Thingiverse
Mod End Caps for Hasbro Spengler Neutrona Wand by Shwalamazula
by Thingiverse
Last crawled date: 4 years, 9 months ago
UPDATE - 22 November 2020
Added a set of new caps for Aux Jack mods. There is a flat cap with Aux Jack. Additionally, there are caps with the 3/4" stub with just the jack, the jack + 2 circuit holes, and the jack + 4 circuit holes. There are also a pair of files with the suffix SB. These 2 files have sacrificial bridges over the holes in the cap. This will help by allowing you to print with less support. All you have to do is use a hobby knife or something to punch thru the bridge. It is only .2 mm thick (1 layer). Updated the AllCaps.7z archive to include the new files.
UPDATE - 25 October 2020
Added a passthru cap that has the inner nub that presses against the battery pack removed. Updated the AllCaps.7z archive to include the new files
UPDATE - 15 October 2020
Re-named the files to match my submission on the PrusaPrinters page to keep consistency and make it easier to figure out which models go with which files. I also added a single "AllCaps.7z" file to make downloading the entire set easier.
UPDATE - 15 October 2020
Added caps with GX-20 geometry.
Threaded handle endcap for 2020 Hasbro Spengler Neutrona Wand.
I knew I was going to need a spare sometime or that I would be needing to modify one for wire passthrough for modding. There is a tight-thread version of all the models for those wanting a tighter fit or using a resin printer.
Caps
Flat Cap
Flat Cap with GB Logo
Cap with 3/4" Loom Stub
Cap with 3/4" Loom Stub and Circuit Passthrough
Cap with GX-20 Geometry
Cap with 3/4" Loom Stub and Circuit Passthrough without Battery Nub
Cap with 3/4" Loom Stub and Aux Jack
Cap with 3/4" Loom Stub and Aux Jack and 2-Port Circuit Passthrough
Cap with 3/4" Loom Stub and Aux Jack and 4-Port Circuit Passthrough
Added a set of new caps for Aux Jack mods. There is a flat cap with Aux Jack. Additionally, there are caps with the 3/4" stub with just the jack, the jack + 2 circuit holes, and the jack + 4 circuit holes. There are also a pair of files with the suffix SB. These 2 files have sacrificial bridges over the holes in the cap. This will help by allowing you to print with less support. All you have to do is use a hobby knife or something to punch thru the bridge. It is only .2 mm thick (1 layer). Updated the AllCaps.7z archive to include the new files.
UPDATE - 25 October 2020
Added a passthru cap that has the inner nub that presses against the battery pack removed. Updated the AllCaps.7z archive to include the new files
UPDATE - 15 October 2020
Re-named the files to match my submission on the PrusaPrinters page to keep consistency and make it easier to figure out which models go with which files. I also added a single "AllCaps.7z" file to make downloading the entire set easier.
UPDATE - 15 October 2020
Added caps with GX-20 geometry.
Threaded handle endcap for 2020 Hasbro Spengler Neutrona Wand.
I knew I was going to need a spare sometime or that I would be needing to modify one for wire passthrough for modding. There is a tight-thread version of all the models for those wanting a tighter fit or using a resin printer.
Caps
Flat Cap
Flat Cap with GB Logo
Cap with 3/4" Loom Stub
Cap with 3/4" Loom Stub and Circuit Passthrough
Cap with GX-20 Geometry
Cap with 3/4" Loom Stub and Circuit Passthrough without Battery Nub
Cap with 3/4" Loom Stub and Aux Jack
Cap with 3/4" Loom Stub and Aux Jack and 2-Port Circuit Passthrough
Cap with 3/4" Loom Stub and Aux Jack and 4-Port Circuit Passthrough