GrabCAD
Lunar TuniSampler
by GrabCAD
Last crawled date: 1 year, 11 months ago
In order to fulfill the purpose of sampling the lunar regolith layer by layer into a container, I came with a relatively simple design to separate and sequential rearrange the collected materials.
The "Lunar TuniSampler" weighs 494grams, made of aluminum and Teflon, it will be attached to a six bolts set-up, three on each side of the housing part.
The whole automated system will be in a sleep mode unless the Funnel receives material being detected by means of the Occupancy sensor that will engage the DC motor to rotate the Spiral PTFE(teflon) brush, and consequently will facilitate the filtration process all the way-out. All of the material will slide above a specific sized mesh, the first stage mesh will filtrate less than 3 mm of diameter material, the second stage will do so but with a maximum of 20 mm of diameter, the non infiltrated material will be evacuated and and thrown away thru the opened ending.
The filtrated rocks are collected and locked in the Sampling chamber, after 60 seconds of filtration, the on-board computer will send an order to stop the motor and activate the Micro Linear actuator (1) to release the fine regolith to fill the first layer into the container passing through the sampling duct, then the Micro Linear actuator (2) is being already activated and the second deposit successfully filled.
All the cycle will continue processing until the container is full, being detected by the means of an IR Camera and went in sleep mode to save power unless the container emptied.
It will be necessary the presence of a micro controller or a nano computer(Raspberry like) on the (lander/Rover) and linkage cables with the main camera and sensors embedded in the Lunar TuniSampler to process the described task.
Best regards
#MWS_concepts
The "Lunar TuniSampler" weighs 494grams, made of aluminum and Teflon, it will be attached to a six bolts set-up, three on each side of the housing part.
The whole automated system will be in a sleep mode unless the Funnel receives material being detected by means of the Occupancy sensor that will engage the DC motor to rotate the Spiral PTFE(teflon) brush, and consequently will facilitate the filtration process all the way-out. All of the material will slide above a specific sized mesh, the first stage mesh will filtrate less than 3 mm of diameter material, the second stage will do so but with a maximum of 20 mm of diameter, the non infiltrated material will be evacuated and and thrown away thru the opened ending.
The filtrated rocks are collected and locked in the Sampling chamber, after 60 seconds of filtration, the on-board computer will send an order to stop the motor and activate the Micro Linear actuator (1) to release the fine regolith to fill the first layer into the container passing through the sampling duct, then the Micro Linear actuator (2) is being already activated and the second deposit successfully filled.
All the cycle will continue processing until the container is full, being detected by the means of an IR Camera and went in sleep mode to save power unless the container emptied.
It will be necessary the presence of a micro controller or a nano computer(Raspberry like) on the (lander/Rover) and linkage cables with the main camera and sensors embedded in the Lunar TuniSampler to process the described task.
Best regards
#MWS_concepts
Similar models
grabcad
free
FilterTunsi
...rover) and linkage cables with the main camera and sensors embedded in the "filtertunsi" to process the described task.
grabcad
free
NASA LUNAR REGOLITH SAMPLING ROBOT
...nasa lunar regolith sampling robot
grabcad
low mass and low power lunar regolith sampling robot with bldc motor drive
grabcad
free
NASA Lunar Sampling Tool
...ection, discarding unwanted regolith!
this design was created and rendered in ptc creo 4.0.
thank you for considering my design!
grabcad
free
Lunar Sample Extracter with Rotating Filter
...needed.
total consumption=20watt
13 watt filtering micromotor
7 watt lead screw servomotor with gearbox
total weight: 480 grams
grabcad
free
[REGOLITH REAPER] NASA Lunar Sampling System
...nsor reports that it is full.
optical regolith level sensors are based on ir proximity sensors.
best regards,
andrzej laczewski
grabcad
free
NASA Lunar Sampling System
...nasa lunar sampling system
grabcad
sample separation system is capable to collect, separate and layer regolith.
grabcad
free
Roving Lunar Sampling System (RLSS)
...
more details in readme-rlss.pdf
design by aurelian z. https://grabcad.com/aurelian.z
and diana p. https://grabcad.com/diana-67
grabcad
free
LBWC
...d outside of sampling system. the linear ball screw system deposit the material into fine and 20 mm layer as per the requirement.
grabcad
free
lunar sample collector
...tion of outer driver fill regolith another rotation fill rock.by rotating servo motor less than 1 cm material can be filled
grabcad
free
Regolith Lunar Sampler Sorter (RLSS)
...tion to assist movement of material.
*sorted material can be viewed through a slot in the top of the feed chute prior to deposit.
Lunar
grabcad
free
lunar vehicle
...lunar vehicle
grabcad
lunar vehicle
grabcad
free
lunar heliostat
...lunar heliostat
grabcad
lunar heliostat
grabcad
free
Lunar gantry
...lunar gantry
grabcad
lightweight lunar gantry
grabcad
free
Lunar Torch
...lunar torch
grabcad
lunar torch rover model
grabcad
free
NASA LUNAR
...nasa lunar
grabcad
design for the nasa lunar sampling challenge
grabcad
free
lunar lander
...lunar lander
grabcad
lunar lander for e-fest competition.
grabcad
free
Lunar SpiderGantry
...ept for a lunar unloading module that is able to land on the lunar surface itself and perform the task without human intervention
grabcad
free
Portico lunar
...portico lunar
grabcad
portico lunar feito para o desafio
grabcad
free
NURUS - Lunar Masa
...nurus - lunar masa
grabcad
lunar masa
grabcad
free
Lunar Rover
...lunar rover
grabcad
apollo lunar rover
collapsible transportation used on apollo 15-17
4 wheel drive