Thingiverse
Multi Use Stand by cfeniak
by Thingiverse
Last crawled date: 3 years ago
A height, angle, and position adjustable stand. Can hold a book, magazine, tablet, drink, or small plate. Extrusion used is 2020 V-Slot. I printed this in PETG.
Needed:
1.6 meters of 2020 V-Slot extrusion
4x 625ZZ bearings
14x M5 T-nuts
14x M5x10mm cap head bolts
2x M5x50mm cap head bolts (for pivoting joints)
2x M5x40mm cap head bolt (for vertical clamp and toothed pivot)
3-5x M5 washers
2 M5 nuts (standard)
2 Printed Nut Holders:http://www.thingiverse.com/thing:641854
ORhttp://www.thingiverse.com/thing:1177235
To build:
1) Print off all parts then clean up any brim or bridged sections. Clean printed holes with a drill if desired
2) Epoxy the two plate pieces together
3) Cut 2020 extrusion. I used to 50cm pieces for the vertical section and two 25-30cm pieces for the base.
4) Assemble the base with 10 M5x10mm bolts and T-nuts
5) Tap the top of the upper vertical piece to an M5 thread or drill it to 4.5mm and force the M5 bolt to cut it's own threads (use a bit of oil).
6) Press fit the bearings into the arms (make sure they go in square or the parts may crack). I used a workbench vise.
7) Press the two M5 nuts into the two printed holders as well.
8) Add the vertical section (see pics). Uses the remaining T-nuts and 10mm bolts plus one long bolt and M5 nut for the clamp.
9) Assemble the top section (see pics). Use 3-4 washers for the middle joint and one for the connection on top of the extrusion.
10) Bolt the assembly to the top of the 2020 extrusion with the tapped hole.
Optional:
To add stability I added some weight to the bottom by bolting on some steel flat bar to the 2020 aluminum. It requires flat bar, T-nuts, and the appropriate length M5 bolts.
Needed:
1.6 meters of 2020 V-Slot extrusion
4x 625ZZ bearings
14x M5 T-nuts
14x M5x10mm cap head bolts
2x M5x50mm cap head bolts (for pivoting joints)
2x M5x40mm cap head bolt (for vertical clamp and toothed pivot)
3-5x M5 washers
2 M5 nuts (standard)
2 Printed Nut Holders:http://www.thingiverse.com/thing:641854
ORhttp://www.thingiverse.com/thing:1177235
To build:
1) Print off all parts then clean up any brim or bridged sections. Clean printed holes with a drill if desired
2) Epoxy the two plate pieces together
3) Cut 2020 extrusion. I used to 50cm pieces for the vertical section and two 25-30cm pieces for the base.
4) Assemble the base with 10 M5x10mm bolts and T-nuts
5) Tap the top of the upper vertical piece to an M5 thread or drill it to 4.5mm and force the M5 bolt to cut it's own threads (use a bit of oil).
6) Press fit the bearings into the arms (make sure they go in square or the parts may crack). I used a workbench vise.
7) Press the two M5 nuts into the two printed holders as well.
8) Add the vertical section (see pics). Uses the remaining T-nuts and 10mm bolts plus one long bolt and M5 nut for the clamp.
9) Assemble the top section (see pics). Use 3-4 washers for the middle joint and one for the connection on top of the extrusion.
10) Bolt the assembly to the top of the 2020 extrusion with the tapped hole.
Optional:
To add stability I added some weight to the bottom by bolting on some steel flat bar to the 2020 aluminum. It requires flat bar, T-nuts, and the appropriate length M5 bolts.
Similar models
thingiverse
free
Bowden Extruder for 2020 Profile - 1.75 MK7 608zz by Enrike_X5
...around 15mm lenth)
1x nema17 stepper
1x ptfe tube
you may need a tap kit (m5 and m8) to correct the threads, and a 2mm drill bit.
thingiverse
free
Belted Extruder v4 bracket for 2020 Extrusion by yesimnathan
...er is built & connected to the bracket, connect the bracket to your 2020 extrusion with the m5x10mm screws & t-slot nuts.
thingiverse
free
Ender5 Plus - Top Front Cross Member Relocator by RedWhere2020
... m5 x 10mm hh bolts
2x m5 x 20mm hh bolts
2x existing m5 hh bolts with washer.
2x existing m5 bh bolts with washer.
works for me.
thingiverse
free
Filler Drop Down for CoreXY with side panels by Phantom329
... frames and 1/8" side panels. for use with filler by hugohuge, print the guide and roller. uses m5x10mm bolts and m5 t-nuts.
thingiverse
free
Dual Extruder by Psycho1981
...ng:
4x allen screw m5
4x square nut m5
4x washer m5
electronic:
-ramps 1.4 board
-atx power supply
-firmware "marlin"
thingiverse
free
Roller by arkeet
... cap screw
2x m5x16 button head cap screw
2x m5 hex nut
2x m5 washer
(the nuts and washers could be replaced with printed parts.)
thingiverse
free
Simple, strong, Bowden Extruder by MortarArt
...2 of m5x12+mm bolts for fixing to 2020 extrusion
2 of m5 washers
2 of m5 t-nuts
2 of m3x12+mm bolts for fixing motor
m3x20mm bolt
thingiverse
free
M5, M4 and M3 nut and washer adaptors for 2020 extrusions. by brunofporto
...washer to interface with the m5 washer.
updates:
modified the m4 version to use a m5 washer for better grip.
added the m3 version
thingiverse
free
Gearbox Hanger for 20mm Extrusions
...o the gearbox before assembling to the extrusion. if done in the opposite order, it will be impossible to place the top m6 screw.
thingiverse
free
Filament spool holder for 2020 extrusion by gregington
...20 extrusion by gregington
thingiverse
spool holder for 2020 extrusion. use m5 8mm bolts with t-nuts to secure to the extrusion.
