Thingiverse
Marble ball release mechanism cylinder version by DotNetWorker
by Thingiverse
Last crawled date: 3 years ago
Danger of finger injuryThe servo is not strong enough to cause a serious injury (I don't think), but especially for very young children with small fingers it may nip them, so It is recommended to glue tube as least longer than a finger to each entrance of the device to prevent accidents with fingers being poked into the device while in operation.
Marble release mechanism 2
Revisit of marble release problem, my previous "beam engine" style device that was not reliable enough at delivering a single ball every time.
This is a very reliable mechanism allowing only one 21mm diameter ball to drop at a time, it does not fail!
Instructions:
Attach a SG90 micro servo. Use M2.5 nut and bolt to mount the servo to the mounting points. See photographs for guide.
Mount the round hub gear to the servo horn, cutting off the tips so they do not foul the meshing of the gear teeth.
The cylinder rotates through 120 degrees to release the ball from a 30 degree feed tube (25mm electrical conduit) to a vertical drop out the bottom. 25mm electrical conduit should friction fit into the holes.
Use the washer superglued to the shaft (only) to keep the cylinder in place. It should be glued hard against the face so there is no lateral movement, or the gears my loose mesh. The open cone side of the washer should be placed against the face as it has less surface area (less friction) and also the gap between shaft and washer should help prevent the super glue getting onto the face and gluing the shaft it in position. Keep moving the shaft while drying to ensure it does not get stuck.
The square of the other gear cog should push onto the cylinder with a firm friction fit. Glue if required for extra security.
If a clean print has been made, then the cylinder should move very smoothly and freely in its position before the motor is attached.
Before screwing on the servo horn, thus meshing the gears, find the mid position of the servo and set this to be the mid position of the cylinder movement, so that when manually moving the servo it covers the range needed to release the ball.
Enjoy and do please comment and post photos if you make this, as it motivates me to post more!https://youtu.be/5PLN1OL_mF0https://youtu.be/kqvsuGK7beohttps://youtu.be/cNvKvMjKVTQhttps://youtu.be/tcLlVTGSCCc
UPDATED 2018-03-10
Changed spur gears to 40 from 48 tooth for ease of printing.
Marble release mechanism 2
Revisit of marble release problem, my previous "beam engine" style device that was not reliable enough at delivering a single ball every time.
This is a very reliable mechanism allowing only one 21mm diameter ball to drop at a time, it does not fail!
Instructions:
Attach a SG90 micro servo. Use M2.5 nut and bolt to mount the servo to the mounting points. See photographs for guide.
Mount the round hub gear to the servo horn, cutting off the tips so they do not foul the meshing of the gear teeth.
The cylinder rotates through 120 degrees to release the ball from a 30 degree feed tube (25mm electrical conduit) to a vertical drop out the bottom. 25mm electrical conduit should friction fit into the holes.
Use the washer superglued to the shaft (only) to keep the cylinder in place. It should be glued hard against the face so there is no lateral movement, or the gears my loose mesh. The open cone side of the washer should be placed against the face as it has less surface area (less friction) and also the gap between shaft and washer should help prevent the super glue getting onto the face and gluing the shaft it in position. Keep moving the shaft while drying to ensure it does not get stuck.
The square of the other gear cog should push onto the cylinder with a firm friction fit. Glue if required for extra security.
If a clean print has been made, then the cylinder should move very smoothly and freely in its position before the motor is attached.
Before screwing on the servo horn, thus meshing the gears, find the mid position of the servo and set this to be the mid position of the cylinder movement, so that when manually moving the servo it covers the range needed to release the ball.
Enjoy and do please comment and post photos if you make this, as it motivates me to post more!https://youtu.be/5PLN1OL_mF0https://youtu.be/kqvsuGK7beohttps://youtu.be/cNvKvMjKVTQhttps://youtu.be/tcLlVTGSCCc
UPDATED 2018-03-10
Changed spur gears to 40 from 48 tooth for ease of printing.
Similar models
thingiverse
free
Marble ball release mechanism by DotNetWorker
... works when on a gentle angle. too much tilt will force more than one ball through at a time. play with the timings on the servo.
grabcad
free
Ball Bearing
...ball bearing
grabcad
use in mechanical device for resting and friction free for rotate shaft etc.
grabcad
free
Payload dropping mechanism
...nts: a servo motor and a release mechanism. the servo motor is used to move the release mechanism, which then releases the cargo.
grabcad
free
Three-finger friction gripper
...three-finger friction gripper
grabcad
three-finger friction gripper
it employs mg995 type servo and 8x304mm ball bearings
thingiverse
free
Turnigy TG-1800 Pan servo horn support by omegooliebird
... glued directly to the servo horn without the glue going through the holes in the horn and bonding it to the actual servo itself.
grabcad
free
Servo horn 25mm
...servo horn 25mm
grabcad
metal servo horn 25mm long
thingiverse
free
Elfdroid Eye Mechanism by aneta82016
...output shaft. i used a dab of gorilla glue to hold it in place. this prevents the eyeballs coming loose after repeated movements.
thingiverse
free
Hotshot Servo Combo by Qbee
...essing needed on the washer as the fit is very tight. any printing edges - especially of the first layer - will block the washer.
thingiverse
free
"Geared" Servo Horn Arm Assortment - for MG90s / SG90s Servo by crashworks3d
...m) - length
servo horn arm geared (60mm) - length
servo horn arm geared (64mm) - length
servo horn arm geared (70mm) - length
thingiverse
free
Servo Horn Extension by MateusOP
... i did not designed the servo attachment, you gave to glue it into an original servo horn. this is the way i needed to create it.
