Thingiverse
Junsi iCharger 4010 DUO Case (incl. PSU) by MarenB
by Thingiverse
Last crawled date: 3 years ago
This project is still in progress. Sorry for the bad photos, i shall update them at a later stage.
Recently, I discovered how well my iCharger 401 DUO fitted into the beauty case I used for my groundstation project.
So I bought another one to install my charger and its power supply into it to have a protective case that I can carry easily to the flying field.
The PSU is based on two HP DPS-1200FB A units that were supposed to fire IT servers. To connect them in series requires some modification on one of the units, something I will not describe here and what should only be done by experts (google will give you more information).
I noticed, that the cheap beauty cases are not very precise in their measurments, I have two and they differ up to 12mm in each direction. So designed the brackets for the PSUs in the lower compartment with floating bushes to compensate a few milimeters of width.
The deck plate was made out of 6mm plywood, you might need to remix this based on your actual size needed. It has an opening to install a connector into it. This is foressen for a panel-mount version of an EC5-connector, as that is what the charger comes with. I still have to draw this component.
The bezels are designed to be installed in the small sides of the lower compartment, their inserts feature ventilation grills and a cut-out for a C14-connector incl. fuse and switch to connect a power cord on one side. (I used this one: https://www.conrad.de/de/kaltgeraete-steckverbinder-c14-stecker-einbau-vertikal-gesamtpolzahl-3-10-a-schwarz-1-st-501638.html)
UPDATE 16/01/2016: added the EC5 wallmount connector to get power from the PSUs through the cover plate. I didn't print it yet, so if one is brave enough to give it atry, let me know the results, please :)
UPDATE 28/01/2016: after relatively short time at the first test run of the fully assembled case, the fans inside the PSUs were running on full speed and their metal housings had more than 50°C - while the charger was still idling! So I decided to modify the grills in order to improve the ventilation. A small drawback is that's now possible to look through them...
Recently, I discovered how well my iCharger 401 DUO fitted into the beauty case I used for my groundstation project.
So I bought another one to install my charger and its power supply into it to have a protective case that I can carry easily to the flying field.
The PSU is based on two HP DPS-1200FB A units that were supposed to fire IT servers. To connect them in series requires some modification on one of the units, something I will not describe here and what should only be done by experts (google will give you more information).
I noticed, that the cheap beauty cases are not very precise in their measurments, I have two and they differ up to 12mm in each direction. So designed the brackets for the PSUs in the lower compartment with floating bushes to compensate a few milimeters of width.
The deck plate was made out of 6mm plywood, you might need to remix this based on your actual size needed. It has an opening to install a connector into it. This is foressen for a panel-mount version of an EC5-connector, as that is what the charger comes with. I still have to draw this component.
The bezels are designed to be installed in the small sides of the lower compartment, their inserts feature ventilation grills and a cut-out for a C14-connector incl. fuse and switch to connect a power cord on one side. (I used this one: https://www.conrad.de/de/kaltgeraete-steckverbinder-c14-stecker-einbau-vertikal-gesamtpolzahl-3-10-a-schwarz-1-st-501638.html)
UPDATE 16/01/2016: added the EC5 wallmount connector to get power from the PSUs through the cover plate. I didn't print it yet, so if one is brave enough to give it atry, let me know the results, please :)
UPDATE 28/01/2016: after relatively short time at the first test run of the fully assembled case, the fans inside the PSUs were running on full speed and their metal housings had more than 50°C - while the charger was still idling! So I decided to modify the grills in order to improve the ventilation. A small drawback is that's now possible to look through them...
Similar models
thingiverse
free
Compartment/Case/Box for Power socket C13/C14 / Kaltgerätebuchse-Dose by thingster
...mpartment box for standard c13/c14 power sockets.
requirements:
brass inserts for m4 screws
m4x20 or so screws
no support needed.
thingiverse
free
DPS-800GBa mounting Brackets
...ector and 1 jst rcy connector for the power switch.
i use them to power my other projecthttps://www.thingiverse.com/thing:3988814
thingiverse
free
Portable USB lipo charger by GeorgeFPV
...ith freecad. i have also updated the 3d design files if you want to modify them. i you print and have sucess let me now please ;)
thingiverse
free
Ender 2 power supply case by Smirre77
...design. i made it a little larger with cutouts for an xt30 connector and this power connector. i also added mounts for m3 screws.
