Thingiverse
![LowRider2 XZ Joint by ValeryOD](/previews/8377928.jpg)
LowRider2 XZ Joint by ValeryOD
by Thingiverse
Last crawled date: 3 years, 2 months ago
This is a very rigid XZ joint for LowRider 2 (25mm).
You will need the following parts for assembly:
x8 M4 60mm socket head cap screws
x8 M4 Locknuts
x8 M3 Rivets
x4 (at least) M3 10mm flat head screws
Zip ties for the belt can be mounted from any side. I will design belt tensioners for the rivet mounts some time too.
The rivets shall be inserted using a soldering iron, but be careful not to overheat.
The Rigidity Frame is to be screwed to the corresponding slot in the main body. It allows to avoid any supports while printing.
Hope you like the design, if not - .f3d file is also attached.
Looking forward to your makes and comments!
UPDATE #1: The "Y Bottom" part needs to be updated as well due to a slight offset in original Z rails. STL and source files included.
You will need the following parts for assembly:
x8 M4 60mm socket head cap screws
x8 M4 Locknuts
x8 M3 Rivets
x4 (at least) M3 10mm flat head screws
Zip ties for the belt can be mounted from any side. I will design belt tensioners for the rivet mounts some time too.
The rivets shall be inserted using a soldering iron, but be careful not to overheat.
The Rigidity Frame is to be screwed to the corresponding slot in the main body. It allows to avoid any supports while printing.
Hope you like the design, if not - .f3d file is also attached.
Looking forward to your makes and comments!
UPDATE #1: The "Y Bottom" part needs to be updated as well due to a slight offset in original Z rails. STL and source files included.
Similar models
thingiverse
free
![Direct Drive Extruder MK8 by squareoctopus](/t/8760186.jpg)
Direct Drive Extruder MK8 by squareoctopus
...4 x 16mm hex-head screw
4 m4 x 20mm screw
1 m4 x 30mm screw
2 m4 x 12mm countersunk-head screw
1 compression spring
1 604 bearing
thingiverse
free
![Anet A8 Y-belt tensioner V2 by YoshiCat](/t/8764721.jpg)
Anet A8 Y-belt tensioner V2 by YoshiCat
...vot point.
i used three m3 washers on the bearings, one between the bearings and the other two between the bearing and the frame.
thingiverse
free
![Floppy Square-5 by Decoder_Pr0](/t/8283045.jpg)
Floppy Square-5 by Decoder_Pr0
... 7cm x 7cm x 3.5cm
print:
corner x8
edge_p1 x8
edge_p2 x8
center x2
(only if needed) screw base x1
(only if needed) screw head x2
thingiverse
free
![X Belt Tensioner and XZ Side Belt Remix](/t/4904103.jpg)
X Belt Tensioner and XZ Side Belt Remix
... xz side belt as well. you'll still need the tensioner small part from tailslide's original post.
please post your makes!
thingiverse
free
![525 MPCNC (IE F-25mm OD) - Corner Block (Optimised) by ValeryOD](/t/8244311.jpg)
525 MPCNC (IE F-25mm OD) - Corner Block (Optimised) by ValeryOD
...able.
can't thank enough the author for excellent design, my mpcnc became far more rigid with these corner blocks. nice work!
thingiverse
free
![Z belt tensioner - adjustable by thicc_nugget](/t/8016895.jpg)
Z belt tensioner - adjustable by thicc_nugget
... the tensioner on a 2020 aluminum profile and a longer m3 screw, some nuts and (if necessary) some washers to fix the gt2 pulley.
thingiverse
free
![X_Belt tensioner for tronxy x8](/t/4922491.jpg)
X_Belt tensioner for tronxy x8
...omanded
08 oct 19 update
added a little knob to the files so the screw will not dig into the printer plastic when tension is high
thingiverse
free
![Anycubic i3 Mega Y-axis Belt Tensioner](/t/4833085.jpg)
Anycubic i3 Mega Y-axis Belt Tensioner
... m4 nuts
b) 2 x 40mm m4 screws (allen head din-912)
c) 2 x 20mm m3 screws
d) 1 x 12mm m3 screw
e) 1 x m3 nut
f) 3d printed parts
thingiverse
free
![SKR 1.4 Case with 80mm fan by frostin2k](/t/8094066.jpg)
SKR 1.4 Case with 80mm fan by frostin2k
...the mounting pads. for the fan you need m4 bolts with nuts or just use screws (6mm or longer).
edit:
use v4.
removed old designs.
