Thingiverse
Multispec - LARP Prop
by Thingiverse
Last crawled date: 4 years, 3 months ago
Multispec LARP Prop
Demo Version Here!
Designed as a LARP prop, this is meant to look like a Multispec or scanner thing often found in Sci-Fi films. The inside is hollow and designed to allow enough space for wiring and an arduino, allowing you to wire it up so it does various things. This is a pretty in-depth device and requires a significant amount of electronic components to work as the photos show.
Parts needed:
4 x 35mm M3 Bolts + Nuts
2 x 12mm M2 Bolts + Nuts
Anker 10,000 mah Battery Pack - Model Number: AK-A1263011
4 Digit Seven Segment display. 0.56" Size. TM1637 chip
WS2812B 8bit 5v LED (8 LED Fixed Strip)
2 x WS2812B 1bit 5v LED Breakout (1 LED Fixed board)
10mm LED
2 x GX16 Connector
Smart Rocker Switch
1 x 4 Membrane keypad
128 x 32 I2C oled display
How does it go together?
It's pretty self explanatory how it goes together. 4 Bolts hold the top on whilst the rest should be glued. Nuts sit resessed into the underneath and the bolts shouldn't protude, meaning the should be no sharp edges. The battery handle slides into the groves and should be glued, but there are bolts too just to make it secure.
There's a clip at the bottom to hold the battery in, with an option for a nut and bolt to hold the clip shut (the nut needs to be secured with electrical tape).
IMPORTANT NOTE: This is a work in progress and may be changed in the near future!
What are the files?
Surround: This is the main surround for the main body. Has the holes for the external connectors and the switch
TopCover: Top cover, goes over the top of the Surround and has all the electronics mounted to it
BatteryHolder: This is the handle for the device as well as the battery holder.
BottomCover: VTL branded for your enjoyment. This has a specific orientation relative to the battery holder.
ButtonSurround: Goes round the buttons to prevent them lifting.
Clip: Sits on the bottom of the BatteryHolder and held in place but a bolt.
LED-Cover1: Covers the 8 WS2812b LED strip. Needs to be printed in clear/natural filament.
LED-Cover2: Covers the Single WS2812b LED, 2 of these need to be printed in clear/natural filament.
LED-Cover3: Covers the 10mm LED on the front/Top
Can I sell this?
Afraid Not
Can I buy parts for this?
Full kits for electronics will be coming soon! Along with a construction guide. This is still in development so subject to change.
Demo Version Here!
Designed as a LARP prop, this is meant to look like a Multispec or scanner thing often found in Sci-Fi films. The inside is hollow and designed to allow enough space for wiring and an arduino, allowing you to wire it up so it does various things. This is a pretty in-depth device and requires a significant amount of electronic components to work as the photos show.
Parts needed:
4 x 35mm M3 Bolts + Nuts
2 x 12mm M2 Bolts + Nuts
Anker 10,000 mah Battery Pack - Model Number: AK-A1263011
4 Digit Seven Segment display. 0.56" Size. TM1637 chip
WS2812B 8bit 5v LED (8 LED Fixed Strip)
2 x WS2812B 1bit 5v LED Breakout (1 LED Fixed board)
10mm LED
2 x GX16 Connector
Smart Rocker Switch
1 x 4 Membrane keypad
128 x 32 I2C oled display
How does it go together?
It's pretty self explanatory how it goes together. 4 Bolts hold the top on whilst the rest should be glued. Nuts sit resessed into the underneath and the bolts shouldn't protude, meaning the should be no sharp edges. The battery handle slides into the groves and should be glued, but there are bolts too just to make it secure.
There's a clip at the bottom to hold the battery in, with an option for a nut and bolt to hold the clip shut (the nut needs to be secured with electrical tape).
IMPORTANT NOTE: This is a work in progress and may be changed in the near future!
What are the files?
Surround: This is the main surround for the main body. Has the holes for the external connectors and the switch
TopCover: Top cover, goes over the top of the Surround and has all the electronics mounted to it
BatteryHolder: This is the handle for the device as well as the battery holder.
BottomCover: VTL branded for your enjoyment. This has a specific orientation relative to the battery holder.
ButtonSurround: Goes round the buttons to prevent them lifting.
Clip: Sits on the bottom of the BatteryHolder and held in place but a bolt.
LED-Cover1: Covers the 8 WS2812b LED strip. Needs to be printed in clear/natural filament.
LED-Cover2: Covers the Single WS2812b LED, 2 of these need to be printed in clear/natural filament.
LED-Cover3: Covers the 10mm LED on the front/Top
Can I sell this?
Afraid Not
Can I buy parts for this?