thingiverse
free
Ender 4 PSU Switch by donminca
...e cables behind the power supply plate in the 4020 slot.
to screw it i used 2x m4 x 10 with t-nuts always found here on the site.
thingiverse
free
Amiga PicoPSU Case by Lemaru
.... one has the amiga text on and the other is blank.
update: as requested i have now uploaded the step files for anyone to modify.
thingiverse
free
Meanwell PSU Rear Cover for Noctua Fan by Bladevane
... pcb. i have also included a cover for the fan in case users want it to blow into the psu rather than extract air out of the psu.
thingiverse
free
ATX PSU Inverting Adapter by NXSLogan
...of situation, then hopefully this helps you as much it has helped me.
instructions: screw plate onto psu, then install into case.
thingiverse
free
EC5 Connector to IEC Cutout Pico PSU 12v by robertmaks
...overkill; the whole point is to make a reliable and somewhat trip over a cord and not get pulled out of the connector kinda deal.
thingiverse
free
Expanded PSU Top Cover
...n the original so i designed this replacement top plate for my psu so that it would have the appropriate amount of top clearance.
Junsi
thingiverse
free
Junsi CB1010 Balancer-Boardholder by mawi86
...junsi cb1010 balancer-boardholder by mawi86
thingiverse
holder for junsi cb1010 balancerboard
thingiverse
free
Junsi 106b+ - XT60 conversion by ebastler
...s after closing it. fits my junsi perfectly, but they seem to have quite large tolerances. tell me if you encounter any problems.
thingiverse
free
Junsi 4010 Screen Protector by ScorpionTDL
...ntrol knob and the interior of my bag.
the protector is designed to prevent the bag pressing continuously on the screen and knob.
thingiverse
free
Junsi X8 Charger Box by haramon
... part to test the slider. it works :)
so, if you will print it - try. if you want to have the fusion360 files, please
contact me.
thingiverse
free
Junsi X8 Charger Box by haramon
... part to test the slider. it works :)
so, if you will print it - try. if you want to have the fusion360 files, please
contact me.
Icharger
thingiverse
free
icharger x8 holder by cturna
...icharger x8 holder by cturna
thingiverse
remixed icharger x6 stand for x8
thingiverse
free
iCharger X6 BigButton Upgrade
...icharger x6 bigbutton upgrade
thingiverse
bigger button for the original icharger x6 (with the small buttonwheel)!
thingiverse
free
iCharger 406 Support by mdrjr
...icharger 406 support by mdrjr
thingiverse
quick and dirt icharger 406 duo side support for mounting on a wood base.
thingiverse
free
Icharger X6 holder by Tbamsey
...icharger x6 holder by tbamsey
thingiverse
simple icharger x6 base velcro to power supply printed in pla 203/50
thingiverse
free
iCharge-Case by Zannddor
...emperature 190
no raft
no support
"infilldensity": 15%,
"numberofshells": 2,
"layerheight": 0.2025,
thingiverse
free
Dual iCharger X6 Holder
...or race day bench
no adhesive necessary
breaks down for easy transport
get the "icharger x6" on amazon by clicking here
thingiverse
free
iCharge Case 2 by Zannddor
...
temperature 190
no raft
no support
"infilldensity": 20%,
"numberofshells": 2,
"layerheight": 01.5,
thingiverse
free
ICharger Stand basic by Tbamsey
...or more infill to keep parts from warping from heat. petg i use 25% infill no warping. i use 5mm brim on braces printed on glass.
thingiverse
free
iCharger 206B Mounting Bracket by PowerScissor
...e attached the small rubber pads/feet to the bottom, so if you didn't put them on the bracket most likely won't fit snug.
thingiverse
free
iCharger 4010 DUO mounts by jesi
...by jesi
thingiverse
just a bit modified arms and longer "claws".
remix from: https://www.thingiverse.com/thing:1259810
Marenb
thingiverse
free
Hump for S800 Reptile Canopy by MarenB
...th cutout 45x75mm. it allows the fitment of 4x 18650 liion cells in a 2x2 formation.
thanks a lot, syco, for the special variant!
thingiverse
free
Runcam 2 HD to GoPro Mount Adapter SHORT by MarenB
...thingiverse
daniel's adapter works great, but it was a little too long for my purpose, so i designed an 8mm shorter variant.
thingiverse
free
Cradle for Mini APM Pro by MarenB
...aircraft permanently and holds the apm precisely in a defined reference positon. the apm is fixed in the cradle with a cable tie.
thingiverse
free
Dragonlink V3 Cradle for FrSky Taranis X9E by MarenB
... as well? can't try by myself) to a frsky taranis x9e.
just put it inside the taranis' handle and drop the tx into, done!
thingiverse
free
Antennatube holder for S800 Reptile SkyShadow by MarenB
...ngle.
