuMjAZE
Documentation : https://nxp.gitbook.com/hovergames
Website: https://www.nxp.com/HoverGamesDrones
Website: https://www.nxp.com/HoverGames
UPDATED 8/20/2018 - Revised files with reset button
NXPPHILITE3top v2
NXPPHILITE3_bottom v14
Reset Button
Note -Photos of orange version are the older version
[Includes STEP file source format to allow editing]
This is an enclosure for an experimental flight controller (FMU) from NXP Semiconductor that is Linux Foundation Dronecode.org PX4.io software compliant. It follows Dronecode.org connectorization standards. NXPhlite includes two wire automotive ethernet interfaces and CAN bus in addition to the traditional UARTS, SPI and I2C that is typical of PX4 (Pixhawk) type controllers.
Drone software is NuttX and PX4.io FMU.
The board is based on a Kinetis K66 MCU with 2M memory, and has accelerometer, Gyro, magnetometer, and barometric sensors on board. There are lots of other interfaces (UART, GPS, IRDA, Ultrasonic, PWM, etc) and could easily be used with bare metal code, the Kinetis SDK, and other RTOSs like FreeRTOS.
Suitable for Drones of all configurations, Rovers and other robotic systems.
Credit goes to Herminio Menchaca from the NXP Guadalajara team for the designGreat job Herminio!
This design is a work in progress
Website: https://www.HoverGames.com
Video : https://www.youtube.com/watch?v=xLfMEuMjAZE
Documentation : https://nxp.gitbook.com/hovergames
Website: https://www.nxp.com/HoverGamesDrones
Website: https://www.nxp.com/HoverGames
Similar models
thingiverse
free
NXPhlite GPS Mast mount for HoverGames Drone S500 by igalloway
...itbook.com/book/nxphlite-team/prototype-nxphlite/details
website: https://www.nxp.com/uav
website: https://www.nxp.com/hovergames
thingiverse
free
HoverGames DCD-LZ-ADAPT Debugger SWD (JTAG) adapter board case (NXPhlite) by igalloway
...itbook.com/book/nxphlite-team/prototype-nxphlite/details
website: https://www.nxp.com/uav
website: https://www.nxp.com/hovergames
thingiverse
free
HoverGames Drone Antenna rails bracket (NXPhlite) by igalloway
...itbook.com/book/nxphlite-team/prototype-nxphlite/details
website: https://www.nxp.com/uav
website: https://www.nxp.com/hovergames
thingiverse
free
FlySky i6S Transmitter stick and switch protector by igalloway
...itbook.com/book/nxphlite-team/prototype-nxphlite/details
website: https://www.nxp.com/uav
website: https://www.nxp.com/hovergames
thingiverse
free
Hovergames Drone GoPro Mount by PruneFace
...hovergames drone gopro mount by pruneface
thingiverse
gopro mount for the nxp hovergames drone.
thingiverse
free
SMA Antenna Drone Mount S500 NXP Hovergames
...hovergames
thingiverse
sma mounting hardware for drones.
compatible with nxp hovergames.
30mm clearance under the mounting hole.
grabcad
free
Hovergames Galileo
...hovergames galileo
grabcad
cad files of aditional parts attached to nxp drone.
thingiverse
free
NXP Hovergames Drone Double GoPro Mount by PruneFace
...his is a double sided mount for mounting two gopro snap-in items onto the nx hovergames drone. it slides over the mounting rails.
thingiverse
free
NavQ Case for Hovergames Drone by Kayboku
...ase i designed for the navq for the nxp hovergames. i may still make some improvements so i will upload the new files when ready.
thingiverse
free
Battery Bracket for the hovergames drone by Kayboku
...derneath the nxp hovergames drone. then the 2 carbon fibre rods are mounted and the camera can be mounted underneath the battery.
Nxphlite
thingiverse
free
NXPhlite GPS Mast mount for HoverGames Drone S500 by igalloway
...itbook.com/book/nxphlite-team/prototype-nxphlite/details
website: https://www.nxp.com/uav
website: https://www.nxp.com/hovergames
thingiverse
free
HoverGames DCD-LZ-ADAPT Debugger SWD (JTAG) adapter board case (NXPhlite) by igalloway
...itbook.com/book/nxphlite-team/prototype-nxphlite/details
website: https://www.nxp.com/uav
website: https://www.nxp.com/hovergames
thingiverse
free
HoverGames Drone Antenna rails bracket (NXPhlite) by igalloway
...itbook.com/book/nxphlite-team/prototype-nxphlite/details
website: https://www.nxp.com/uav
website: https://www.nxp.com/hovergames
thingiverse
free
FlySky i6S Transmitter stick and switch protector by igalloway
...a work in progress video : https://www.youtube.com/watch?v=xlfmeumjaze documentation : https://www.gitbook.com/book/nxphliteteam/prototype-nxphlite/details website: https://www.nxp.com/uav website:...
Igalloway
thingiverse
free
HoverGames Drone frame model by igalloway
...odel was provided to us by a third party. it may be helpful for developing accessories or creating a simulation model in ros etc.
thingiverse
free
Screen Door Replacement Handle by igalloway
... the sun, wind, cold and weather.
i've included the original autocad fusion 360 source files, as well as iges and step files.
thingiverse
free
Clip to hold two 60.5mm diameter ABS pipes 100mm apart. by igalloway
... to hold multiple pipes!
100mm center to center of the pipes
this is just a custom thing i wanted. it is not for anything common.
thingiverse
free
Jig-clip Stand for 2" ABS pipe by igalloway
...d next to each other. i had a need for this. i have no idea what you might use this for, but you are welcome if it helps somehow.
thingiverse
free
Orthogone GPS LORA BLE tracker by igalloway
...s attached, and the lora radio and gps antenna cable just sticks out the slot. the little lipo battery sits underneath the board.
thingiverse
free
Raise3D Filament feed grommet for Acrylic door by igalloway
...gh to put some nylon tubing through, which i only did 'cause i thought it looked nice. the nylon tube is totally unnecessary.
thingiverse
free
HoverGames Drone Antenna rails bracket (NXPhlite) by igalloway
...itbook.com/book/nxphlite-team/prototype-nxphlite/details
website: https://www.nxp.com/uav
website: https://www.nxp.com/hovergames
thingiverse
free
FlySky i6S Transmitter stick and switch protector by igalloway
...itbook.com/book/nxphlite-team/prototype-nxphlite/details
website: https://www.nxp.com/uav
website: https://www.nxp.com/hovergames
thingiverse
free
NXPhlite GPS Mast mount for HoverGames Drone S500 by igalloway
...itbook.com/book/nxphlite-team/prototype-nxphlite/details
website: https://www.nxp.com/uav
website: https://www.nxp.com/hovergames
Enclosure
3d_export
free
electrical enclosure
...l enclosure where electrical devices like (relays, contactors, busbars ) are kept in order to protect from hazardous environment.
turbosquid
$100
GPU Enclosure
...yalty free 3d model gpu enclosure for download as obj and stl on turbosquid: 3d models for games, architecture, videos. (1381061)
3d_export
$5
Electrical Enclosure
...ed. also has tower lights attaced on the top.<br>file format that are available:<br>.step<br>.obj<br>.stl
archive3d
free
Enclosure 3D Model
...closure 3d model
archive3d
shower enclosure-acquarius- 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-omega- 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-vega - 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-zenith - 3d model for interior 3d visualization.
turbosquid
$20
shower enclosure
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$14
Dumpster Enclosure
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$25
3d printer enclosure
... model 3d printer enclosure for download as ipt, skp, and fbx on turbosquid: 3d models for games, architecture, videos. (1634310)