Thingiverse
LulzBot TAZ 6 Remix Custom by ant0ny
by Thingiverse
Last crawled date: 3 years ago
This has been totally updated into a new version of the Yaxis and other improvements https://www.thingiverse.com/thing:3819363
If you prefer this Yaxis with the supported rails... just download the updated parts from the new version.
This is my version of the LuzBot TAZ 6. Based on and partly redrawn from the LulzBot Opensource files but reconfigured to get away from some of the unusual ideas like not proper belt tensioning and the badly drawn components which errors left me baffled.
2018 July: Added 10mm Bearing holders for the X axis carriage.
2018 MAJOR UPDATE:
I have redrawn the lower Z axis motor mounts (version 3). This a more printer friendly and gives a little more Z axis height for certain setups (depends on motor length)
X motor and idler mounts Version 3 (yes called Z still)
Motor End has blind holes so no melt-in thread needed.
Idler End beefed up around the tensioner.
New Corner bracket for the top left rear... gives the Z axis a little more height.
New Case for MKS Gen 1.4 with 60 or 80mm fans and outside reset button.
New 24v Power supply Brackets 115mm hole center (print 2)
new 24v PSU Wire cover and Power socket/switch 3Pin IEC320 C14
To do:
A totally new Y axis has been drawn up and I have been using it for a few months. I just have a few tweaks and I will put it up. This is a OpenBuilds style with 12mm Supported Rail... easier to print and assemble.
Complete Cable Management system... drawn and tested just need to check files and upload.
This whole page needs a rewrite and move older files into ZIp files to make it less confusing but still accessible for anyone wanting them.
--
The Yaxis is actually a protoype for testing if the cheap chinese supported rail mixed with printed parts where a viable idea... so far it looks like a success. Infact the whole build is a test to see if it was scale-able to a 500x500x500mm print volume... definitely could be possible but again just spend a few hundred more and go full Openbuilds.
The Yaxis is on 12mm Supported Liner Rails with belt tensioner. The pics show the 200x300mm bed plate. I am currently waiting for my designed ali bed to be cut for 24v 300x300mm BigBed from reprap.me.
Added pics of the 300x300 bed as if it was in place (waiting for the plate to be cut) You can see it is on the edge of the plate at X0 endstop and about 5-8mm past at full X travel So to answer Q about that it is ok with the cutting list of the frame. You could of course give yourself more room by cutting the 2020 parts longer and the X smoothrods.
Z axis uses 10mm smooth rod and 10x2 leadscrew with 608Z bearing at bottom only but has provision for top bearing.
X axis is quite modified from the LulzBot. Added X axis belt tension similar to the rest of mainstream printers.
Extruder setup is Titan and E3dV6 with 3DTouch auto bed leveling (BLTouch will fit)
One feature I wanted to test was the M3 insert threads. This was something I hadn't tried before and although some of them a used in a manner that would not be mechanically sound actually sort of worked pretty good.. e.g the 12mm X axis shafts held in place by this method means that that the force needed to retain the shaft but not pull the insert from the part is just almost there. the grip where I couldn't pull the shaft through the hole was at the point the grub screw started to deform the part and push the hole away from the shaft.
I bought these from (Australia) Cross Tools PHONE 1800 025 500
http://www.crosstools.com.au/threaded-inserts-for-plastic%2c-wood%2c-injection---rotomolding.html#insertsforplastic
Part: TH-M30-SV
For those not wanting to use inserts for a Beer I could change this to a way easier system that the LulzBot guys could have implemented lol.
Update: in the downloads there is a ZIP file 1st_concept_z_carriage_no_insert.zip which contains the STL's for doing the X Smooth Rods without using the Melt in inserts. These are not tested to date but should work without a problem.
It uses M3 Square nuts... square because at 3mm a hexagon is almost round and it might just spin. So do a search on ebay and get some square nuts they are cheap.
Note: the left hand one has a shouldered hole so you only need nuts at one end... this could also be used for the Heat Insert instead of the z_carriage_motor_ak.stl and save 2 inserts for a rainy day.
