Thingiverse
LG840g-Cellphone-IpodShuffleCase by rickswirebox
by Thingiverse
Last crawled date: 3 years, 1 month ago
For LG840G Cell Phones
See also my version without the ipod-shuffle case. Just a cover. http://www.thingiverse.com/thing:658862
Wanted to make use of my new ipod Shuffle and have with me when i wanted it. Use it sometimes plugged into my car stereo.
It prints fine. One thing to think of before printing is, to print separately. Do so because the phone-Clip part that pushes down over the ipod case part needs to print slower, about 20 to 30mm/s, while the case pictured was printed at 80mm/s. The phone-clip has the thin small finger clips which need to print slowly.
Works out nice because the phone-clip part will wear out with a finger clip breaking after a few months of pocket use. They print quickly.
Don't forget to use support for the phone-clip. Hate it, but the only way i could think to get all parts in and printable. You may have some areas that may need gluing some velvet or paper in to give a bit of more holding on the ipod case part. For a more of a snap in effect.
Hope you enjoy, Rick.
Note: The picture shows a small piece of thin card stock glued inside the top finger on the phone-clip part. The updated version 4 with the download should fix this without any card stock needed.
Update: Also wanted to add that the fingers may print a bit loose and not have the snap-in on the phone you may want. The thing i did with mine is; use a micro torch or maybe a hair drier to warm the top single finger and squeeze it in a bit. Should work fine and have the snap-in you like.
See also my version without the ipod-shuffle case. Just a cover. http://www.thingiverse.com/thing:658862
Wanted to make use of my new ipod Shuffle and have with me when i wanted it. Use it sometimes plugged into my car stereo.
It prints fine. One thing to think of before printing is, to print separately. Do so because the phone-Clip part that pushes down over the ipod case part needs to print slower, about 20 to 30mm/s, while the case pictured was printed at 80mm/s. The phone-clip has the thin small finger clips which need to print slowly.
Works out nice because the phone-clip part will wear out with a finger clip breaking after a few months of pocket use. They print quickly.
Don't forget to use support for the phone-clip. Hate it, but the only way i could think to get all parts in and printable. You may have some areas that may need gluing some velvet or paper in to give a bit of more holding on the ipod case part. For a more of a snap in effect.
Hope you enjoy, Rick.
Note: The picture shows a small piece of thin card stock glued inside the top finger on the phone-clip part. The updated version 4 with the download should fix this without any card stock needed.
Update: Also wanted to add that the fingers may print a bit loose and not have the snap-in on the phone you may want. The thing i did with mine is; use a micro torch or maybe a hair drier to warm the top single finger and squeeze it in a bit. Should work fine and have the snap-in you like.
Similar models
thingiverse
free
iPod Shuffle Case by c_bednar
...ipod shuffle case by c_bednar
thingiverse
thin wall case for ipod shuffle.
thingiverse
free
Ipod Shuffle by Hotrods2Hybrids
...shuffle case remixed into a childs toy phone - her name was merin if you want a different name let me know or remix for yourself!
cg_trader
free
ipod shuffle
...odel of an ipod shuffle. hope it helps you with anything. ipod apple shuffle music audio electronics phones small appliance phone
thingiverse
free
Fairphone 3+ Snap Fit Case by s_40
...e to print pla snap fit phone cases. they might help as a starting point to get the settings right for your printer and material.
thingiverse
free
Shims for 10/22 with magpul stock
.... you may or may not have to slighlty ream the hole in the washer. these parts are very thin, use the appropriate print settings.
thingiverse
free
Fairphone 3+ Snap Fit Case by s_40
...frame and one lower part. version one and two have different geometrys in the snap fit. v1 is easy to open, v2 is harder to open.
thingiverse
free
Official Standard Ipod 4 Case by 3D_Printable
...oblems with other ipod case files because they were mesh .stl files. these files should solve that problem if you are having it.
thingiverse
free
Big Clip with Mount by rj11
...gy part. it is held together with an m4x40 screw and a locknut. if you want to attach it to the mount, you need an m4x50 screw.
thingiverse
free
USB-C charger enclosure (for combining with other prints) by toozinger
...ore robust version later).
the last picture shows where i have used this enclosure with a person phone stand (still in progress).
thingiverse
free
Foldable Phone Stand by kaxorpie
...he updated stl file because it is better. i left the original up because it is marginally slimmer, but i prefer the updated one.
