Thingiverse
Jabba's Palace and Rancor Pit Playset - scaled for Playskool Galactic Heroes by mpeeples2008
by Thingiverse
Last crawled date: 3 years, 4 months ago
My son got a used set of Star Wars Galactic Heroes figures on eBay featuring the Jabba's Palace characters. He wanted a playset to use with them and we took that as an opportunity to learn a bunch of new modeling and printing skills. The complete playset is made of a combination of plywood, bass wood, and 3d printed parts. Most of the detailed parts are 3d printed. I have included a model of all of the parts assembled so it should be relatively easy to see where things go but I also will include some detailed notes on the construction here. There are likely a few things that I would improve if I were starting from scratch now and I'll note that below as well.
The build
Building the box/Rancor pit
The first basic step is to build the box for the Rancor pit and base of the model. I designed this to be built from a single 24"x24" piece of plywood with little waste. The box itself is 16"x12" and 8" high with no front or top. I've included a cut list that shows how you can do this without waste. The remaining 8"x8" piece will be used in a later step. None of the tolerances are so tight that you need to worry too much about blade width. For the top of the box, I used some scrap 1x2 wood to line the top on all four sides leaving a gap in the middle for the trap door. I assembled the box with glue and temporary shims and clamped it without much trouble. It helps to sand and paint it at this stage.
Building the main floor
To make the main floor of Jabba's Palace, I used 4 2mm thick basswood sheets (20cm x 30 cm) that I had lying around. I glued the sheets together and clamped them using wood glue and clamps to create a single surface that was 40x30cm and two sheets (4mm) thick. I then cut a 10x6cm hole for the trap door (see full model for specific location). This piece will eventually be set on the box built in the last step on top of the 1x2" boards so do a test fit here and trim as necessary.
3D printed parts
To make the model exactly has I have it you will need to print all of the parts I have above along with a couple of parts from other Thingiverse projects. You will need to print six of the 90 degree angle pieces, two of the "Jabba spit cooker" pieces and will need to print two of the "Jabba side wall - reversible" pieces with one mirrored in the horizontal dimension. All of these parts except the Jabba table, the Jabba Palace floor switch, and the Rancor door switch and hinge print fine with no supports. I would suggest printing the small parts at 0.12 resolution. Depending on the size of your printer bed, you may need to print the pieces labelled Jabba back wall and Jabba middle wall in two pieces and then glue them together (I ended up doing this and gluing them with super glue).
Other parts you will need are the Throne Rail by LukeSkyPilot, the Jabba's Rancor posable figure by Geoffro, and the face from the Resculpted Rancor by Daylightinventor. The Throne Rail will need to be resized a bit but the others should be printed at 100% and will be fine.
Most of these 3D parts were designed by me from scratch but a few used elements of other projects. Specifically, the trap door used the OpenForge 2.0 grate along with the reversible hinge by andyosier together, the Rancor door hinge is based on a design by Braunbaer, and the fire on the roasting table is simply the wall of fire by Talismancer resized.
Detail work and Assembly
There are a few very detailed things that need to be done to finish specific pieces described here.
The trap door:
To complete the trap door, test fit it into the hole you cut in the main floor and widen the hole if necessary so the trap door fits snugly but doesn't get caught on the edges of the hole. Fit the "Jabba's Palace Floor Cover" on top of this and make sure all clearances are good. Once you are satisfied, use superglue to attach the Floor Cover to the trap door (you will want to paint the trap door first).
Here is the trap door in action:
The roasting table:
In ROTJ there is a doner spit roast thingy behind Jabba's throne. To make this, take the 3d printed table and attach the two printed spit roast parts with the holes aligned with the long dimension of the table at least 15 mm apart (again, I would paint all of these pieces first). For the spit roast turning thing I used a nozzle cleaner wire that comes with an Ender 3 and stuck it through the holes in the roaster, bent it, and cut it to size using flush cutters. Once I was happy with this, I put some putty around the wire to simulate whatever alien meat was cooking and then painted it once it was dry. Finally, I glued the painted fire in the middle and did some touch up and details on the painted table with a fine point marker.
Jabba's throne:
Once you have printed and painted the main throne, the throne railing, the hookah and base piece and painted all of those, you are ready to assemble them. I did this using super glue without too much trouble. The only thing to be careful on is that you have the throne railing sized so that the flat portion where the hookah and frog creature bowl thing goes are about 15mm across. I glued the throne in place but if you want to make it slide forward like it does in the movie, you could print a rail or something. This is probably what I would have done if I'd remembered that the real trap door is not the fancy grated floor but in front of that.
Assembling the walls:
Check the overall model for wall placement. The way I did this was to glue the back wall cover to the back wall and glue the assembled part to the Jabba's throne stairs piece. none of these really need to be painted first if you plan on using a spray primer or something. Next, I glued two 90 degree angle pieces to the middle wall and glued that to the main floor surface using super glue. I then glued the two side walls to the floor using two 90 degree angle pieces on each and then glued them to the corner of the middle wall all with super glue.
Completing the main floor:
Before doing the next steps, it makes sense to prime and paint the entire floor and wall assembly. After you're happy with that, glue the mounted rancor head to the desired side wall, glue the Han solo in carbonite stand in place, glue the throne in place if desired, and finally glue the trap door hinges to the underside of the main floor in the appropriate spot making sure you have a fit that allows the door to freely fall. After this, use a 1/4 drill bit to drill a hole for the "Jabba's Palace floor switch." Fit the bigger piece on the top of the floor and then use a M3x20 screw through that and attach the bottom piece using a M3 nut so that the entire assembly can be rotated and the arm on the underside can "latch" the trap door shut. I found it helpful to paint a line on the main floor and the rotating piece on the top that marks the position when the door is shut.