Dotnetworker
thingiverse
free
Sound detector board case by DotNetWorker
...sound detector board case by dotnetworker
thingiverse
case for audio detection board
allows access to trigger level
thingiverse
free
Eachine VTX03 Super Mini case by DotNetWorker
...eachine vtx03 super mini case by dotnetworker
thingiverse
simple holder to protect the eachine vtx03 super mini.
thingiverse
free
Handle for workbench (not workmate) by DotNetWorker
... my cheap workmate like workbench handle after jigsawing through the original one.
it needs a strong push to click it into place.
thingiverse
free
Coffee scoop measure by DotNetWorker
...d one up.
coffee scoop will fit diagonally on most printer beds.
it has a long handle for getting to the bottom of coffee bag.
thingiverse
free
MCP23017 Slip Case for port expander by DotNetWorker
...cp23017 16 bit port expander
m3 screw holes go all way through for mounting or optional model with lugs for screwing to surfaces.
thingiverse
free
Cycle pump cap replacement (Beto) by DotNetWorker
...e with beto hand pump.
thread is really fine so used a 0.2mm nozzle.
no supports required.
use more than 30% infill for strength.
thingiverse
free
Whiteboard Pen Holder for T slot whiteboards by DotNetWorker
...n in one of the photographs).
the pen holder slides into the t slot and can be positioned anywhere along the bottom of the board.
thingiverse
free
LED Matrix round eye holders by DotNetWorker
...learn.adafruit.com/animating-multiple-led-backpacks/ideas
when printed the matrix does push in but is a friction fit (its tight).
thingiverse
free
E23A 12V Battery holder by DotNetWorker
...tery held in holder, so provided a hole in back to allow the use of a pen or similar to push the battery out of the holder again.
thingiverse
free
REWIRE 102 Nano GPS Tracker battery protector by DotNetWorker
...inserting this 3d printed part, around the battery connector it takes the force of such an incident, thus protecting the battery.
Marble
3d_export
free
marbles
...marbles
3dexport
animated marbles
3ddd
$1
Marble
...marble
3ddd
мрамор
marbles of turkey
3d_export
free
marbles
...marbles
3dexport
3d_export
$5
Marble vase
...marble vase
3dexport
marble vase
turbosquid
$2
Marble
...quid
royalty free 3d model marble for download as ma and max on turbosquid: 3d models for games, architecture, videos. (1240771)
turbosquid
$2
marble
...d
royalty free 3d model marble for download as blend and fbx on turbosquid: 3d models for games, architecture, videos. (1645970)
3d_export
$5
marble skirting
...marble skirting
3dexport
marble skirting for indoor design.
3ddd
$1
Marble Table
...marble table
3ddd
журнальный , круглый
marble table
turbosquid
$10
Marbles
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Marble lamp
...marble lamp
3ddd
marble lamp in style of 30's
Release
turbosquid
$39
Sofa. Updated release
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
shift lock release kia soul
...shift lock release kia soul
3dexport
shift lock release kia soul
turbosquid
$14
Quick release swivel carabiner with ring
...ease swivel carabiner with ring for download as sldpr and stl on turbosquid: 3d models for games, architecture, videos. (1668426)
turbosquid
$60
AUTOMATIC AIR RELEASE VALVE GRP33-07
...odel automatic air release valve grp33-07 for download as ipt on turbosquid: 3d models for games, architecture, videos. (1404884)
3d_export
$10
Kitchen Release Mat
...xture format: .png .jpg<br>resolution: 1024*1024<br>pbr in substance painter<br>formats: .obj .gltf .fbx .blend
3d_export
$5
logitech g27-g29 quick release
...r and the other wheel adaptor.<br>files are in stl format, but if you want to edit parts i give you files in sldprt format.
3d_export
$20
mutante veneno
...model created in zbrush 33cm ready for printing, previously release in 6...
3d_export
$5
Drowned Plush Minecraft
...for microsoft windows, macos and linux, and was later re-release for a wide variety of platforms. it is the...
3d_export
$7
Toy drone for kids
...drone for kids. based on only 3 d models. release for toy...
3d_export
$5
futuristic car
...3dexport a futuristic car made in anticipation of the release of cyberpunk 2077 and based on elon musk's...