Added: Y_axis_linear_rail_clamp_less_2mm.stl with 2mm more clearance for the Y axis bearing block.
Added: Y_axis_endplate_Test.stl this is to make sure the endplates fit the Linear Rails
Added: LulzBot X Carriage_hole_Centers.dxf Showing placement of extruder holes (23mm pitch)
With this cutting list the Max Travel of Z is 250mm. You can achieve 260mm but homing with the raise before descending will catch the fame corner on the X motor.
Parts:
2020 extrusion
4x 500
4x 510
SBR12 12mm Supported Linear Rail (Y axis)
2x 500
SBR12UU Bearing Block (Y axis)
4x bearing block (or three if preferred)
12mm Smoothrod (X axis)
2x 520
10mm Smoothrod (Z axis)
2x 450
10x2 Leadscrew
2x 420
Z X Axis Bearing
Z 2x LM10LUU (long bearing or 4x short)
X 3x LM12UU
Z axis Leadscrew 2x 608Z bearing
T-Slot Slide in T-nuts for 2020 Frame
M5 T nuts x80+ (76 for frame and Y axis only)
Bolts
M5x10 Caphead x80+ (76 for frame and Y axis only)
M5x25 Caphead x11 Yaxis to Main Frame and XY belt pulley +Nyloc nuts
M4x30 Caphead x3 XY Belt tension +Nyloc nuts
M4x20 x8 Mixture of Caphead and Countersunk for X carriage bearings +Nyloc nuts
M3x55 Caphead x8 Yaxis Clamp Blocks +Nyloc nuts
M3x10 Caphead x20 Nema17 motor mount and Zaxis M10x2 nut
GT2 Belt
X aprox 900mm
Y aprox 1000mm
GT2 Pulley
Motor 2x 20 Tooth 5mm shaft (or your motor shaft)
Idler 2x 20 (tooth or not) 5mm
Y AXIS and 200x300 Bed Option:
These files are in a zip file to keep them separate.
I have added the parts needed to use the more STD Y axis you see using 10mm Smooth Rods instead of Supported Linear rails. This is the Wilson II system which not a bed system but has multiple parts to make the bed.
If you prefer this Yaxis with the supported rails... just download the updated parts from the new version.
This is my version of the LuzBot TAZ 6. Based on and partly redrawn from the LulzBot Opensource files but reconfigured to get away from some of the unusual ideas like not proper belt tensioning and the badly drawn components which errors left me baffled.
2018 July: Added 10mm Bearing holders for the X axis carriage.
2018 MAJOR UPDATE:
I have redrawn the lower Z axis motor mounts (version 3). This a more printer friendly and gives a little more Z axis height for certain setups (depends on motor length)
X motor and idler mounts Version 3 (yes called Z still)
Motor End has blind holes so no melt-in thread needed.
Idler End beefed up around the tensioner.
New Corner bracket for the top left rear... gives the Z axis a little more height.
New Case for MKS Gen 1.4 with 60 or 80mm fans and outside reset button.
New 24v Power supply Brackets 115mm hole center (print 2)
new 24v PSU Wire cover and Power socket/switch 3Pin IEC320 C14
To do:
A totally new Y axis has been drawn up and I have been using it for a few months. I just have a few tweaks and I will put it up. This is a OpenBuilds style with 12mm Supported Rail... easier to print and assemble.
Complete Cable Management system... drawn and tested just need to check files and upload.
This whole page needs a rewrite and move older files into ZIp files to make it less confusing but still accessible for anyone wanting them.
--
The Yaxis is actually a protoype for testing if the cheap chinese supported rail mixed with printed parts where a viable idea... so far it looks like a success. Infact the whole build is a test to see if it was scale-able to a 500x500x500mm print volume... definitely could be possible but again just spend a few hundred more and go full Openbuilds.
The Yaxis is on 12mm Supported Liner Rails with belt tensioner. The pics show the 200x300mm bed plate. I am currently waiting for my designed ali bed to be cut for 24v 300x300mm BigBed from reprap.me.
