Thingiverse
Long clamp by Giovanni1965
by Thingiverse
Last crawled date: 3 years, 4 months ago
Morsetto lungo (1 metro o più) utilizza un tubo da 25 mm spesso 1,5 mm, potete farli anche 2 metri se vi servono, stampate i pezzi come sono messi e su alcuni attivate i supporti per il bed, riempimento al 50% io ho usato petg e sono molto robusti, c'è anche una dima che serve per fare i fori tutti in asse, molto utile accoppiata a un indispensabile trapano a colonna, vi servono due viti M5 a brugola da 35 mm con due dadi M4 per bloccare la parte della vite, prima di montarla sulla barra inserite il dado M12, per montarla sulla barra consiglio della colla bicomponente, poi quando è asciutta forate per fare passare le viti, poi vi serve un pezzo di barra filettata M12 con un dado normale, uno cieco e una rondella, all'estremità della barra mettete un dado e foratelo inserendo un perno inb modo che resti bloccato, tra il dado che spinge e la stampa della parte mobile inserite una rondella M10 per assorbire l'attrito, un po di grasso è utile, poi vi serve una vite da 40 mm M6 per bloccare la parte posteriore, ho fatto il primo foro lungo la barra a 50 mm dalla fine, i successivi ogni 70 mm.
Long clamp (1 meter or more) uses a 25mm 1.5mm thick tube, you can make them even 2 meters if you need, print the pieces as they are placed and on some activate the supports for the bed, 50% filling i I used petg and they are very sturdy, there is also a template that is used to make the holes all in axis, very useful combined with an indispensable column drill, you need two M5 35 mm Allen screws with two M4 nuts to lock the part of the screw, before mounting it on the bar insert the M12 nut, to mount it on the bar I recommend the two-component glue, then when it is dry drill to pass the screws, then you need a piece of threaded bar M12 with a normal nut, one blind and a washer, at the end of the bar put a nut and drill it by inserting a pin so that it remains blocked, between the nut that pushes and the press of the moving part insert an M10 washer to absorb the friction, some grease is useful, then you need a 40mm M6 screw to lock the back, I made the first hole along the bar 50 mm from the end, the next every 70 mm.
Long clamp (1 meter or more) uses a 25mm 1.5mm thick tube, you can make them even 2 meters if you need, print the pieces as they are placed and on some activate the supports for the bed, 50% filling i I used petg and they are very sturdy, there is also a template that is used to make the holes all in axis, very useful combined with an indispensable column drill, you need two M5 35 mm Allen screws with two M4 nuts to lock the part of the screw, before mounting it on the bar insert the M12 nut, to mount it on the bar I recommend the two-component glue, then when it is dry drill to pass the screws, then you need a piece of threaded bar M12 with a normal nut, one blind and a washer, at the end of the bar put a nut and drill it by inserting a pin so that it remains blocked, between the nut that pushes and the press of the moving part insert an M10 washer to absorb the friction, some grease is useful, then you need a 40mm M6 screw to lock the back, I made the first hole along the bar 50 mm from the end, the next every 70 mm.
Similar models
thingiverse
free
Attacco per cinghia per trasporto stampante by tecnicotibetano
...ete in foto è stato stampato in nylon.
viene montato sulla sommità della stampante sfruttando il distanziale e le viti esistenti.
thingiverse
free
Supporto sbarra letto a castello Moretti compact by roberto3d
...che ne ha aumentato la resistenza, tanto da doverlo bucare con un trapano, per poter infilare la vite. il tutto realizzato in pla
thingiverse
free
Avvolgitore bobine mulinelli da pesca by loscorpione
... supporto della bobina. più la molla è compressa e più il rocchetto viene frenato.
spero che sia di vostro gradimento e di aiuto.
thingiverse
free
Sidewinder X1 flat X support with 40 mm fan by Giovanni1965
...sibility of loss of steps, as a fan use a silent one, i used a noctua, it does not need to blow hard, just a little and it cools.
grabcad
free
Da Vinci - globoid worm (1)
... e così è ffatto una vite sanza fine. el braccio della rota di mezo ussciendo d'una vite entra nell' altra e poi ritorna.
thingiverse
free
SUPPORTO LUCE ANTERIORE BROMPTON by Jamensolo
...), n.4 rondelle larghe per m5, n.2 dadi m5.
il tempo di stampa del g-code è più lungo in quanto le velocità sono state diminuite.
thingiverse
free
Box TFT35-E3 V3 by Giovanni1965
...hat goes on the frame (for profiles 20x20 or 20x40) you need two screws a 10 mm allen key and two hammer nuts for 20x20 profiles.
thingiverse
free
placchetta per schermo lcd by Valdan
...rmo. c'è anche lo spazio per la manopola a rotella ed ho inserito il tasto per il reset.
appena ho tempo vi allego le foto :)
grabcad
free
double worm globoidal screw
...ità delle materie prime impiegate e ad appropriati trattamenti termici, assicura una lunga durata alle viti a ricircolo di sfere.
thingiverse
free
attacco luce per Brompton by maurovendetti
...pimento del 40%. sempre per garantire la massima resistenza dell'adattatore suggerisco di stamparlo orientato in orizzontale.
