Thingiverse
NoTankS - 3D Printed RC Tank by swepet
by Thingiverse
Last crawled date: 3 years ago
Introduction:
Introduction video: https://youtu.be/maQO2Yl2V8M
It was my good friend Scott that got me interested in 3D printed RC tanks.
He sent me a couple of youtube links with very cool tanks.
I was inspired by the "RC Speed tank" by Bryant87https://www.thingiverse.com/thing:2024364
and also "RC Tank" by Staindhttps://www.thingiverse.com/thing:2414983
I though they were really cool, like Terrascout nerf tanks on steroids.
But i wanted a enclosed tank, more resistant to weather, for future robotics FPV projects.
So i started drawing my on tank in Fusion 360. I started from scratch so my parts will not be compatible with the other tanks.
About my design:
My goals was to have it enclosed, have as few non 3d printed parts as possible, have a simple design that is easily printed with as little support material as possible.
Everything is designed around the wheel screws. The screws holds the wheels, act as hinges, mounts the battery tray, and locks the covers. I have even made a small tool to help when working with the screws.
The design is also modular. The battery holder can easy be redesigned to hold different batteries. The covers can be redesigned to hold camera, have more ventilation etc.
The bottom and the covers are designed to be printed on the side, that is why the nut holes are angled, so that no support is needed.
The track segments doesn't need screws and nuts, they are put together by pressfitting
cut to length pieces of 3mm nylon filament. The track segments also have a slot in them, that is for being able to fit different grip insert, like a TPU insert for more traction on slippery surfaces, or sharp teeth for more outdoor traction.
I have included a step file :-)
Things you will need:
2x motor and esc combo, 80Thttps://www.banggood.com/540-Motor-60A-ESC-Carbon-Brushed-110-RC-Crawler-Shaft-3_175mm-RC-Car-Parts-p-1187553.html
2x Zippy Compact 3700mAh 3s batteries (or your own battery of choice)https://hobbyking.com/en_us/zippy-compact-3700mah-3s-25c-lipo-pack.html
24x 8x22x7mm Ball Bearings (standard skateboard bearings)https://www.banggood.com/10pcs-ABEC-7-608ZZ-8x22x7mm-Ball-Bearings-Deep-Groove-Ball-Bearing-p-1185033.html
2x 11T M1 5mm Pinion Gearhttps://hobbyking.com/en_us/11t-5mm-m1-hardened-steel-pinion-gear-1pc.html
and
2x 5mm to 3.2mm pinion adapterhttps://www.banggood.com/HOBBYWING-Motor-Axle-3_17mm-To-5mm-Change-over-Shaft-Adapter-p-927457.html (might even be possible to print)
or
2x 12T 3.2mm Pinion Gearhttps://www.conrad.se/St%e5lkugghjul-Reely-523-3,2-STAHL-Modul-typ-1.0-Borrdiameter-3.2-mm-Antal-t%e4nder-12.htm?websale8=conrad-swe&pi=240362
12x M6 70mm Hex bolt
12x M6 Nut
8x M3 10mm screw (for the motors)
2x velcro strap for holding batteries
3mm nylon filament (or other types of 3mm filament)http://taulman3d.com/618-features.html
Your own RC radio and receiver, preferably on that supports tank mixing.https://hobbyking.com/en_us/frsky-2-4ghz-accst-taranis-x9d-plus-digital-telemetry-radio-system-mode-2.html
A couple of zipties
Battery connectors
How to print:
I have printed everything in regular PLA.
Track segments are printed with 100% infill everything else with 20%.
The covers and bottom are designed to be printed on its side, a little brim is a good idea.
notanks_v1_bottom_wheel.stl need support material.
notanks_v1_front_cover.stl needs touching buildplate support
Things you need to print multiple of:
2x notanks_v1_drive_wheel_55t.stl if you use 12t pinion for motor.
2x notanks_v1_drive_wheel_56t.stl if you use 11t pinion for motor.
82x notanks_v1_track.stl
8x notanks_v1_bottom_wheel.stl
2x notanks_v1_front_wheel.stl
24x notanks_v1_wheel_insert.stl
2x notanks_v1_outside.stl
2x notanks_v1_inside.stl (mirror one when printing)
(now there also are alternative full covered notanks_v2_outside_snow.stl and
notanks_v2_inside_snow.stl , if you have a larger printbed)
How to assemble:
Tool
Print the included tool, it makes the job building easier then using a wrench. It is also great to have when out in the field driving.