Added pics of the 300x300 bed as if it was in place (waiting for the plate to be cut) You can see it is on the edge of the plate at X0 endstop and about 5-8mm past at full X travel So to answer Q about that it is ok with the cutting list of the frame. You could of course give yourself more room by cutting the 2020 parts longer and the X smoothrods.
Z axis uses 10mm smooth rod and 10x2 leadscrew with 608Z bearing at bottom only but has provision for top bearing.
X axis is quite modified from the LulzBot. Added X axis belt tension similar to the rest of mainstream printers.
Extruder setup is Titan and E3dV6 with 3DTouch auto bed leveling (BLTouch will fit)
One feature I wanted to test was the M3 insert threads. This was something I hadn't tried before and although some of them a used in a manner that would not be mechanically sound actually sort of worked pretty good.. e.g the 12mm X axis shafts held in place by this method means that that the force needed to retain the shaft but not pull the insert from the part is just almost there. the grip where I couldn't pull the shaft through the hole was at the point the grub screw started to deform the part and push the hole away from the shaft.
I bought these from (Australia) Cross Tools PHONE 1800 025 500
http://www.crosstools.com.au/threaded-inserts-for-plastic%2c-wood%2c-injection---rotomolding.html#insertsforplastic
Part: TH-M30-SV
For those not wanting to use inserts for a Beer I could change this to a way easier system that the LulzBot guys could have implemented lol.
Update: in the downloads there is a ZIP file 1st_concept_z_carriage_no_insert.zip which contains the STL's for doing the X Smooth Rods without using the Melt in inserts. These are not tested to date but should work without a problem.
It uses M3 Square nuts... square because at 3mm a hexagon is almost round and it might just spin. So do a search on ebay and get some square nuts they are cheap.
Note: the left hand one has a shouldered hole so you only need nuts at one end... this could also be used for the Heat Insert instead of the z_carriage_motor_ak.stl and save 2 inserts for a rainy day.
Added: Y_axis_linear_rail_clamp_less_2mm.stl with 2mm more clearance for the Y axis bearing block.
Added: Y_axis_endplate_Test.stl this is to make sure the endplates fit the Linear Rails
Added: LulzBot X Carriage_hole_Centers.dxf Showing placement of extruder holes (23mm pitch)
With this cutting list the Max Travel of Z is 250mm. You can achieve 260mm but homing with the raise before descending will catch the fame corner on the X motor.
Parts:
2020 extrusion
4x 500
4x 510
SBR12 12mm Supported Linear Rail (Y axis)
2x 500
SBR12UU Bearing Block (Y axis)
4x bearing block (or three if preferred)
12mm Smoothrod (X axis)
2x 520
10mm Smoothrod (Z axis)
2x 450
10x2 Leadscrew
2x 420
Z X Axis Bearing
Z 2x LM10LUU (long bearing or 4x short)
X 3x LM12UU
Z axis Leadscrew 2x 608Z bearing
T-Slot Slide in T-nuts for 2020 Frame
M5 T nuts x80+ (76 for frame and Y axis only)
Bolts
M5x10 Caphead x80+ (76 for frame and Y axis only)
M5x25 Caphead x11 Yaxis to Main Frame and XY belt pulley +Nyloc nuts
M4x30 Caphead x3 XY Belt tension +Nyloc nuts
M4x20 x8 Mixture of Caphead and Countersunk for X carriage bearings +Nyloc nuts
M3x55 Caphead x8 Yaxis Clamp Blocks +Nyloc nuts
M3x10 Caphead x20 Nema17 motor mount and Zaxis M10x2 nut
GT2 Belt
X aprox 900mm
Y aprox 1000mm
GT2 Pulley
Motor 2x 20 Tooth 5mm shaft (or your motor shaft)
Idler 2x 20 (tooth or not) 5mm
Y AXIS and 200x300 Bed Option:
These files are in a zip file to keep them separate.
I have added the parts needed to use the more STD Y axis you see using 10mm Smooth Rods instead of Supported Linear rails. This is the Wilson II system which not a bed system but has multiple parts to make the bed.