Cfeniak
thingiverse
free
Corner Shelf by cfeniak
...cfeniak
thingiverse
corner shelf, sectioned into pieces to fit on my 8"x12" bed. printed in pla, attached with epoxy.
thingiverse
free
Tornado Foosball Rod Holder by cfeniak
...tornado foosball rod holder by cfeniak
thingiverse
used for holding rods for practice shots or goalie wars.
thingiverse
free
Rain Diverter Concept by cfeniak
...nspout to divert rain water to rain barrel.
*** this is a concept only, please use model as inspiration for further development
thingiverse
free
ZMR250 Cable Catch by cfeniak
... power and balance charge cables away from the props. 2mm and 3mm version. best printed in something flexible like abs or petg.
thingiverse
free
Multistar Baby Beast Motor Bell Wrench by cfeniak
...multistar baby beast motor bell wrench by cfeniak
thingiverse
makes removing nyloc prop nuts easier
thingiverse
free
Bowden Tube Holder Accessory by cfeniak
...t with two m3 bolts at 10mm spacing. guides the bowden tube. longer one is the one you need to go with the extruder i designed.
thingiverse
free
Shorter 30mm Fan Shroud for Pico Hot End by cfeniak
...shorter 30mm fan shroud for pico hot end by cfeniak
thingiverse
30mm fan shroud for the pico hotend. print in abs.
thingiverse
free
Big Guy Statue Split by cfeniak
... slic3r. exported as individual files. much more printable, but still needs support.
see source references in original version.
thingiverse
free
Stepper motor feed knob by cfeniak
... designed for use with direct drive filament setups for manually feeding filament. push fit. smaller sized knob is big enough.
thingiverse
free
Fluval Flex aquarium lid prop by cfeniak
...niak
thingiverse
simple lid prop i designed to hold up the fluval flex 32.5 gallon / 123 liter tank lid during maintenance, etc.
Multi
3d_export
$5
multi handle
...multi handle
3dexport
multi handle
3d_export
free
Multi socket
...multi socket
3dexport
multi socket
design_connected
$22
Multy Loveseat
...multy loveseat
designconnected
ligne roset multy loveseat 2-seater computer generated 3d model. designed by claude brisson.
turbosquid
$10
multi pan
...
royalty free 3d model multi pan for download as max and ige on turbosquid: 3d models for games, architecture, videos. (1161690)
turbosquid
$9
Multi Plug
...
royalty free 3d model multi plug for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1355953)
turbosquid
$39
Multi Gym
...y free 3d model multi gym for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1275571)
3ddd
free
Ligne Roset Multy
... sofa , мебель
двухместный диван multy от французского производителя ligne roset
3d_export
$5
multi-colored pencils
...multi-colored pencils
3dexport
multi-colored pencils on a mirror surface
3d_export
$5
multi function box
...multi function box
3dexport
it is multi function box in iges format
3ddd
free
ligne roset / MULTY
...ligne roset / multy
3ddd
ligne roset , multy
минималистический диван
Stand
turbosquid
$50
stand watermelon stand
...yalty free 3d model stand watermelon stand for download as ma on turbosquid: 3d models for games, architecture, videos. (1528284)
archibase_planet
free
Stand
...stand
archibase planet
stand post pole
stand - 3d model for interior 3d visualization.
archibase_planet
free
Stand
...stand
archibase planet
stand sport barbell
stand kettler - 3d model for interior 3d visualization.
archibase_planet
free
Stand
...stand
archibase planet
locker drawer stand
stand 897810 - 3d model for interior 3d visualization.
archibase_planet
free
Stand
...stand
archibase planet
stand rack post
stand 2 - 3d model for interior 3d visualization.
archibase_planet
free
Stand
...stand
archibase planet
stand storefront shelving
stand 3 - 3d model for interior 3d visualization.
archibase_planet
free
Stand
...stand
archibase planet
stand shelf shelving
stand 4 - 3d model for interior 3d visualization.
archibase_planet
free
Stand
...stand
archibase planet
stand post stall
stand 5 - 3d model for interior 3d visualization.
archibase_planet
free
Stand
...stand
archibase planet
stand post stall
stand 6 - 3d model for interior 3d visualization.
archibase_planet
free
Stand
...stand
archibase planet
stand post shelving
stand 7 - 3d model for interior 3d visualization.
Use
3ddd
$1
US flag
...us flag
3ddd
флаг
us flag
3d_export
free
Among us
...among us
3dexport
among us red
3d_export
free
Among Us
...character from the game "among us". it can be use as a toy or...
3d_export
$6
among us
...among us
3dexport
doll from among us in red
3d_export
$5
amoung us
...amoung us
3dexport
amoung us character. was created by cinema 4d 19
3d_export
$5
Humvee us
...humvee us
3dexport
humvee us 3d model good quality for animation
3d_export
$15
among us
...among us 3dexport turbosmooth modifier can be use to increase mesh resolution if...
3d_export
$25
mailbox us
...mailbox us
3dexport
low poly model mailbox us. modeling in the blender, texturing in substance painter
design_connected
$13
Use Me
...use me
designconnected
sitland use me computer generated 3d model. designed by paolo scagnellato.
3d_export
$5
Among Us
...rt
the among us model comes in a variety of colors that can be customized by anyone, and even works with little in the animation