Wheels:
Two ball bearings are press fitted into each wheels, a vise is a good tool for that.
A wheel insert is then fitted into each ball bearing in the wheels, that is two per wheel.
Be in mind that if you have chosen to use the 11 teeth motor pinion gear you will need the 56 teeth drive wheel, if you have chosen the 12 teeth motor gear then you will need the 55 teeth drive gear.
Bottom, Cover and sides:
The nuts are press fitted into the holes using a screw from the other side to drag them in.
Motors:
Attache pinion gears (and adapters) to motors. Screw the motors to the inside parts.
Sides:
Put the long bolts into the outside parts, put the wheels on the bolts. Front wheel in the front and drive wheel on top. Put the inside part with the motor on the bolts and screw in the drive wheel bolt.
Bottom
Screw the now assembled sides onto the bottom part. Before thightening the screws, insert the rc holder part, between the slots in the insides.
Covers
Screw on the front and back cover.
The tracks:
The track segments is put together by pressing in pieces of 3mm nylon filament.
41 segments per track,. When mounting the tracks it is easiest to remove the back wheel push it forward and then tighten the track when the back wheel is pushed back and mounted. It is going to be very thigh first, but loosens a little bit over time when driving. But you might even want to start with 42 segments per track. For easy disassemble you can leave one filament piece a bit longer sticking out some millimeter so that it can be grabbed by pliers.
Battery holder:
Unscrew the two bottom middle bolts a little bit, mount the battery holder and fasten it by screwing in the bolts again. Attach a velcro strap to the slots in the battery holder for holding batteries.
Electronics:
Solder the wires to the motors. Battery connectors to the ESC:s. Mount the ESC:s and receivers onto the rc holder using zipties. Connect wires and fasten the wires to the holder with zipties.
RC:
Program your radio with a good tank mix, go out and have fun.
Warnings / Future upgrades
Caution when driving in the winter:
(Now fixed, alternative full cover sides available, see updates below)
Snow can build up and get the tracks stuck. That is what happened to me once, i was >using a 35T motor and when the track got stuck the motor draw to much current and >burned up. In future upgrades I will make the inside and outside part bigger to cover the >wheels completely to limit snow from getting in to the tracks.
Heat:
When i have tested the tank it is in the middle of the Swedish winter, with temperatures >blow zero degree Celsius. If driving in warmer locations, perhaps ventilation for the motors >and escs are required. I have thought about making changes to front and back cover to >allow mounting a 40mm fan on each side, for better cooling, and if so the inlet will be >angled backwards to prevent dirt from getting in, but that is for later considerations.
Drive wheel:
I have experimented with having the driving on the front wheel, an even on the front and >top wheel at the same time, but it seams having just the top wheel is less sensitive to dirt >and stuff locking up the tracks. I have seen a design on thingiverse that have a planetary >gear built into the drive wheel, that might be wort a try in the future.
Updates:
2018-09-22
First FPV test over 4G LTE, using a raspberry pi zero w and a 4G LTE Wifi routerhttps://www.youtube.com/watch?v=8x5hJwNIOas
Added files:
notanks_fpv1_pizero.stl and notanks_fpv1_backpack.stl
and notanks_fpv1_drive.py that is the control program
2018-04-08
Made a youtube video about the upgrades:https://www.youtube.com/watch?v=ycGbiYwoBRY
2018-04-04
Added Inserts for the tracks, i printed mine in red PLA, looks great and gives more traction, especially in snow. See the picture for how awesome it no looks :-)
File added: notanks_v2_track_insert.stl
2018-04-02
I have added alternative full cover sides, to prevent snow and dirt getting into the tracks, se the latest picture added. They are a bit bigger then standard printer bed size can handle. I did mine on my CR-10S (300x300mm bed).
The files added are:
notanks_v2_inside_snow.stl
notanks_v2_outside_snow.stl
2018-02-15
The battery i used was discontinued:https://hobbyking.com/en_us/zippy-compact-4000mah-3s-25c-lipo-pack.html
I changed it to this, should also work:https://hobbyking.com/en_us/zippy-compact-3700mah-3s-25c-lipo-pack.html
Keep in mind that any not to small and weak 3s battery shold work, i just used old batteries i had laying around.. :-)
Introduction video: https://youtu.be/maQO2Yl2V8M
It was my good friend Scott that got me interested in 3D printed RC tanks.