Giovanni1965
thingiverse
free
Pacman by Giovanni1965
...cman by giovanni1965
thingiverse
and yes .... i could not resist, even i created my pacmam ...., try to paint it better than me.
thingiverse
free
M4 knob by Giovanni1965
...giovanni1965
thingiverse
m4 knob with nut to be inserted, for any use, also to adjust the bed of 3d printers with large shelves.
thingiverse
free
M3 knob with recessed nut by Giovanni1965
...anni1965
thingiverse
m3 knob with recessed nut, height 10 mm diameter 20 mm, useful for leveling easily the bedi of 3d printers.
thingiverse
free
hole distance meter by Giovanni1965
... tighten the screw and use a gauge to read the hole center spacer.
to assemble it you need two m3 nuts and a 30 mm long m3 screw.
thingiverse
free
Profile cap X 20x60 mm by Giovanni1965
...giovanni1965
thingiverse
tappo profilato x 20x60 mm per sidewinder x1/genius.
profile cap x 20x60 mm for sidewinder x1 / genius.
thingiverse
free
Anet A8 Z-axis regulator by Giovanni1965
...iovanni1965
thingiverse
second version of the z-axis regulator for anet a8, you will need a 30 mm long m3 screw and two m3 nuts
thingiverse
free
Simple Z axis controller by Giovanni1965
...t, requires two m4 nuts and a 4 cm m4 screw, it is necessary to insert the nuts into the seat of the knob and of the upper block.
thingiverse
free
100x60 mm hinge by Giovanni1965
....
hinge 100x60 mm, very sturdy, as a pin use an m4 threaded bar or a 4 mm rod, you can use it as a hinge for garage doors etc ...
thingiverse
free
Anet A8 X Tensioner by Giovanni1965
...order to center the bearing, which you can put the original one or a toothed one, do not add too many ranelle left a bit of play.
thingiverse
free
Modify Anet A8 frame by Giovanni1965
...h sandpaper, printed as the file is done by enabling the supports for parts in contact with the bed, serves for the bearing seat.
Clamp
3d_export
$11
clamp
...clamp
3dexport
clamp
3ddd
free
Clamp
... enricо zanolla , капитоне
дизайнерenrico zanollмодель clamp
3ddd
$1
Clamp
...ricо zanolla , капитоне
дизайнеры
enrico zanolla
andrea di filippo
модель clamp
dzstudio
3d_export
free
clamp
...clamp
3dexport
simple clamp model, more free 3d models here:
3d_export
$5
clamping handle
...clamping handle
3dexport
clamping handle
3ddd
$1
Clamp / DZstudio
... dzstudio , капитоне
люстра clamp от dzstudio/enrico zanolla(италия).
3ddd
$1
Светильник Clamp
...светильник clamp
3ddd
clamp
стеганый светильник clamp в двух цветах в черном и белом.
turbosquid
$29
clamp
...ty free 3d model clamp for download as 3ds, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1442049)
turbosquid
$29
clamp
...ty free 3d model clamp for download as 3ds, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1442041)
3d_export
$5
Clamp-14
...clamp-14
3dexport
3d model of clamp name 14
Long
3d_export
free
Long dress with long sleeves
...long dress with long sleeves
3dexport
long dress with a side cut and long sleeves.<br>with uv. no textures
3d_export
$5
long foot
...long foot
3dexport
long foot
design_connected
$16
Long John
...long john
designconnected
rubn long john computer generated 3d model. designed by hoflin, niclas.
3d_export
$5
Long monster
...long monster
3dexport
i`m beginer in 3d modeling.this is my first project - long monster.
design_connected
$18
Long Pot
...long pot
designconnected
ligne roset long pot computer generated 3d model. designed by sempé, inga.
design_connected
$16
Welles Long
...welles long
designconnected
gabriel scott welles long computer generated 3d model. designed by kakon, gabriel.
3ddd
free
Extra Long
...ики fantoni, италия. имеет подсветку ( зеленая или белая). передняя панель выполнена из аккустических панелей.
текстуры в архиве.
3ddd
$1
Светильник Long and Hard
...к long and hard
3ddd
flos , long and hard
светильник long and hard от flos, с текстурами
turbosquid
$4
Long dagger
...urbosquid
royalty free 3d model long dagger for download as on turbosquid: 3d models for games, architecture, videos. (1639425)
turbosquid
$1
Long Axe
...e
turbosquid
royalty free 3d model long axe for download as on turbosquid: 3d models for games, architecture, videos. (1274953)