Thingiverse
Lack Power Panel by gdave44
by Thingiverse
Last crawled date: 3 years ago
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
WARNING! Don't make this... yet.
This plan worked completely fine while printing PLA and heating the bed to 65'C. But, when I started printing PETG with a heat bed at 85'C, the resistance in the bolt was too much, warmed up the connector and melted the PLA. Thankfully, I noticed and avoided a short.
I'm currently awaiting banana plug hardware and will modify the setup to accomodate.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
After moving my power supply under my lack table and adding a cover with a power switch, I wanted an above-table disconnect for the printer as well as a real time volt meter for the power lines coming up through the table.
I simply used M4 bolts as the power studs and simple Chinese voltmeters for the displays.http://www.ebay.com/itm/391701932930
You may notice a 5V hole on the side. I'm working on adding a usb power connector on that side, but I'm working out exactly how I want to handle that.
WARNING! Don't make this... yet.
This plan worked completely fine while printing PLA and heating the bed to 65'C. But, when I started printing PETG with a heat bed at 85'C, the resistance in the bolt was too much, warmed up the connector and melted the PLA. Thankfully, I noticed and avoided a short.
I'm currently awaiting banana plug hardware and will modify the setup to accomodate.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
After moving my power supply under my lack table and adding a cover with a power switch, I wanted an above-table disconnect for the printer as well as a real time volt meter for the power lines coming up through the table.
I simply used M4 bolts as the power studs and simple Chinese voltmeters for the displays.http://www.ebay.com/itm/391701932930
You may notice a 5V hole on the side. I'm working on adding a usb power connector on that side, but I'm working out exactly how I want to handle that.
Similar models
thingiverse
free
Mendel XLR + Coax power connector bracket (parametric) by jridley
...a small, silent and nice looking "laptop replacement" power brick, which i connect via a standard coax power connector.
thingiverse
free
Bed cable chain and heater wiring connector bracket by demigh0d
...#39;t want to be heating the whole thing when i'm printing smaller parts. with this i am able to easily switch my print beds.
thingiverse
free
Printrbot LC+ Heated Bed Clips Side & Front by PacificBlue
... flat as it heated up so i made these clips to help flatten it by clamping the edges. it took four side clips and one front clip.
thingiverse
free
RepRap power expander housing by CoenJ
...ture just after bolting it on the printer, don't pay attention at the mess (trying some upgrades).
bill of materials attached
thingiverse
free
Power Supply Bracket by SgtWoody
...iverse
simple mounting bracket i designed to support my power supply under my ikea lack table. printed with 10% infill with pla.
thingiverse
free
Lack Connector (no screws) by the3der
...r (no screws) by the3der
thingiverse
i just wanted to connect lack side tables without screws. this one does it rather securely.
thingiverse
free
Power Supply Mounting Brackets by freakinhuge
...kets i came up with to do just that.
these were designed in autocad 2011.
printed in black abs on my prusa mendel w/ heated bed.
thingiverse
free
IKEA Lack headphone holder by mrblaha
...i've designed this holder. just slide it onto the side. added a small hole for screw if it won't fit tight on your table.
thingiverse
free
drain sieve - Abflusssieb by Thosa
... sided carpet tape for better adhesion.
bed temperature during printing 40°c.
after printing, heat up to 60°c for easier removal.
thingiverse
free
brio wooden rails female to female connector with one permanent side by ImShogun
...his printed rails, but that they lack 1.5mm to also work with "regular wooden tracks". this is his, 1.5mm added length.
