Thingiverse
![LED Strip Corners (WS2812B) by drwatson6](/previews/8366721.jpg)
LED Strip Corners (WS2812B) by drwatson6
by Thingiverse
Last crawled date: 3 years, 2 months ago
From inspiration from others on here.
I needed a corner that could handle the 18ga wire I had on hand.
My method was measure the length of wire needed (silicone cover wire is best as it won't melt as easily).
-Red 38mm.
-Green 34mm
-White 30mm
Remove about 3mm off the tips.
Tin all the tips
Tin the three pads on the strip
Tape the strip down.
Heat the pad and the wire separately
Bring the two together and touch the wire to the pad and the iron all at the same time until they all melt together.
Use multimeter to ensure no solder is causing cross-connections.
Bend the wires into the print.
Use the strip adhesive to connect it to the tips of the print.
Tin the strip
(The wires should have already been tinned)
Tape down the two strips and the corner piece.
Line everything up
Solder the last three connections using the same method as above.
No glue required for the cover. They just snap in place.
I used PETG because it's a little more heat resistant for soldering on. It's also a little more flexible.
Good luck!
I needed a corner that could handle the 18ga wire I had on hand.
My method was measure the length of wire needed (silicone cover wire is best as it won't melt as easily).
-Red 38mm.
-Green 34mm
-White 30mm
Remove about 3mm off the tips.
Tin all the tips
Tin the three pads on the strip
Tape the strip down.
Heat the pad and the wire separately
Bring the two together and touch the wire to the pad and the iron all at the same time until they all melt together.
Use multimeter to ensure no solder is causing cross-connections.
Bend the wires into the print.
Use the strip adhesive to connect it to the tips of the print.
Tin the strip
(The wires should have already been tinned)
Tape down the two strips and the corner piece.
Line everything up
Solder the last three connections using the same method as above.
No glue required for the cover. They just snap in place.
I used PETG because it's a little more heat resistant for soldering on. It's also a little more flexible.
Good luck!
Similar models
thingiverse
free
![LED strips tool by vomestein](/t/8879021.jpg)
LED strips tool by vomestein
...i forgot to mention that i put a little square piece of plywood and covered it with a piece of aluminum tape to isolate the heat.
thingiverse
free
![50 watt COB LED wafer cover](/t/4681575.jpg)
50 watt COB LED wafer cover
...diation cooling.
the second file has a little more of a pocket for the nuts so that the cover pushes back closer to the heatsink.
thingiverse
free
![Tape Measure Yagi for T-Hunting by edbarnes](/t/8591607.jpg)
Tape Measure Yagi for T-Hunting by edbarnes
...m cheapo tradition, these parts were designed for the harbor freight free-with-purchase coupon 25 foot tape measure. enjoy! wa6ed
thingiverse
free
![Cable Solder-Help by TheKiter](/t/9693597.jpg)
Cable Solder-Help by TheKiter
...sts of two parts, so i can use the base to just tin my cables and all together to connect them.
i added some roundings and phases
thingiverse
free
![Neopixel Strip Friction Fitting by ScottCher](/t/8906303.jpg)
Neopixel Strip Friction Fitting by ScottCher
...astic to provide a nice tension fitting that's just tight enough to hold the wires against the neopixel strip's contacts.
thingiverse
free
![50mm 12v LED Tape Light Enclosure by BalinTech](/t/8588819.jpg)
50mm 12v LED Tape Light Enclosure by BalinTech
...e incorporating this design into a release version of the code, a thingiverse customizer and other designs which are forthcoming.
thingiverse
free
![A8 Heat bed Solder Support by Radem](/t/8805102.jpg)
A8 Heat bed Solder Support by Radem
...or and supports the connection. i attached it to the the acrylic frame with 2 sided tape, then attached the wires with a zip tie.
thingiverse
free
![Soldering Wire Holder by Lucan07](/t/8893795.jpg)
Soldering Wire Holder by Lucan07
...ob easier with this simple little stand to hold wires together for soldering slide over some heat shrink and the jobs a good one.
thingiverse
free
![Solder Pads by Sumner](/t/9694230.jpg)
Solder Pads by Sumner
...55.html
more on other items for your model railroad layout here ....
http://1fatgmc.com/railroad/3d-printer/3d-printer-index.html
thingiverse
free
![Silicone Heat Bed Mount by clough42](/t/8877249.jpg)
Silicone Heat Bed Mount by clough42
...r configured correctly. it's very easy to reach very high temperatures (>150c) very quickly if you have it misconfigured.