Similar models
thingiverse
free
FLSun i3 Factory Printable Parts Collection (linear rod and bearing version) by macelius
...xis belt tensioner (2 parts)
y-axis bed rail mounts
z-axis top corner brackets - 10mm tall
z-axis top corner brackets - 40mm tall
thingiverse
free
2040 Y axis belt tensioner rebuild for linear rails update by valius983
...1.0.0.1beb4c4dinlu8h
i also added cura file because you need to do mirror model from one that i created to do two pieces you need
thingiverse
free
RoBo3D Y Axis Remix by mkelly
...e bed/plastic. i used 2 part plastic epoxy
suggested material is abs due to bed heat. print at 50% or greater for best results.
thingiverse
free
Y Axis Belt Tensioner by Oblivion
...s to rotate on an axis parallel to the x axis instead of the z axis.
-change mount part to accommodate the new bearing direction.
thingiverse
free
K8200 Y Axis Tensioner by k8200User
...m bearing
1 x 5mm bolt (at least 20mm long)
2 x 5mm washers
1 x 5mm nut
2 x 3mm bolts (at least 15mm long)
2 x 3mm nuts
thingiverse
free
2020 Y upgrade for Wanhao Duplicator i3, Cocoon Create, Maker Select, and Malyan M150 i3 3D printers. by delukart
...m precision shim ( 4 for belt guide-- 2 for idle tensioner )
1x-- new gt2 belt (for new stepper motor position and belt routing)
thingiverse
free
X belt tensioner with 608zz by JulianGu
...rse
belt tensioner for x-axis with a 608zz bearing.
also needed:
m8x30+nut to fit the bearing with the part
m4x50+nut to stretch
thingiverse
free
Linear Rail Y Axis 324mm Wilson LulzBot 2020 by ant0ny
... y axis in place.
8x m3 x 60mm
8x m5 x 25mm
a test part to check if your linear rail will fit before you print a whole end plate.
thingiverse
free
Linear Rail / Tevo Tornado / Z Axis
...e lead screws
6x m5x45mm bolts and nuts for the linear rail mounts/rear z brackets (inner bolts will need to be cut down to size)
thingiverse
free
Improved Anet A8 RepRap X-Axis Belt Tensioner by WedgeSD
...want to wrap the belt around the bearing and insert into the housing then bolt the bearing in place, as shown in the photo's.
Ant0Ny
thingiverse
free
X-Carriage-ENDSTOP by ant0ny
...top in smooth x-axis for prusa i3 with leadscrews
by mazaafin.
this is to use the original geeetech prusa i3 x supplied endstop
thingiverse
free
Mirror Bracket by ant0ny
...the cheap 5mm thick mirrors you can buy from bunnings.
fixings i used where some 3mm (1/8th) x 25mm counter sunk wood screws x 12
thingiverse
free
2020 Extrusion Gusset by ant0ny
...on. there is a left and right if anyone want a on center version i can do that but you would have to print it with more supports.
thingiverse
free
Wilson II 400x400 Bed by ant0ny
...ed
for joined 4 x 200x200 hotbeds together
this is specific to a wilson ii design and bolts to a printed y axis bearing carriage.
thingiverse
free
Nexus 7 Gen1 Case Remix by ant0ny
...e omnimac turnigy 9xr tablet mount by guymccaldin http://www.thingiverse.com/thing:164578
i did the full remix as an alternative.
thingiverse
free
OpenBuilds V Slot Joiner by ant0ny
... but you can try it on the side without, which would be stronger but i figured in this application it wouldn't really matter.
thingiverse
free
Ramps Enclosure 2020 Remix by ant0ny
...age.
note: there is a wide version because i always struggle to make all the wires fit.
http://www.thingiverse.com/thing:1995049
thingiverse
free
2020 aluminum extrusion L shaped joint - Remix by ant0ny
...a quick remix from ameen005.
