Thingiverse
MiSTer - Case Universal v1.2 - Updated by NegSol
by Thingiverse
Last crawled date: 4 years, 5 months ago
MiSTer - Case Universal v1.2 Updated
Update - 21.05.2019
Added MiSTer Case Uni v1.2 Bottom Shell_Fix1.stl - More clearance for the SD Memory Card Connector on the underside of the DE10.
Update 2018-01-05
I added two new Top Shells now including buttons, the vents of the v5.2 case and an optional fan holding cage. The cage was matched for the noctua 40x40x20 mm fan but it should work well with other fans of similar dimensions. The noctua fan fits without glue or screwing requirements. Other fans might need to be glued in place.
The buttons are matched for the old 2.7 version of the I/O-Bord. Compared to the v5.2 these buttons are very much at the edge of the case. I did my best to accommodate the same buttons used in the universal case for the v5.2 I/O-Board. The buttons had to move quite a bit but ultimately feel even a little nicer and "clickier" compared to the other cases.
Everything should print in PLA in place without supports - layer height was again 0.18 mm.
I hope some guys still using the v2.7 I/O-Board will enjoy the new Top Shells. Your feedback is welcome as always.
The new parts are:
MiSTer Case Uni v2 Top Shell_Buttons.stl
MiSTer Case Uni v2 Top Shell_Buttons_Fan.stl
Update 2017-12-26
Added a new Top similar to the v5.2 of the case incl the new vents on the top shell.
You will have to provide your on fan bracket solution for now - until I come up with something. Object: MiSTer Case Uni v1 Top Shell_New_Vents.stl
Original Summary
I remixed the Universal Case for the MiSTer to now support the I/O-Board 2.7 .
Also I increased the distance between bottom and the pbc to allow for more air flow. Only the top shell of the case remains unchanged and can be used with this version 1.2.
The original screws of the DE10 Nano can now be used to fix the DE10 Nano inside the case (see pictures). If you find this to be too difficult try using sharp screws to prepare the holes. It works!
For the MiSTer logo sign please look at the remix section or at the original MiSTer 1.0 case.
Enjoy.
https://github.com/MiSTer-devel/Main_MiSTer/wiki
http://www.atari-forum.com/viewtopic.php?f=117&t=32067
Update - 21.05.2019
Added MiSTer Case Uni v1.2 Bottom Shell_Fix1.stl - More clearance for the SD Memory Card Connector on the underside of the DE10.
Update 2018-01-05
I added two new Top Shells now including buttons, the vents of the v5.2 case and an optional fan holding cage. The cage was matched for the noctua 40x40x20 mm fan but it should work well with other fans of similar dimensions. The noctua fan fits without glue or screwing requirements. Other fans might need to be glued in place.
The buttons are matched for the old 2.7 version of the I/O-Bord. Compared to the v5.2 these buttons are very much at the edge of the case. I did my best to accommodate the same buttons used in the universal case for the v5.2 I/O-Board. The buttons had to move quite a bit but ultimately feel even a little nicer and "clickier" compared to the other cases.
Everything should print in PLA in place without supports - layer height was again 0.18 mm.
I hope some guys still using the v2.7 I/O-Board will enjoy the new Top Shells. Your feedback is welcome as always.
The new parts are:
MiSTer Case Uni v2 Top Shell_Buttons.stl
MiSTer Case Uni v2 Top Shell_Buttons_Fan.stl
Update 2017-12-26
Added a new Top similar to the v5.2 of the case incl the new vents on the top shell.
You will have to provide your on fan bracket solution for now - until I come up with something. Object: MiSTer Case Uni v1 Top Shell_New_Vents.stl
Original Summary
I remixed the Universal Case for the MiSTer to now support the I/O-Board 2.7 .
Also I increased the distance between bottom and the pbc to allow for more air flow. Only the top shell of the case remains unchanged and can be used with this version 1.2.
The original screws of the DE10 Nano can now be used to fix the DE10 Nano inside the case (see pictures). If you find this to be too difficult try using sharp screws to prepare the holes. It works!
For the MiSTer logo sign please look at the remix section or at the original MiSTer 1.0 case.
Enjoy.
https://github.com/MiSTer-devel/Main_MiSTer/wiki
http://www.atari-forum.com/viewtopic.php?f=117&t=32067