2017/02/19:
i noticed that antenna tubes seem to be 1/8" rather than 3mm.
updated the stl file with enlarged diameter.
thingiverse
free
Quanum Trifecta battery holder by MarenB
...the rear.
fixation is much better now, could probably do flips and more acro stuff without being afraid of loosing the battery :)
thingiverse
free
Sideplates for AMAX H3 and Runcam Micro Swift by MarenB
...ent tilt angle, hence i designed my own ones.
they feature a fixed 25° tilt angle, let me know, in case you prefer anything else!
thingiverse
free
FPV Backpack for PZ0420m by MarenB
...nd you fix the backpack with m4 bolts through those wholes.
i printed mine from petg with an infill of 10%. it weights about 18g.
thingiverse
free
Dust port / shop vac adaptor for miter saw ELU PS174/PS274, DeWalt DW700 and others by MarenB
...e center section of an elu or dewalt miter saw to a shop vac or dust collector system. it fits to hoses with 32mm inner diameter.
thingiverse
free
Runcam 2 HD Brushless Gimbal Mount by MarenB
...hout camera battery.
you'll need two short (thread length ~5-6mm) m2,5 bolts w/ countersunk heads to bolt the parts together.
4010
turbosquid
$2
passenger train 4010
...oyalty free 3d model passenger train 4010 for download as obj on turbosquid: 3d models for games, architecture, videos. (1708115)
3ddd
$1
Люстра Masiero Glasse 4010
...ериал: ткань, металл, хрусталь
цвет арматуры: слоновая кость
офсайт:http://www.masierogroup.com/en/classica/4010/family
3ddd
$1
Masiero classica 4010/A2
...masiero classica 4010/a2
3ddd
masiero
высота: 40 см
ширина: 40 cм
глубина: 25 см
3ddd
$1
Бра Glasse 4010 A3 P01
...ериал: ткань, металл, хрусталь
цвет арматуры: слоновая кость
офсайт:http://www.masierogroup.com/en/classica/4010/family
3ddd
$1
Торшер Masiero GLASSE 4010 STL3 P01
...ериал: ткань, металл, хрусталь
цвет арматуры: слоновая кость
офсайт:http://www.masierogroup.com/en/classica/4010/family
3ddd
$1
Люстра Masiero Glasse 4010 PL8 P01
... g9
материал: металл, хрусталь
цвет арматуры: слоновая кость
офсайт:http://www.masierogroup.com/en/classica/4010/family
3ddd
$1
Бра Masiero Glasse 4010 A2+1 P01
...ериал: ткань, металл, хрусталь
цвет арматуры: слоновая кость
офсайт:http://www.masierogroup.com/en/classica/4010/family
3ddd
$1
Настольная лампа Masiero GLASSE TL3 P01
...e14 материал: ткань, металл, хрусталь цвет арматуры: слоновая кость офсайт:http://www.masierogroup.com/en/classica/4010family ...
3ddd
$1
Stanislav Katz
...material: painted mdf, polyurethane. color: black (ral-9005) / pink (ral-4010 dimensions: 215 x 110 x 50...
3d_export
$20
CDJ 800 MK2 Eqiupment for dj 3D Model
....max .obj .fbx .ma .lwo .3ds .3dm .stl godzik 4010 ...
Incl
3d_export
$6
chair with armrest cheerio incl cushion
...chair with armrest cheerio incl cushion
3dexport
chair with armrest cheerio incl. cushion kare design
cg_studio
$20
occhio sento - IES incl.3d model
...el
cgstudio
.3ds .c4d .obj - occhio sento - ies incl. 3d model, royalty free license available, instant download after purchase.
turbosquid
$2
Chair incl room modern seat furniture
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Lowpoly & Cheap - GrandPiano (texture & materials incl)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
cg_studio
$49
FSC All-in-One Card Reader incl. Cards3d model
...gstudio
.max - fsc all-in-one card reader incl. cards 3d model, royalty free license available, instant download after purchase.
cg_studio
$39
FSC Wireless USB Laserpointer incl. USB Stick3d model
...
