Similar models
thingiverse
free
Loupedeck CT Stand
...and to angle the loupedeck ct up a little. just needs 4x m3 nuts and 4xm3 bolts to finish.
printed on a prusa i3 mk3s at .3 draft
thingiverse
free
Loupedeck Stand by zcohen
...crews. i dont have space to mount it in my office so if someone prints it, please post a picture so i can see if it works or not.
thingiverse
free
Loupedeck Live Stand/Feet by MrPresident2
...em feet, they are longer than the original feet thus will give you a higher angle.
hope you like it, share with us if you make it
thingiverse
free
Loupedeck CT Stand (untested) by Juulmo
...ed) by juulmo
thingiverse
slightly modified loupdeck stand to make it more sturdy and printable in one piece. no supports needed
thingiverse
free
Propeller stand
... print a propeller with a 3mm hole to fit onto this stand.
i printed this on a prusa mk3s with no supports. prints perfectly.
thingiverse
free
phone stand easy to print by FLIPPIN-3D
...phone stand easy to print by flippin-3d
thingiverse
3d printed phone stand easy to print
thingiverse
free
Phone stand by An29
...phone stand by an29
thingiverse
phone stand. easy to print. easy to print.
thingiverse
free
otter with stand to support print by jdtoken
...otter with stand to support print by jdtoken
thingiverse
otter with stand to support print
thingiverse
free
Fast Printing Phone Stand by ddude3548
...ddude3548
thingiverse
print this phone stand in pieces and assemble for faster printing.
print 1x stand_brace and 2x stand_side.
thingiverse
free
Stand Grip by BenoitDFR
...stand grip by benoitdfr
thingiverse
stand grip for the dfr stand.
printed in tpu
Cescop
thingiverse
free
Lipo 1S Organizer by cescop
...lipo 1s organizer by cescop
thingiverse
my organizer for li-po 1s for my tinyhawk ii.
thingiverse
free
Li-Po 1S Organizer x20 Li-Po by cescop
... by cescop
thingiverse
organizer for 20 li-po batteries, if you like to fly your tiny fpv quad this is a must have on your desk.
thingiverse
free
Lipo 1S Organizer x10 Li-Po by cescop
...one side with empty label and one side with full label, then use the connector orientation to specify the status of each battery.
Loupedeck
thingiverse
free
Loupedeck CT Stand
...and to angle the loupedeck ct up a little. just needs 4x m3 nuts and 4xm3 bolts to finish.
printed on a prusa i3 mk3s at .3 draft
thingiverse
free
Loupedeck Stand by zcohen
...crews. i dont have space to mount it in my office so if someone prints it, please post a picture so i can see if it works or not.
thingiverse
free
Loupedeck Live Stand/Feet by MrPresident2
...em feet, they are longer than the original feet thus will give you a higher angle.
hope you like it, share with us if you make it
thingiverse
free
Loupedeck CT Stand (untested) by Juulmo
...ed) by juulmo
thingiverse
slightly modified loupdeck stand to make it more sturdy and printable in one piece. no supports needed
Stand
thingiverse
free
Stand-stand by Fank86
... all your troubles go away, .1mm at a time!
and no, i did not make this in 15 seconds to poke fun at all the stands on this site.
thingiverse
free
stand
...stand
thingiverse
a stand
thingiverse
free
A stand
...a stand
thingiverse
a stand.
thingiverse
free
Stand
...stand
thingiverse
this is a stand, nothing more !
thingiverse
free
stand
...stand
thingiverse
this is a stand that you can put things on
thingiverse
free
Headset stand with phone stand
...dset stand that doubles as a phone stand, the phone also can be charged while on the stand.
leave a comment if you have feedback
thingiverse
free
hairdryer stand and Curling iron stand
...hairdryer stand and curling iron stand
thingiverse
hairdryer stand and curling iron stand
thingiverse
free
Inbus Stand / Inbuskey Stand
...workshop.
this inbuskeys fitts perfectly in that stand:
8 ; 6 ; 5 ; 4 ; 3 ; 2,5 ; 2
enjoy your print :)
comment below if it works
thingiverse
free
Stand by cmaines
...stand by cmaines
thingiverse
stand
thingiverse
free
stand by Syzguru11
...stand by syzguru11
thingiverse
stand