20 x 20 aluminum extrusion 90deg with pass through for one leg... handy when a 't' wont fit.
thingiverse
free
USB Extension Bracket Wilson 2020 Frame by ant0ny
...usion frame. plugs into the ramps 1.4/arduino usb port
fits the usb cable from ebay here http://www.ebay.com.au/itm/111436428181
thingiverse
free
Wilson II Z Pinion (mod from original) by ant0ny
...fit.
https://github.com/mjrice/wilson2
added marlin 2.0.x config.h file as example of how to setup deploying the rack and pinion.
Taz
thingiverse
free
TAZ by Taz8373
...taz by taz8373
thingiverse
my 1st print
thingiverse
free
Taz Wiper Mount by theFPVgeek
...taz wiper mount by thefpvgeek
thingiverse
lulzbot taz wiper mount
thingiverse
free
Lulzbot Taz Enclosure by MrMcGuire
...lulzbot taz enclosure by mrmcguire
thingiverse
parts for an enclosure for lulzbot taz
thingiverse
free
TAZ by farenthys
...ant taz. need some improvements.
i add .blend file.
new file for some test print
try to cut into 4 part: corpse,leg , arm, teeth
thingiverse
free
Taz by SculptandPrint
...tasmanie est un personnage des looney tunes de la warner bros. pictures. c'est un diable de tasmanie.
sculpt -> zbrushcore
thingiverse
free
Taz Bracelet by blodin
...taz bracelet by blodin
thingiverse
bracelet
thingiverse
free
Looney Tunes TAZ by riccardo3D
...looney tunes taz by riccardo3d
thingiverse
taz from looney tunes hand painted foxsmart brown pla.
thingiverse
free
XLBot - Clone of Taz by Neoprodfx
...xlbot - clone of taz by neoprodfx
thingiverse
my version of taz 4.0, with modifications and new pieces.
z nut is for m8.
thingiverse
free
TAZ LED mount by TickleMancer
...taz led mount by ticklemancer
thingiverse
for my lulzbot taz 3, to better see what's happening.
thingiverse
free
TAZ Wire Clip by jakubk
...the clips should snap into the extruded aluminum channel with some force.
printed using 3mm pla with a 0.5mm nozzle on a taz 5.
Lulzbot
thingiverse
free
LulzBot Rocktomek by LulzBot
...lulzbot rocktomek by lulzbot
thingiverse
https://download.lulzbot.com/3d_models/rocktomek/
thingiverse
free
THE Lulzbot spool holder
...the lulzbot spool holder
thingiverse
stl and ipt topmount spool holder for lulzbot
thingiverse
free
Lulzbot logo by Halg199703
...lulzbot logo by halg199703
thingiverse
this is the lulzbot logo. i also have a file for dual extruder.
thingiverse
free
LulzBot Bio printer Model
...lulzbot bio printer model
thingiverse
this is a model of the lulzbot bioprinter
thingiverse
free
Lulzbot Taz Enclosure by MrMcGuire
...lulzbot taz enclosure by mrmcguire
thingiverse
parts for an enclosure for lulzbot taz
thingiverse
free
Lulzbot Spool Holder by MAKE
...lulzbot spool holder by make
thingiverse
a spool holder for your lulzbot.
thingiverse
free
Lulzbot mini spool holder by chewie80524
...lulzbot mini spool holder by chewie80524
thingiverse
this part holds the spool on a lulzbot mini. this design came from lulzbot.
thingiverse
free
Lulzbot Claystruder by 102drewt
...r for the lulzbot taz 4. every thing is snap together, and it only requires a threaded rod, a nut to fit it, and a stepper motor.
thingiverse
free
Lulzbot Mini Enclosure brackets by chewie80524
...lulzbot mini enclosure brackets by chewie80524
thingiverse
lulzbot taz/mini enclosure brackets.
thingiverse
free
Lulzbot mini toolbox by nicsna
...t mini using cura scale down to 0.97.
hope you like it and make sure to leave some feedback or suggestions for my next design. :)
Custom
thingiverse
free
Custom by frenchpugahuahua
...custom by frenchpugahuahua
thingiverse
customization
thingiverse
free
My Customized WALLY - Wall Plate Customizer
... http://www.thingiverse.com/thing:47956
created with customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=47956
thingiverse
free
Wheel Spacer For Custom Rims Customizer by Thor3D
...l spacer for custom rims customizer by thor3d
thingiverse
this customizer will generate custom wheel spacers for non-stock rims.