He sent me a couple of youtube links with very cool tanks.
I was inspired by the "RC Speed tank" by Bryant87https://www.thingiverse.com/thing:2024364
and also "RC Tank" by Staindhttps://www.thingiverse.com/thing:2414983
I though they were really cool, like Terrascout nerf tanks on steroids.
But i wanted a enclosed tank, more resistant to weather, for future robotics FPV projects.
So i started drawing my on tank in Fusion 360. I started from scratch so my parts will not be compatible with the other tanks.
About my design:
My goals was to have it enclosed, have as few non 3d printed parts as possible, have a simple design that is easily printed with as little support material as possible.
Everything is designed around the wheel screws. The screws holds the wheels, act as hinges, mounts the battery tray, and locks the covers. I have even made a small tool to help when working with the screws.
The design is also modular. The battery holder can easy be redesigned to hold different batteries. The covers can be redesigned to hold camera, have more ventilation etc.
The bottom and the covers are designed to be printed on the side, that is why the nut holes are angled, so that no support is needed.
The track segments doesn't need screws and nuts, they are put together by pressfitting
cut to length pieces of 3mm nylon filament. The track segments also have a slot in them, that is for being able to fit different grip insert, like a TPU insert for more traction on slippery surfaces, or sharp teeth for more outdoor traction.
I have included a step file :-)
Things you will need:
2x motor and esc combo, 80Thttps://www.banggood.com/540-Motor-60A-ESC-Carbon-Brushed-110-RC-Crawler-Shaft-3_175mm-RC-Car-Parts-p-1187553.html
2x Zippy Compact 3700mAh 3s batteries (or your own battery of choice)https://hobbyking.com/en_us/zippy-compact-3700mah-3s-25c-lipo-pack.html
24x 8x22x7mm Ball Bearings (standard skateboard bearings)https://www.banggood.com/10pcs-ABEC-7-608ZZ-8x22x7mm-Ball-Bearings-Deep-Groove-Ball-Bearing-p-1185033.html
2x 11T M1 5mm Pinion Gearhttps://hobbyking.com/en_us/11t-5mm-m1-hardened-steel-pinion-gear-1pc.html
and
2x 5mm to 3.2mm pinion adapterhttps://www.banggood.com/HOBBYWING-Motor-Axle-3_17mm-To-5mm-Change-over-Shaft-Adapter-p-927457.html (might even be possible to print)
or
2x 12T 3.2mm Pinion Gearhttps://www.conrad.se/St%e5lkugghjul-Reely-523-3,2-STAHL-Modul-typ-1.0-Borrdiameter-3.2-mm-Antal-t%e4nder-12.htm?websale8=conrad-swe&pi=240362
12x M6 70mm Hex bolt
12x M6 Nut
8x M3 10mm screw (for the motors)
2x velcro strap for holding batteries
3mm nylon filament (or other types of 3mm filament)http://taulman3d.com/618-features.html
Your own RC radio and receiver, preferably on that supports tank mixing.https://hobbyking.com/en_us/frsky-2-4ghz-accst-taranis-x9d-plus-digital-telemetry-radio-system-mode-2.html
A couple of zipties
Battery connectors
How to print:
I have printed everything in regular PLA.
Track segments are printed with 100% infill everything else with 20%.
The covers and bottom are designed to be printed on its side, a little brim is a good idea.
notanks_v1_bottom_wheel.stl need support material.
notanks_v1_front_cover.stl needs touching buildplate support
Things you need to print multiple of:
2x notanks_v1_drive_wheel_55t.stl if you use 12t pinion for motor.
2x notanks_v1_drive_wheel_56t.stl if you use 11t pinion for motor.
82x notanks_v1_track.stl
8x notanks_v1_bottom_wheel.stl
2x notanks_v1_front_wheel.stl
24x notanks_v1_wheel_insert.stl
2x notanks_v1_outside.stl
2x notanks_v1_inside.stl (mirror one when printing)
(now there also are alternative full covered notanks_v2_outside_snow.stl and
notanks_v2_inside_snow.stl , if you have a larger printbed)
How to assemble:
Tool
Print the included tool, it makes the job building easier then using a wrench. It is also great to have when out in the field driving.