Cylinder
turbosquid
$1
Piston - Cylinder Cylinder Engine
...nder cylinder engine for download as ige, obj, stl, and sldpr on turbosquid: 3d models for games, architecture, videos. (1235278)
3ddd
$1
sofa cylinder
...sofa cylinder
3ddd
круглый
sofa cylinder
turbosquid
$1
Cylinder Head - Single Cylinder Engine
...ngle cylinder engine for download as ige, obj, stl, and sldpr on turbosquid: 3d models for games, architecture, videos. (1222618)
turbosquid
$10
Cylinder
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$120
Four cylinder
...four cylinder
3dexport
four cylinder render 3d modelling
3d_export
$5
piston cylinder
...piston cylinder
3dexport
piston cylinder arrangement sketched in solidworks
3ddd
$1
Cylinder Lamp A
...cylinder lamp a
3ddd
cylinder form lamp for loft interior
archive3d
free
Cylinder 3D Model
... model
archive3d
cylinder drum
cylinder - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archive3d
free
Cylinder 3D Model
...odel
archive3d
drum cylinder
cylinder 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
free
Gas Cylinder
...er
turbosquid
free 3d model gas cylinder for download as fbx on turbosquid: 3d models for games, architecture, videos. (1419990)
Ball
turbosquid
$5
Ball on a Ball
...uid
royalty free 3d model ball on a ball for download as obj on turbosquid: 3d models for games, architecture, videos. (1484719)
archibase_planet
free
Ball
...ball
archibase planet
ball golf ball
ball - 3d model (*.gsm+*.3ds) for 3d visualization.
3d_export
$5
ball
...ball
3dexport
ball
archibase_planet
free
Ball
...ball
archibase planet
ball football soccer ball
ball n100714 - 3d model (*.gsm+*.3ds+*.max) for exterior 3d visualization.
3d_export
$5
ball
...ball
3dexport
soccer ball
archibase_planet
free
Ball
...ball
archibase planet
ball football
ball n100914 - 3d model (*.gsm+*.3ds+*.max) for 3d visualization.
3d_ocean
$5
Snooker Balls
... set balls snooker snooker balls white ball yellow ball
set snooker balls format include : .c4d .3ds .obj build in cinema 4d r13
3d_export
free
ball
...ball
3dexport
this is 3d model ball's
3d_ocean
$2
Soccer Ball
...soccer ball
3docean
ball red and yellow ball red ball soccer ball
a gorgeous red and yellow seamless soccer ball
3d_ocean
$5
Billard Balls
...low poly billiard balls. numbering from 1 to 15 plus the cue ball. each of the balls excluding the cue ball has a 4k texture map.
Mechanism
3d_export
$50
Mechanism
...mechanism
3dexport
mechanism -------- animation is present only in the blender file.
3d_export
$5
mechanics
...mechanics
3dexport
turbosquid
$50
mechanic
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Mechanical Wasp
...mechanical wasp
3ddd
робот
mechanical wasp
3d_export
$20
Mechanical tail
...mechanical tail
3dexport
mechanical tail<br>four-part movement
3d_export
$5
mechanical ballista
...mechanical ballista
3dexport
a mechanical ballista useful for medieval or fantasy games does not contain animations
turbosquid
$50
Mechanical Spider
...royalty free 3d model mechanical spider for download as blend on turbosquid: 3d models for games, architecture, videos. (1599864)
turbosquid
$35
Mechanical fish
...id
royalty free 3d model mechanical fish for download as max on turbosquid: 3d models for games, architecture, videos. (1152530)
turbosquid
$27
Step Mechanism
...uid
royalty free 3d model step mechanism for download as obj on turbosquid: 3d models for games, architecture, videos. (1436024)
turbosquid
$15
Mechanical head
...id
royalty free 3d model mechanical head for download as max on turbosquid: 3d models for games, architecture, videos. (1164676)
Version
3ddd
$1
Diamond version
...nd , version , ванна
visionnaire - diamond bath
turbosquid
$50
LibraryMini Version
...free 3d model librarymini version for download as max and jpg on turbosquid: 3d models for games, architecture, videos. (1617724)
design_connected
$34
Barocco Version 01
...barocco version 01
designconnected
zanotta barocco version 01 computer generated 3d model. designed by progetti, emaf.
design_connected
$27
Barocco Version 02
...barocco version 02
designconnected
zanotta barocco version 02 computer generated 3d model. designed by progetti, emaf.
turbosquid
free
Door [2 versions]
...rbosquid
free 3d model door [2 versions] for download as fbx on turbosquid: 3d models for games, architecture, videos. (1223985)
turbosquid
$2
seat version 0.1
...
royalty free 3d model seat version 0.1 for download as blend on turbosquid: 3d models for games, architecture, videos. (1432653)
3d_export
$10
magnolia grandiflora mature version
...magnolia grandiflora mature version
3dexport
magnolia grandiflora mature version
3d_export
$8
room assets and voxel version
...room assets and voxel version
3dexport
room assets and voxel version
turbosquid
$35
Zil Civilian version
... model zil civilian version for download as cgf, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1639420)
turbosquid
$3
Chair 3 versions
...3d model chair 3 versions for download as blend, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1657530)