Rickswirebox
thingiverse
free
Oral-B Tooth Brush Cover and Wall Mount by rickswirebox
...ce would be for mounting on a wall. mount it and then use double stick tape on the cover.
hope you enjoy. happy printing !! :)
thingiverse
free
Clock-Dial-Floating by rickswirebox
...dial-floating by rickswirebox
thingiverse
5-3/4 inch diameter round with 1/2 inch numbers.
may be glued to most anything.
enjoy.
thingiverse
free
Flour Scoop/Shaker/Duster by rickswirebox
...ur for biscuits and other makers with a built-in shaker.
please note: this is 4 inches tall and needs room to print.
enjoy, rick.
thingiverse
free
Clothesline Reel by rickswirebox
...d useful and yours prints well. happy 3d printing!!
oh! as well, please post a picture of your make. will love to see one made !!
thingiverse
free
Sandwich-Pack by rickswirebox
...top should slip right over the bottom and push down on the sandwiches keeping them ready to eat.
enjoy, happy printing....... :)
thingiverse
free
Ipad/Tablet palm rests by rickswirebox
... notes or draws on tablet/ipad needs one of these or both.
makes note taking and drawing a breeze.
thanks, happy printing. :) .
thingiverse
free
electronic-Component-tester-enclosure by rickswirebox
...a small amount but will make much more durable. after all that's why i made the enclosure to start with to protect the board.
thingiverse
free
Ipod Shuffle Wall Mount Hanger Hooks by rickswirebox
...the top layers should smear or blob-up during printing.
hope you find use for and enjoy yours as i do mine,
happy printing, rick.
thingiverse
free
Fishing Cane Pole Car Window Hooks by rickswirebox
...when it comes to them holding a heavy load, yet cane poles are normally lite weight. please keep this in mind on hot summer days.
Cellphone
3d_ocean
$17
Apple Mac Pack
...pack 3docean 3d models 6s apple best black blender cellphone device el capitan gadget gold imac ios9 iphone iphone...
3d_ocean
$15
Note 5 Element 3D Model
...note 5 element 3d model 3docean 3ds max cellphone 3d cinema 4d element 3d note 5 note5 phone...
3d_export
$29
Apple iPhone 6S Gold 3D Model
...3d model 3dexport apple iphone 6s electronics technology gadgets cellphone cellular phone smartphone apple iphone 6s gold 3d model...
cg_studio
$30
Microsoft Lumia 535 Blue3d model
...model cgstudio microsoft lumia 535 phone windows 8.1 cell cellphone smartphone .fbx .obj .max .c4d - microsoft lumia 535...
cg_studio
$30
Microsoft Lumia 535 Orange3d model
...model cgstudio microsoft lumia 535 phone windows 8.1 cell cellphone smartphone .max .c4d .obj - microsoft lumia 535 orange...
cg_studio
$30
Microsoft Lumia 535 Green3d model
...model cgstudio microsoft lumia 535 phone windows 8.1 cell cellphone smartphone .fbx .obj .max .c4d - microsoft lumia 535...
cg_studio
$30
Microsoft Lumia 535 White3d model
...model cgstudio microsoft lumia 535 phone windows 8.1 cell cellphone smartphone .fbx .obj .max .c4d - microsoft lumia 535...
3d_ocean
$14
Sliding Mobile Phone
...sliding mobile phone 3docean business cellphone cellular communication detailed electronics ericsson gsm max mobile obj...
3d_ocean
$15
Apple iPad Air 2
...apple ipad air 2 3docean apple cellphone ipad ipad air ipad air 2 iphone smartphone tablet...
3d_ocean
$12
iPhone 4
...iphone 4 3docean apple apple philosophy beautiful cellphone clean great design iphone iphone 3g iphone 4 minimalistic...