Drwatson6
thingiverse
free
![Lutron Dimmer Switch Knob by drwatson6](/t/8524504.jpg)
Lutron Dimmer Switch Knob by drwatson6
...ldn't find a replacement knob in white. my only choices were to buy a new switch with a white knob or make a replacement one.
thingiverse
free
![Flexible Magnetic Strip Insert Holder by drwatson6](/t/8654341.jpg)
Flexible Magnetic Strip Insert Holder by drwatson6
...#39;s for is one of those shower door kinds like this:https://www.amazon.com/flexible-magnetic-insert-framed-shower/dp/b00k318dj6
thingiverse
free
![2020 extrusion tall feet (printer foot) by drwatson6](/t/8666817.jpg)
2020 extrusion tall feet (printer foot) by drwatson6
...e. they are mirrors of each other so you can do all four corners.
i used these for my flsun i3 (2017 edition). they works great.
thingiverse
free
![Industrial lighting cage by drwatson6](/t/8526038.jpg)
Industrial lighting cage by drwatson6
...minimize supports. the bottom piece is upside down for the same reason. you will have to use supports.
hope you find this useful.
thingiverse
free
![Sonoff Basic toggle switch extension by drwatson6](/t/8242134.jpg)
Sonoff Basic toggle switch extension by drwatson6
...indicates the length of the gap between the sonoff toggle switch rod and the bottom of the switch pad. mine was 1.75mm different.
thingiverse
free
![Huawei Watch 2 Charging Stand by drwatson6](/t/8524673.jpg)
Huawei Watch 2 Charging Stand by drwatson6
...you've already downloaded it.
this stand doesn't work with the huawei watch 2 sport as it has a slightly different shape.
thingiverse
free
![Mozeat Wide Angle/Fish Eye/Macro Lens Mount by drwatson6](/t/8679475.jpg)
Mozeat Wide Angle/Fish Eye/Macro Lens Mount by drwatson6
... difficulty.
it is a small, complex piece, so i printed with very high quality settings so make sure all the detail is preserved.
thingiverse
free
![4010 long fan duct for E3D V6 Clone by drwatson6](/t/8671064.jpg)
4010 long fan duct for E3D V6 Clone by drwatson6
...nt to cinch it down.
i've included a measurement drawing so you can see if it will fit on your set up before printing.
enjoy.
thingiverse
free
![RAM 1500 Brake Release Fix by drwatson6](/t/8161473.jpg)
RAM 1500 Brake Release Fix by drwatson6
...lace the handle. here’s an example:https://www.youtube.com/watch?v=lgu5uvai65e
successful models tested on:
2012 ram 1500 laramie
Ws2812B
thingiverse
free
![WS2812B module by soswow](/t/8255737.jpg)
WS2812B module by soswow
...ws2812b module by soswow
thingiverse
ws2812b module (with sink) that you can buy from ebay/aliexpress etc
thingiverse
free
![wordclock ws2812b](/t/4709081.jpg)
wordclock ws2812b
...-40378401/
source code for this project can be found on my github pagehttps://github.com/alexstrassheim/wordclock-esp8266-ws2812b
thingiverse
free
![ws2812b bracket by DJMontage](/t/8790018.jpg)
ws2812b bracket by DJMontage
...et by djmontage
thingiverse
need to mount a few ws2812b rgb leds, using glue was not an option, but those small brackets wil do.
thingiverse
free
![Powerbox for WS2812B by Buddinski88](/t/8614103.jpg)
Powerbox for WS2812B by Buddinski88
...om a portable powerbox / powersupply for some ws2812b.
on my blog you can found a detailed buildlog with bom and everything else.
thingiverse
free
![LED Löthilfe WS2812B by Dixondsc](/t/8039616.jpg)
LED Löthilfe WS2812B by Dixondsc
...led löthilfe ws2812b by dixondsc
thingiverse
das ist eine löthilfe für die ws2812b einzeln leds
https://a.aliexpress.com/_b1envk
thingiverse
free
![WS2812B LED mounting kit by Kubulsch](/t/8095540.jpg)
WS2812B LED mounting kit by Kubulsch
... led mounting kit by kubulsch
thingiverse
set for attaching ws2812b leds to a table desk or other flat surface, stuck with tape.
thingiverse
free
![WS2812B LED for Lisam LS210 by Barneysp](/t/8709322.jpg)
WS2812B LED for Lisam LS210 by Barneysp
...pv-naze32-skyline32-flight-controller-p-1012950.html) support for lisam ls210 drone or any other drone with 30 mm spaced supports
thingiverse
free
![WS2812B LED mount by notthatbrad](/t/8629048.jpg)
WS2812B LED mount by notthatbrad
...ogether, and the channel underneath leaves room for the wires to pass through, so you can use as many, or as few, leds as needed.
thingiverse
free
![RGB LED HOLDER WS2812B & BUZZER MATEK by Bernd_S](/t/8870032.jpg)
RGB LED HOLDER WS2812B & BUZZER MATEK by Bernd_S
...rgb led holder ws2812b & buzzer matek by bernd_s
thingiverse
rgb led matek ws2812b holder for ls210 backside.
thingiverse
free
![WS2812B Tester by satininus](/t/8620890.jpg)
WS2812B Tester by satininus
... i install it. if the wires are run through the cap and spaced correctly, you should just have to lay the led on top to test it.