thingiverse
free
![Octoprint Pi3 V-slot 40mm Adapter for Case (Ender 5 & more) by Nomade12](/t/8037747.jpg)
Octoprint Pi3 V-slot 40mm Adapter for Case (Ender 5 & more) by Nomade12
... version)
2x m4 button head socket screw (for screw version)
2x m4 v-slot nut
this is a w.i.p.
i will update this design and info
Valeryod
thingiverse
free
![Oblique penholder by ValeryOD](/t/8026442.jpg)
Oblique penholder by ValeryOD
...oken penholder or cut one out yourself if you have the required tools.
feel free to make improvements - fusion 360 file attached.
thingiverse
free
![Stand for TFT35 V3 case by ValeryOD](/t/8177654.jpg)
Stand for TFT35 V3 case by ValeryOD
...want to screw it directly to the desk.
i insert the .f3d file for you to adjust the dimensions, add the hex holes if needed, etc.
thingiverse
free
![Oblique penholder 2 by ValeryOD](/t/8016147.jpg)
Oblique penholder 2 by ValeryOD
...ture).
fusion 360 file is attached, any enhancements are welcome!
i'll also be very thankful if you share your makes with us.
thingiverse
free
![Lens (convex) knife sharpening tool by ValeryOD](/t/8006787.jpg)
Lens (convex) knife sharpening tool by ValeryOD
...39;t calculate the exact geometry parametrically, so feel free to adjust any value to your needs in the fusion 360 file attached.
thingiverse
free
![Smoking pipe mouthpiece (for Savinelli "Miele") by ValeryOD](/t/8342919.jpg)
Smoking pipe mouthpiece (for Savinelli "Miele") by ValeryOD
...our own pipe before printing, unless you have the exact same model.
upd: extended length for the filter hole, minor improvements.
thingiverse
free
![525 MPCNC (IE F-25mm OD) - Corner Block (Optimised) by ValeryOD](/t/8244311.jpg)
525 MPCNC (IE F-25mm OD) - Corner Block (Optimised) by ValeryOD
...able.
can't thank enough the author for excellent design, my mpcnc became far more rigid with these corner blocks. nice work!
Lowrider2
thingiverse
free
![LowRider2 Z-Endstop by 4noxx](/t/8039831.jpg)
LowRider2 Z-Endstop by 4noxx
...lowrider2 z-endstop by 4noxx
thingiverse
lowrider2 z-endstop for 25mm and 25.4 pipes
thingiverse
free
![LowRider2 / MPCNC Autosquare Case by 4noxx](/t/8030088.jpg)
LowRider2 / MPCNC Autosquare Case by 4noxx
...lowrider2 / mpcnc autosquare case by 4noxx
thingiverse
lowrider2 / mpcnc autosquare
potentiometer 5mm
push button 16mm
thingiverse
free
![LowRider2 belt tensioner by 4noxx](/t/8049766.jpg)
LowRider2 belt tensioner by 4noxx
....thingiverse.com/thing:3026040https://www.thingiverse.com/thing:3064287
spanner_fest_v2.stl
hole for m4 is 20mm deep instead 4mm
thingiverse
free
![LowRider2 Dust Shoe by 4noxx](/t/8026584.jpg)
LowRider2 Dust Shoe by 4noxx
...shoe
bom:
front and back part
18x m3x10 or larger
tablecloth pvc transparent 1-2mm
02.01.2021
add a second version for m3 inserts
thingiverse
free
![Rails for LowRider2 CNC by swepeter](/t/8073173.jpg)
Rails for LowRider2 CNC by swepeter
...this:https://www.thingiverse.com/thing:2368805
thanks godler
alos modded the y plate fromhttp://www.thingiverse.com/thing:3064287
thingiverse
free
![65 mm Spindle Mount for LowRider2 by quirxi](/t/9226697.jpg)
65 mm Spindle Mount for LowRider2 by quirxi
... a 65 mm watercooled (china) spindle to the original 611-plate of the lowrider2 (see: https://www.thingiverse.com/thing:3064287).
thingiverse
free
![Lowrider2 separación extra wheels by pericomart](/t/8114978.jpg)
Lowrider2 separación extra wheels by pericomart
...- aporta más estabilidad al mantener la rueda a 90º gradospermite mantener la ruedas a 90º con respecto al eje y.
se necesitan 4.