Wheels:
Two ball bearings are press fitted into each wheels, a vise is a good tool for that.
A wheel insert is then fitted into each ball bearing in the wheels, that is two per wheel.
Be in mind that if you have chosen to use the 11 teeth motor pinion gear you will need the 56 teeth drive wheel, if you have chosen the 12 teeth motor gear then you will need the 55 teeth drive gear.
Bottom, Cover and sides:
The nuts are press fitted into the holes using a screw from the other side to drag them in.
Motors:
Attache pinion gears (and adapters) to motors. Screw the motors to the inside parts.
Sides:
Put the long bolts into the outside parts, put the wheels on the bolts. Front wheel in the front and drive wheel on top. Put the inside part with the motor on the bolts and screw in the drive wheel bolt.
Bottom
Screw the now assembled sides onto the bottom part. Before thightening the screws, insert the rc holder part, between the slots in the insides.
Covers
Screw on the front and back cover.
The tracks:
The track segments is put together by pressing in pieces of 3mm nylon filament.
41 segments per track,. When mounting the tracks it is easiest to remove the back wheel push it forward and then tighten the track when the back wheel is pushed back and mounted. It is going to be very thigh first, but loosens a little bit over time when driving. But you might even want to start with 42 segments per track. For easy disassemble you can leave one filament piece a bit longer sticking out some millimeter so that it can be grabbed by pliers.
Battery holder:
Unscrew the two bottom middle bolts a little bit, mount the battery holder and fasten it by screwing in the bolts again. Attach a velcro strap to the slots in the battery holder for holding batteries.
Electronics:
Solder the wires to the motors. Battery connectors to the ESC:s. Mount the ESC:s and receivers onto the rc holder using zipties. Connect wires and fasten the wires to the holder with zipties.
RC:
Program your radio with a good tank mix, go out and have fun.
Warnings / Future upgrades
Caution when driving in the winter:
(Now fixed, alternative full cover sides available, see updates below)
Snow can build up and get the tracks stuck. That is what happened to me once, i was >using a 35T motor and when the track got stuck the motor draw to much current and >burned up. In future upgrades I will make the inside and outside part bigger to cover the >wheels completely to limit snow from getting in to the tracks.
Heat:
When i have tested the tank it is in the middle of the Swedish winter, with temperatures >blow zero degree Celsius. If driving in warmer locations, perhaps ventilation for the motors >and escs are required. I have thought about making changes to front and back cover to >allow mounting a 40mm fan on each side, for better cooling, and if so the inlet will be >angled backwards to prevent dirt from getting in, but that is for later considerations.
Drive wheel:
I have experimented with having the driving on the front wheel, an even on the front and >top wheel at the same time, but it seams having just the top wheel is less sensitive to dirt >and stuff locking up the tracks. I have seen a design on thingiverse that have a planetary >gear built into the drive wheel, that might be wort a try in the future.
Updates:
2018-09-22
First FPV test over 4G LTE, using a raspberry pi zero w and a 4G LTE Wifi routerhttps://www.youtube.com/watch?v=8x5hJwNIOas
Added files:
notanks_fpv1_pizero.stl and notanks_fpv1_backpack.stl
and notanks_fpv1_drive.py that is the control program
2018-04-08
Made a youtube video about the upgrades:https://www.youtube.com/watch?v=ycGbiYwoBRY
2018-04-04
Added Inserts for the tracks, i printed mine in red PLA, looks great and gives more traction, especially in snow. See the picture for how awesome it no looks :-)
File added: notanks_v2_track_insert.stl
2018-04-02
I have added alternative full cover sides, to prevent snow and dirt getting into the tracks, se the latest picture added. They are a bit bigger then standard printer bed size can handle. I did mine on my CR-10S (300x300mm bed).