thingiverse
free
Customized MEEM
...customized meem
thingiverse
mse 4777 customize mini project openscad
a customizer for all your meem printing needs.
thingiverse
free
Custom keychain
...custom keychain
thingiverse
custom keychain that you can edit
thingiverse
free
My Customized SLIDE | Smartphone Slider - Customizer Edition
... http://www.thingiverse.com/thing:74307
created with customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=74307
thingiverse
free
Custom Cup
...custom cup
thingiverse
enter custom dimensions for making a cup to fit any needs!
thingiverse
free
My Customized GoPro
... http://www.thingiverse.com/thing:62800
created with customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
free
My Customized card
...//www.thingiverse.com/thing:729844
created with customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=729844
thingiverse
free
Custom Realacc Custom Pod by Thestealth
...custom realacc custom pod by thestealth
thingiverse
nice for my own x110 frame is a scale from the x210 realacc
6
thingiverse
free
Yellow Ring (6 of 6)
...yellow ring (6 of 6)
thingiverse
last one! please like and collect!
thingiverse
free
NO PHONE v.6/6+ by habib010
... v.6/6+ by habib010
thingiverse
new model based of the iphone 6 & 6+
thin is a prop of the "no phone" series vol.1
thingiverse
free
Gear Bearing 6 in 6 by suvakov
...gear bearing 6 in 6 by suvakov
thingiverse
pla / 0.2mm / infill 10% / no support
thingiverse
free
iPhone 6 / 6 plus screw tray by Anzymanz
...iphone 6 / 6 plus screw tray by anzymanz
thingiverse
iphone 6 / 6 plus screw tray
thingiverse
free
Werkzeugleiste 6 / Toolbar 6 by CBiker
...werkzeugleiste 6 / toolbar 6 by cbiker
thingiverse
werkzeughalter fuer verschiedene werkzeuge mit magnethalter.
thingiverse
free
iPhone 6 and 6 Plus by mattbeechan
...ngiverse.com/jerware) suggested dimensions.
6 plus in two pieces for small print beds. http://www.thingiverse.com/thing:458659
thingiverse
free
Numero 6 by Xbertus
...numero 6 by xbertus
thingiverse
numero 6
thingiverse
free
Iphone 6+ by nitsua8
...iphone 6+ by nitsua8
thingiverse
iphone 6+
thingiverse
free
dress2-6 by paulchancan
...dress2-6 by paulchancan
thingiverse
dress2-6
thingiverse
free
Bird-6- by Centaur
...bird-6- by centaur
thingiverse
bird-6-
Remix
thingiverse
free
Extruder Spinner Remix of Remix of Remix
...d
feel free to print or remix and don't forget to post it.
if you find it useful you can send tip or buy me a coffe. thanks.
thingiverse
free
Predator mask (remix of remix)
...predator mask (remix of remix)
thingiverse
just cool mask :)
thingiverse
free
REMIX by nbvgbbvv
...remix by nbvgbbvv
thingiverse
remix
thingiverse
free
remix by Alejandragr
...remix by alejandragr
thingiverse
remix
thingiverse
free
remixed by mkj
...remixed by mkj
thingiverse
this is remix comment
thingiverse
free
UK Remix of a Remix by ukcat
...for a big kentucky wildcats' fan birthday!
update 3/18/14: uploaded a version with the uk stuff, but no initials at bottom.
thingiverse
free
Remix Mystery
...remix mystery
thingiverse
this is for a class remix assignment.
thingiverse
free
Slight Remix of Tundra Remix by PyrOverkill
...pyroverkill
thingiverse
slight modification of the my remix of the bakflip handle. better resolution on the name plate and logo.
thingiverse
free
Arrowhead Remix
...arrowhead remix
thingiverse
remixing my og arrowhead
thingiverse
free
Remix Project
...remix project
thingiverse
this is my submission for the thingiverse remix project.