Lack
thingiverse
free
STACK-A-LACK by jangrewe
...oublestack-a-lack plates.
the rack-a-stack-a-lack plate contains the adapters for all four corner and the two middle connectors.
thingiverse
free
To raise your LACK box with 2 LACK tables by RugbyGoth
...k box with 2 lack tables by rugbygoth
thingiverse
just a little thing to be able to raise your lack box with an other lack table
thingiverse
free
Lack Stacker by Ivysore
...firmly in place so that it cannot slide off of whatever it is set onto. does not prevent the lack from being lifted out of place.
thingiverse
free
Ikea Lack Verbinder / Joiner
...ikea lack tischverbinder, zum verbinden zweier ikea lack tische.
ikea lack table connector, for connecting two ikea lack tables.
thingiverse
free
Lack Grommet
...lack grommet
thingiverse
metric - 50 mm.
thingiverse
free
Lack table foot
...lack table foot
thingiverse
four of these are required for fixing one lack table on top of another
thingiverse
free
Loquet Lack by Clement_Fasquel
...loquet lack by clement_fasquel
thingiverse
loquet pour caisson lack
https://www.youtube.com/watch?v=ffvl5cv8_cw
thingiverse
free
IKEA LACK FEET
...ikea lack feet
thingiverse
hey,
this is a simple feet for ikea lack table. fits perfect ;-)!
greetings
thingiverse
free
LACK - Filament by HengNing90
...lack - filament by hengning90
thingiverse
just screw it through your ikea-lack-table and put the filament through
thingiverse
free
Lack Table stacker
...lack table stacker
thingiverse
to stack two lack tables. made one with and one without holes for a screw.
Panel
thingiverse
free
Shower panel panels hook by Mikifly
...shower panel panels hook by mikifly
thingiverse
shower panel panels hook
thingiverse
free
Arcade panel
...arcade panel
thingiverse
a simple arcade panel.
thingiverse
free
Control panel
...control panel
thingiverse
control panel for scuba regulator/bank system
thingiverse
free
Solar panel
...solar panel
thingiverse
it is a full-size solar panel.
you have to print at 5%.
thingiverse
free
Nuclear panel
...nuclear panel
thingiverse
this is a nuclear panel created for the fun !
don't forget to enable the support.
thingiverse
free
clips panel
...lips panel
thingiverse
this is a clip that i made for folding mini asian panel / screenhttps://www.thingiverse.com/thing:2573850
thingiverse
free
Panel Mounts by valentinp72
...panel mounts by valentinp72
thingiverse
some xt60 and usb b panel mounts.
designed to be glued on the panel.
thingiverse
free
M3D Panels by steve3d
...m3d panels by steve3d
thingiverse
m3d enclosure
lateral panels are fixed;
front and rear panels are removable.
thingiverse
free
v3 Panel by SpencerR87
...v3 panel by spencerr87
thingiverse
v3 panel
thingiverse
free
Decorative Panel by ashimizu
...decorative panel by ashimizu
thingiverse
decorative panel.
Power
thingiverse
free
Power Macintosh Power PC Power Button (Repaired) by 360alaska
...power macintosh power pc power button (repaired) by 360alaska
thingiverse
repaired the power button
thingiverse
free
Power adaptation for switching power by vladimirgaal
...tation with switch to be used directly on switching power supply.
be sure that this part is compatible with your switching power.
thingiverse
free
power jack
...power jack
thingiverse
iec ac jack power
thingiverse
free
POWER SUPLY HIDE POWER SWITCH by Thearc
...power suply hide power switch by thearc
thingiverse
hello ! i made this power switch for my new power suply
work really well
thingiverse
free
Power supply & power button support by thomasgobert
...power supply & power button support by thomasgobert
thingiverse
needed !
thingiverse
free
Power Bank Box for Power Bank with light by 344026653
...power bank box for power bank with light by 344026653
thingiverse
this is where the power bank parts are kept in.
thingiverse
free
Power Macintosh Power PC Power Botton ;) by Rattiso
...stic, pegt not yet tested, should be even more durable than pla
better before installing, glue
the power button to the holder !!!
thingiverse
free
Power Switch and Power Plug Angle Brackets by EvolHub
...brackets
power switch bracket hole is designed for "carling ra901/911t85" switch, but should fit similar size switches.
thingiverse
free
flower power by Syzguru11
...flower power by syzguru11
thingiverse
flower power
thingiverse
free
flower power by Syzguru11
...flower power by syzguru11
thingiverse
flower power