.max - fsc wireless usb laserpointer incl. usb stick 3d model, royalty free license available, instant download after purchase.
3d_ocean
$25
miMac Pack incl. Computer Screen, Mouse and Keyboard
...nd accurate model of the apple imac, ready for render in any scene and perfect for close-uü as well as far-away shots. all lay...
3ddd
$1
Диван ZOOM IN by MONTIS
...montis , zoom in breedte: 175 cm (220 cm incl armleuningen) diepte: 59 cm (95 cm incl. rugleuning) hoogte:...
3ddd
free
Eichholtz Presidental S
...eichholtz presidental s 3ddd eichholtz , presidental nickel finish incl shades d-450mm...
3ddd
$1
BoConceptLamp_Tulip
...3ddd boconcept , tulip boconceptlamp_tulip 3ds max 2008, vray incl .obj file and textures in max...
Duo
design_connected
$13
Duo
...duo
designconnected
boconcept duo computer generated 3d model.
design_connected
$13
Duo
...duo
designconnected
anglepoise duo computer generated 3d model. designed by carwardine, george.
design_connected
$13
Duo Bench
...duo bench
designconnected
forms+surfaces duo bench computer generated 3d model.
3ddd
free
Hoesh / SingleBath Duo
... tara.logic , ванна
ванная hoesch singlebath duo со смесителем tara.logic
3ddd
$1
Harvia 20 Duo
...d
harvia , каменка , печь
каменка harvia 20 duo
3ddd
free
Cappellini Duo
...same flower, that passes through both vessels, manifests itself as the only sincere means of connection between the two elements.
3ddd
$1
Plastics Duo
...plastics duo
3ddd
kartell , модульный
kartell
turbosquid
$1
cama duo
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
INCANTO Duo
... металлические подлокотники с обитыми накладками (модификация soft), металлическую раму. столешницы столиков выполнены из стекла.
3ddd
$1
Anglepoise Duo Table Lamp
...anglepoise duo table lamp
3ddd
anglepoise duo table lamp
Psu
3d_ocean
$17
Computer Case
...3docean atx case computer corsair full game gaming pc psu full tower-like computer case model with 113946...
cg_studio
$9
Power Supply Unit PSU3d model
...d .fbx .lwo .ma .max .obj .xsi - power supply unit psu 3d model, royalty free license available, instant download after purchase.
thingiverse
free
PSU cover for 12v 30A PSU by Salti
...
cover for the "dangerous" end of a standard led psu
230v input, 2 x 12v outputs
supports psu width 11cm and height 5cm
thingiverse
free
psu holder by sta8atos
...psu holder by sta8atos
thingiverse
psu holder
thingiverse
free
psu stamp by astorck
...psu stamp by astorck
thingiverse
psu stamp
thingiverse
free
PSU Cover by Shojo
...psu cover by shojo
thingiverse
psu cover
thingiverse
free
PSU cover by chroja
...psu cover by chroja
thingiverse
psu cover
thingiverse
free
PSU Cover for 9,9 cm PSU Anet A8 by Wolverine_DH
...a8 by wolverine_dh
thingiverse
psu cover for 9.9sm psu optimal high for anet a8 screw holes, more side holes for diffrend psus.
thingiverse
free
Anet A8 PSU Fan (2017 PSU)
...coarse threaded fan screws. additionally 2 x m3x8mm machine screws needed to attach fan mount to psu. do not use long than 8mm.
thingiverse
free
SFX PSU to ATX PSU adapter by Kanashii
... atx format adapter so i made my own adapter. better use hard plastic to stick psu to pc's case without breaking the adapter.
Case
3d_export
$1
case
...case
3dexport
case
archibase_planet
free
Case
...case
archibase planet
showcase show-case glass case
glass-case + cakes - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
showcase show-case glass case
glass-case for chips - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case shelving drawer
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case rack locker
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case drawer kitchen furniture
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case cupboard shelving
glass case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case handbag suitcase
case - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case suitcase
case 5 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
locker case dresser
case - 3d model (*.gsm+*.3ds) for interior 3d visualization.