Full kits for electronics will be coming soon! Along with a construction guide. This is still in development so subject to change.
Similar models
thingiverse
free
WS2812B LED Strip Clip / Holder
...strip holders should work on most standard ws2812b or similar led strips that are 10mm wide and 3mm thick....
thingiverse
free
Bicycle Tail Light by markoL1234
...1,7 cm) -lithium battery (18650) -toggle switch mts-102 or similar (mounting hole:6mm) -led strip 5v - 5 leds (76mm...
thingiverse
free
NodeMCU enclosure for WS2812B LED strip by CalmingInfluence
...ed strip can wrap around an included pole for (hopefully) tension relief.
the two pieces screw together with m3 nuts and bolts.
thingiverse
free
LED Strip clip by tdhprestatyn
...p by tdhprestatyn
thingiverse
clip for led strips. 10mm wide and 3.5mm deep. print using translucent pla. holds led strips firm.
thingiverse
free
LED Clip (10mm) for 2020 extrusion. by gl1970
...clips i found were too narrow for my needs. this will hold a 10mm wide strip with some interference (possibly more than needed).
3dwarehouse
free
WS2812B led strip
...ws2812b led strip
3dwarehouse
10mm wide 60pcs/m
thingiverse
free
Led right clip 1.2 by andrewchoi
...ingiverse
small clip to hold a led and batteries. works with 2 x cr2016 batteries or 1 x cr2032 battery. supports multiple leds.
thingiverse
free
Larger LED Strip by CelsoDeSa
...larger led strip by celsodesa
thingiverse
clip for led strip 10mm x 5mm
thingiverse
free
LED Strip Holder with Cable Clips by csprvb
...ith any smd components on the led strip. the whole part is 14mm wide (for a bigger surface area when glueing)
no supports needed.
thingiverse
free
Led Strip Bar Clips by RPiGuy
...oaded another version that added some more clearance tolerances to fit the led strip in easier and made them 1mm instead of .5mm.
Larp
turbosquid
$10
LARP Eye of Doom Shield
... of doom shield for download as 3ds, obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1267837)
turbosquid
$7
Barbarian Spiked Club Larp Weapon
...lub larp weapon for download as 3ds, obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1283621)
thingiverse
free
Burdock Symbol - Jewelry for LARP by kelseycadaver
...burdock symbol - jewelry for larp by kelseycadaver
thingiverse
jewelry piece for my larp character
thingiverse
free
Larp Arrow by r00t86
...ft tennisball (7cm diameter)
split the soft tennisball and glue on the top of the holder.
cut the metal attowhead from the arrow.
thingiverse
free
Larp rings by LeorYamay
...e houses or main religions.
originally i printed the ring portion and the signet portion seperately and heat welded them together
thingiverse
free
LARP Arrow by Kraken907
...50% infill at a 50mm speed. i also use a triangle infill pattern. make sure you do a strength test on each arrow head before use.
thingiverse
free
VtM - LARP tokens by 3DPModder
...ges to use to represent each and landed on a blood drop for blood and a brain to represent will, which i turned into these coins.
free3d
$7
Barbarian Spiked Club Larp Weapon
...dae
-blender scene and node inlcuded
-everythings uv unwrapped
-lowpoly gameready
-texture included
-higher poly version included
thingiverse
free
LARP Chest filler
... can be inserted for players to find.
edit 11/29/2019: added a version with simple legs. this version will probably need supports
thingiverse
free
13th free Company LARP resources by Mokanaman
...13th free company larp resources by mokanaman
thingiverse
the 13th free company warband from swordcraft.
Prop
3ddd
$1
Props
...props
3ddd
props
3d_ocean
$10
Props
...ject you need this props design this 6 taype for props to get your design perfect and nice file include : 1 max 2 obj 3 3ds 4 zip
turbosquid
$15
Props
...s
turbosquid
royalty free 3d model props for download as max on turbosquid: 3d models for games, architecture, videos. (1249032)
turbosquid
$1
PROPS
...d model props for download as unitypackage, obj, fbx, and tga on turbosquid: 3d models for games, architecture, videos. (1627660)
turbosquid
$5
props
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
PROP
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
kids props
...kids props
3ddd
декоративный набор
kids props
3d_ocean
$8
Street props
...l barrier prop roads street street prop
street props game models barrel barrier roads aircos jerrycan models fbx obj and max file
turbosquid
$39
Apocalyptic Props
...uid
royalty free 3d model apocalyptic props for download as on turbosquid: 3d models for games, architecture, videos. (1380028)
turbosquid
$1
Bunker props
...rbosquid
royalty free 3d model bunker props for download as on turbosquid: 3d models for games, architecture, videos. (1196014)