Strip
design_connected
$16
![Strip](/t/4567692.jpg)
Strip
...strip
designconnected
poliform strip chairs computer generated 3d model. designed by carlo colombo.
3ddd
free
![Strip Tease](/t/720856.jpg)
Strip Tease
...strip tease
3ddd
strip , tease
кресло strip tease
3d_export
$5
![stripping machine](/t/11888649.jpg)
stripping machine
...stripping machine
3dexport
stripping machine
3ddd
$1
![Casamania Strip](/t/973330.jpg)
Casamania Strip
...strip
стул casamania strip.
дизайнер: fabio novembre.
материал: полиэтилен.
размеры: ширина 59 см, глубина 62 см, высота 93,5 см.
design_connected
$16
![Strip leather](/t/4567710.jpg)
Strip leather
...strip leather
designconnected
poliform strip leather chairs computer generated 3d model. designed by carlo colombo.
design_connected
$4
![Strip Chair](/t/4565643.jpg)
Strip Chair
...strip chair
designconnected
castelijn strip chair chairs computer generated 3d model. designed by gijs bakker.
design_connected
$16
![Strip Chair](/t/4570108.jpg)
Strip Chair
...
designconnected
photo-realistic 3d models of the strip chair from henge for 3d architectural and interior design presentations.
3d_export
$5
![led strip](/t/11920402.jpg)
led strip
...led strip
3dexport
led strip modelled in inventor.<br>it includes .obj and .fbx model in real-world scale.
3ddd
$1
![Ванна aquamass strip](/t/797168.jpg)
Ванна aquamass strip
... ванна
http://www.aquamass.com/en/so-creative-so-design/strip/strip
в архиве есть файл 2011 версии
3ddd
free
![Strip Chair](/t/598927.jpg)
Strip Chair
...actured by poliform (www.poliform.it).
dimension in cm: 60w_57d_72h
uvw mapped, free texture folder.
file formats: fbx and obj.
Corners
archibase_planet
free
![Corner](/t/946338.jpg)
Corner
...corner
archibase planet
nook corner
corner n030708 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
![Corner](/t/947609.jpg)
Corner
...corner
archibase planet
corner post rack
fp corner wh - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3ddd
$1
![Country Corner](/t/920784.jpg)
Country Corner
...country corner , комод , прованс
country corner
3ddd
$1
![Corner 8140](/t/612342.jpg)
Corner 8140
... corner
corner 8140 - 16,5 x 17,4 (cm)
corner 8141 - 16,5 x 29,5 (cm)
corner 8142 - 16,5 x 41,5 (cm)
corner 8143 - 28 x 28 (cm)
archibase_planet
free
![Corner](/t/946781.jpg)
Corner
...corner
archibase planet
seat easy chair furniture
havanna corner - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3ddd
$1
![Country corner](/t/614205.jpg)
Country corner
... country corner , romance
рамка country corner, romance,
артикул cc0141
3ddd
$1
![Country corner](/t/920575.jpg)
Country corner
...country corner
3ddd
country corner , журнальный
country corner pbth размеры 169*69*49
3d_export
$5
![Corner](/t/11373793.jpg)
Corner
...corner
3dexport
3ddd
$1
![Table-Corner](/t/1002435.jpg)
Table-Corner
...table-corner
3ddd
круглый
table,corner
3ddd
$1
![Table,Corner](/t/1089485.jpg)
Table,Corner
...table,corner
3ddd
журнальный
table,corner
Led
3d_export
$5
![led](/t/11425881.jpg)
led
...led
3dexport
the led is cut with all the parts.
3ddd
$1
![Monacor / PARL56DMX / LED-320RGBW / LED-345RGBW / LED-300RGB](/t/612514.jpg)
Monacor / PARL56DMX / LED-320RGBW / LED-345RGBW / LED-300RGB
... прожектор
http://www.monacor.dk/
parl56dmx
led-320rgbw
led-345rgbw
led-300rgb
turbosquid
$10
![LED](/t/13317501.jpg)
LED
...led
turbosquid
free 3d model led for download as blend on turbosquid: 3d models for games, architecture, videos. (1691856)
3d_export
$5
![led lamp](/t/11423129.jpg)
led lamp
...led lamp
3dexport
led lamp, brightness animation
3ddd
free
![leds-c4](/t/815641.jpg)
leds-c4
...leds-c4
3ddd
leds-c4
современный торшер
3ddd
free
![leds-c4](/t/837451.jpg)
leds-c4
...leds-c4
3ddd
leds-c4
настольный лампа
turbosquid
$19
![LED](/t/13371517.jpg)
LED
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
![Led](/t/13237358.jpg)
Led
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
![LED](/t/13259706.jpg)
LED
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
![LED](/t/13391561.jpg)
LED
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.