thingiverse
free
![lowrider2-611-plate-2_25.4mm by peterfosseus](/t/9253779.jpg)
lowrider2-611-plate-2_25.4mm by peterfosseus
...e, then a new aluminum one :)
https://docs.v1engineering.com/lowrider/
openscad file for your convenience. - http://openscad.org/
thingiverse
free
![Lowrider2 eje Y Tirantes by pericomart](/t/8353738.jpg)
Lowrider2 eje Y Tirantes by pericomart
...or estabilidad al eje y
incluyo versión para 25mm y para 25,4mm
se debe imprimir con soporte, el de tipo árbol da buen resultado.
thingiverse
free
![LowRider2 Vac Adapoter for 1.875 Hose by C6SUMMER](/t/8005469.jpg)
LowRider2 Vac Adapoter for 1.875 Hose by C6SUMMER
...lowrider2 vac adapoter for 1.875 hose by c6summer
thingiverse
hose adapter to fit the lowrider vacuum base fitting.
Xz
turbosquid
$16
![Sony Xperia XZ](/t/13474231.jpg)
Sony Xperia XZ
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$25
![Sony Xperia XZ Premium](/t/13378588.jpg)
Sony Xperia XZ Premium
...eria xz premium for download as 3ds, obj, fbx, blend, and stl on turbosquid: 3d models for games, architecture, videos. (1191731)
turbosquid
$14
![XZ two axis conveying mechanism](/t/13523089.jpg)
XZ two axis conveying mechanism
...z two axis conveying mechanism for download as ige and sldpr on turbosquid: 3d models for games, architecture, videos. (1223721)
turbosquid
$20
![Sony Xperia XZ All Colors](/t/13474214.jpg)
Sony Xperia XZ All Colors
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$18
![The Xz axis manual adjustment mechanism](/t/13523034.jpg)
The Xz axis manual adjustment mechanism
...tment mechanism for download as 3ds, ige, obj, stl, and sldas on turbosquid: 3d models for games, architecture, videos. (1243040)
turbosquid
$2
![Sony Xperia XZ Mineral black](/t/13474229.jpg)
Sony Xperia XZ Mineral black
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
![Sony Xperia XZ Forest blue](/t/13474230.jpg)
Sony Xperia XZ Forest blue
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
![Sony Xperia XZ Deep pink(1)](/t/13474217.jpg)
Sony Xperia XZ Deep pink(1)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
thingiverse
free
![XZ-Alignment by JMDesigns](/t/8640247.jpg)
XZ-Alignment by JMDesigns
...igns
thingiverse
xz-alignment dient der ausrichtung der xz-achsen bei i3 druckern (z.b. wanhao duplicator i3, prusa i3, usw...)
thingiverse
free
![XZ Cobler by TrisectDevelopment](/t/8281577.jpg)
XZ Cobler by TrisectDevelopment
...xz cobler by trisectdevelopment
thingiverse
this part if holding the gantry profiles together.
Joint
turbosquid
$5
![Joint](/t/13305595.jpg)
Joint
...turbosquid
royalty free 3d model joint for download as blend on turbosquid: 3d models for games, architecture, videos. (1179882)
3d_export
$5
![joint handle](/t/11920769.jpg)
joint handle
...joint handle
3dexport
joint handle
3d_export
$5
![knuckle joint](/t/11464408.jpg)
knuckle joint
...knuckle joint
3dexport
this is a 3d model of knuckle joint
3d_export
$5
![Knuckle Joint](/t/12580427.jpg)
Knuckle Joint
...knuckle joint
3dexport
industry use knuckle joint
3ddd
$1
![PENTA Joint](/t/971148.jpg)
PENTA Joint
...penta joint
3ddd
penta
http://www.lampcommerce.com/en/catalogue/brands/penta-light/joint-floor-lamp
turbosquid
$49
![Joint | Project](/t/13291517.jpg)
Joint | Project
...squid
royalty free 3d model joint | project for download as on turbosquid: 3d models for games, architecture, videos. (1297983)
turbosquid
$10
![universal joint](/t/13241866.jpg)
universal joint
...squid
royalty free 3d model univresal joint for download as on turbosquid: 3d models for games, architecture, videos. (1309400)
turbosquid
$15
![Joint Ashtray](/t/13243424.jpg)
Joint Ashtray
...squid
royalty free 3d model joint ashtray for download as ma on turbosquid: 3d models for games, architecture, videos. (1199702)
turbosquid
$5
![Unrolled joint](/t/13404744.jpg)
Unrolled joint
...e 3d model unrolled joint for download as blend, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1577889)
3d_export
$5
![Cardan Joint 3D Model](/t/132384.jpg)
Cardan Joint 3D Model
...cardan joint 3d model
3dexport
cardan joint
cardan joint 3d model fau 71171 3dexport