The files added are:
notanks_v2_inside_snow.stl
notanks_v2_outside_snow.stl
2018-02-15
The battery i used was discontinued:https://hobbyking.com/en_us/zippy-compact-4000mah-3s-25c-lipo-pack.html
I changed it to this, should also work:https://hobbyking.com/en_us/zippy-compact-3700mah-3s-25c-lipo-pack.html
Keep in mind that any not to small and weak 3s battery shold work, i just used old batteries i had laying around.. :-)
Similar models
thingiverse
free
Enclosure for 3 compact zippy with bms
...oard that will supposedly fit 3 zippy compact 3s battery.
https://hobbyking.com/en_us/zippy-compact-5000mah-3s-25c-lipo-pack.html
thingiverse
free
swamp boat by joeytvr
...at is fast and fun. i also used different motor. https://hobbyking.com/en_us/m1806r-brushless-motor-for-rc-model-aircraft-cw.html
thingiverse
free
DNA250 1800mAh Lipo box by UKDTweak
...1mm thick by 3mm by 8mm, n52 magnets, total of 8 required
the 510 hole is 10mm to suit the varitube 510's.
h120mm-d28mm-w59mm
thingiverse
free
Team Associated B6D 3S Battery Holder by Pesle
...wn transmission in the b6, b6.1 or b6.1d
the 3s it fits is this:https://hobbyking.com/en_us/turnigy-2200mah-3s-30c-lipo-pack.html
thingiverse
free
Mini Ripsaw Robot tank tracked lower cover by bolbot
...rect drive, without reduction gear.https://hobbyking.com/en_us/hobbykingr-tm-brushless-car-esc-30a-w-reverse.html/?___store=en_us
thingiverse
free
Battery container [F450,F550,S450,S550] by mboros001
...ing.com/en_us/turnigy-5000mah-3s-30c-lipo-pack.html
fasteners you need:
-8pc m3x20 bolt
-1pc m4x20 hex head bolt
-1pc m4 hex nut
thingiverse
free
NTM Prop Drive 28 Series Firewall / Motor Mount by zachjones27
... in order to prevent the bolts from digging in to the edge.
i printed in pla with 50% infill, has already survived a few crashes.
3dwarehouse
free
Zippy 2200mah 3S
...l of a zyppy compact 2200mah 3s lipo battery. #2200 #2200mah #25c #3s #akku #battery #compact #hobbyking #lipo #lipoly #rc #zippy
thingiverse
free
Battery cover for the rc tank by nero2387
...battery cover for the rc tank by nero2387
thingiverse
battery cover for 2 x 3s 2200mah lipo
thingiverse
free
Improved Track Drive Wheel for RC Tank by Oger
...ot tested this drive wheel with a fast setup. right now i am using a very slow high torque setup with geared motors for crawling.
Notanks
thingiverse
free
NoTanks FPV - BigFan + FPV Camera by MatiasV
...w.tinkercad.com/things/ggavhcm3cwv-notanks-fpv-front-coverhttps://www.tinkercad.com/things/0zv43rmgejk-notanks-backcover-80mm-fan
thingiverse
free
NoTanks STL to defalt freecad solid
...ined the mesh and checked it then converted to solid fpv mount is the only one with errors. they could be exported as step or stl
thingiverse
free
notanks tank array robot platform mount
...w broom, cart, vacume, rasbery pi fpv, arduino sensors...
original stl stiched to shape .1" simplified and modeled as solid.
thingiverse
free
NoTankS Makerblock 87050 Track Mod
...www.aliexpress.com/item/32888435164.html
thanks swepet for making your design available.https://www.thingiverse.com/thing:2789361
Swepet
thingiverse
free
Bikers cookie cutter by swepet
...bikers cookie cutter by swepet
thingiverse
my mother and father are bikers. i gave them some cool cookies for the holidays..
thingiverse
free
Flexible PLA test by swepet
...
thingiverse
testing flexible pla. tank tracks, wheel with tire, and a flexible joint.http://www.youtube.com/watch?v=bb5l_jhyong
thingiverse
free
Rails for LowRider2 CNC by swepeter
...this:https://www.thingiverse.com/thing:2368805
thanks godler
alos modded the y plate fromhttp://www.thingiverse.com/thing:3064287
thingiverse
free
PL2Q Hugin by swepet
...creatures naming-scheme here is the pl2q hugin. i have put a lot of thought in to this one, but i fear it will fly away one day..
thingiverse
free
IP camera mount for Ultimaker by swepet
...for the ultimaker.
uses a $50 ip camera from ebay.
perfect to be able to have an eye on the 3d print while away from the machine.
thingiverse
free
iPhone GoPro head-strap mount by swepet
... be able to record video hands free, or watch movies etc.. and you will look very cool.http://www.youtube.com/watch?v=i73-y4gxddq
thingiverse
free
PL1Q Vampire, the 3d printable quadcopter by swepet
...
its a 3d printable quadcopter frame that i have designed, all parts is printable. see http://www.youtube.com/watch?v=dlrn-lrltus
thingiverse
free
Flexible jalousie sliding door concept, PLA by swepet
...t showing that pla can be flexible and that it can be useful for sliding doors etc.. would also be a nice lamp screen i think :-)
thingiverse
free
FPV RSSI SWITCH, 5-port by swepet
...om the receiver with the best reception, so that you can have multiple directional antennas pointing at different directions etc)
thingiverse
free
FPV cover and mount for sony super had fpv cam by swepet
...arts i made for mounting my new fpv camera on my swift2 flying wing. perhaps someone else find it useful or get an idea from it..
Rc
3ddd
$1
RC Helicopter
...rc helicopter
3ddd
вертолет
mini rc helicopter
93.329 polys
3d_export
$7
rc helicopter model
...rc helicopter model
3dexport
rc helicopter model
3d_ocean
$25
RC F1
...rc f1
3docean
auto car control f1 formula race rc remote speed
remote control f1 car
turbosquid
$10
rc plane
...lane
turbosquid
free 3d model rc plane for download as blend on turbosquid: 3d models for games, architecture, videos. (1295828)
turbosquid
$100
RC Helicopter
...free 3d model rc helicopter for download as 3ds, max, and obj on turbosquid: 3d models for games, architecture, videos. (1298511)
turbosquid
$59
Drone with RC
...3d model drone with rc for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1363601)
turbosquid
$75
RC buggy
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$39
RC Plane001
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$30
RC Jet
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$30
Rc airplane
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Tank
archibase_planet
free
Tank
...ibase planet
tank tank-wagon tank-truck tank-car
tank train small n110113 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
3d_ocean
$49
Tank
...tank
3docean
kv-1s tank
tank kv-1s
archibase_planet
free
Tank
...tank
archibase planet
tank medium tank
tank wmcvun n070712 - 3d model (*.3ds) for exterior 3d visualization.
archibase_planet
free
Tank
...k
archibase planet
tank light tank bt-2 high-speed tank
tank bt-2 n200814 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
3d_export
$5
tanks
...tanks
3dexport
tanks
3d_export
free
tank
...tank
3dexport
tank
archibase_planet
free
Tank
...tank
archibase planet
tank heavy tank
tank abrams l n090511 - 3d model (*.3ds) for exterior 3d visualization.
archibase_planet
free
Tank
...tank
archibase planet
tank medium tank
tank m60 n070712 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Tank
...tank
archibase planet
tank medium tank
tank female n070712 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
3d_export
$5
tank
...tank
3dexport
tank lowpoly
Printed
design_connected
$27
...print
designconnected
moroso print computer generated 3d model. designed by wanders, marcel.
3ddd
free
Eichholtz Prints
...- eichholtz print central station i
13 - eichholtz print central station ii
14 - eichholtz print marisa
15 - eichholtz print tish
3ddd
$1
Eichholtz Prints
...print abstract - set of 2
10 - eichholtz print orange abstract
11 - eichholtz print buddha right
12 - eichholtz print buddha left
turbosquid
$1
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
free
Eichholtz Prints
...of 4
2 - print dunbar 2 set of 4
3 - print guadeloupe 1 set of 4
4 - print guadeloupe 2 set of 4
5 - print giles
6 - print trett
3ddd
$1
Eichholtz Prints
...nt tutti frutti
3 - eichholtz prints watson - set of 2
4 - eichholtz prints antique nautilus - set of 2
5 - eichholtz print tiara
3d_export
$5
Monster for printing
...monster for printing
3dexport
monster 3d model printing
3ddd
free
printed rug
...printed rug
3ddd
ковер
very creative printed rug
3ddd
free
Eichholtz Prints
...иал: бумага
габариты (вхш): 72 x 62 см
описание: print sweetmeat - постер в деревянной раме.
3 - prints varsity set of 2
арти
3ddd
free
Art Print Posters
...art print posters
3ddd
прованс
art print posters by patrician prints