Rancor pit and door:
For the Rancor pit you need one Rancor and I've linked to the model I used above. It also helps to have a lot of bones. I just found some 3d models of a bunch of random Pleistocene megafauna and printed them at appropriate scales. The complicated part is the door. To assemble this door print the parts labled "Rancor pit door," "Rancor pit brace and slots," and "Rancor door switch and hinge". Also, cut the remaining bit of plywood to 13cm x about 20cm. Fit the rancor pit braces with the three slots into the base brace (the piece shaped roughly like a dumbbell with holes in each end with the side with one slot exposed fit into the hole. I found it necessary to glue a second brace to the top of the door to keep the side braces from moving (I did this by simply printing and gluing a second bottom brace to the back of the upright arms). Take the piece that will be the bottom of the door and drill holes for M3 hardware to go through (I used M3x10 but shorter would work too). Place screw through the holes and attach nuts on the back side. When you are doing this, attach the two small pieces that printed with the pit brace and slots to the outer screws with the arms facing outward on each side (these are handles to help you lift). Fit the doors through the slots in the upright arms and test the motion. If all looks good, paint them and then reassemble. Finally, once you've got all of this working, glue the whole thing to the piece of plywood you cut earlier. Fit this assembly in the plywood box on either the right or left side. Lift the doors as high as you would like them to go and then test fit the "Rancor pit hinge and button" on the corner as shown in the pictures above. Mark the holes for this hing and attach it to the plywood box using M2 nuts and bolts. Once you're happy with the position of everything, glue the entire door assembly into the box using wood glue and you're done.
Here is a video of the door in action
Final thoughts
If I were doing this again, I probably wouldn't do it exactly the same way. I ended up modifying a few parts on the fly and tried to reflect that in the final models presented here but I didn't initially create this to be recreated by others (but some asked for this write-up). Have fun with it and make any modifications and let me know if you have any issues. This is perfectly sized to use with the Galactic Heroes Playskool figures but there are also plenty of models on Thingiverse that could be printed and used instead.
The build
Building the box/Rancor pit
The first basic step is to build the box for the Rancor pit and base of the model. I designed this to be built from a single 24"x24" piece of plywood with little waste. The box itself is 16"x12" and 8" high with no front or top. I've included a cut list that shows how you can do this without waste. The remaining 8"x8" piece will be used in a later step. None of the tolerances are so tight that you need to worry too much about blade width. For the top of the box, I used some scrap 1x2 wood to line the top on all four sides leaving a gap in the middle for the trap door. I assembled the box with glue and temporary shims and clamped it without much trouble. It helps to sand and paint it at this stage.
Building the main floor
To make the main floor of Jabba's Palace, I used 4 2mm thick basswood sheets (20cm x 30 cm) that I had lying around. I glued the sheets together and clamped them using wood glue and clamps to create a single surface that was 40x30cm and two sheets (4mm) thick. I then cut a 10x6cm hole for the trap door (see full model for specific location). This piece will eventually be set on the box built in the last step on top of the 1x2" boards so do a test fit here and trim as necessary.
3D printed parts
To make the model exactly has I have it you will need to print all of the parts I have above along with a couple of parts from other Thingiverse projects. You will need to print six of the 90 degree angle pieces, two of the "Jabba spit cooker" pieces and will need to print two of the "Jabba side wall - reversible" pieces with one mirrored in the horizontal dimension. All of these parts except the Jabba table, the Jabba Palace floor switch, and the Rancor door switch and hinge print fine with no supports. I would suggest printing the small parts at 0.12 resolution. Depending on the size of your printer bed, you may need to print the pieces labelled Jabba back wall and Jabba middle wall in two pieces and then glue them together (I ended up doing this and gluing them with super glue).
Other parts you will need are the Throne Rail by LukeSkyPilot, the Jabba's Rancor posable figure by Geoffro, and the face from the Resculpted Rancor by Daylightinventor. The Throne Rail will need to be resized a bit but the others should be printed at 100% and will be fine.
Most of these 3D parts were designed by me from scratch but a few used elements of other projects. Specifically, the trap door used the OpenForge 2.0 grate along with the reversible hinge by andyosier together, the Rancor door hinge is based on a design by Braunbaer, and the fire on the roasting table is simply the wall of fire by Talismancer resized.
Detail work and Assembly
There are a few very detailed things that need to be done to finish specific pieces described here.
The trap door:
To complete the trap door, test fit it into the hole you cut in the main floor and widen the hole if necessary so the trap door fits snugly but doesn't get caught on the edges of the hole. Fit the "Jabba's Palace Floor Cover" on top of this and make sure all clearances are good. Once you are satisfied, use superglue to attach the Floor Cover to the trap door (you will want to paint the trap door first).
Here is the trap door in action:
The roasting table:
In ROTJ there is a doner spit roast thingy behind Jabba's throne. To make this, take the 3d printed table and attach the two printed spit roast parts with the holes aligned with the long dimension of the table at least 15 mm apart (again, I would paint all of these pieces first). For the spit roast turning thing I used a nozzle cleaner wire that comes with an Ender 3 and stuck it through the holes in the roaster, bent it, and cut it to size using flush cutters. Once I was happy with this, I put some putty around the wire to simulate whatever alien meat was cooking and then painted it once it was dry. Finally, I glued the painted fire in the middle and did some touch up and details on the painted table with a fine point marker.
Jabba's throne:
Once you have printed and painted the main throne, the throne railing, the hookah and base piece and painted all of those, you are ready to assemble them. I did this using super glue without too much trouble. The only thing to be careful on is that you have the throne railing sized so that the flat portion where the hookah and frog creature bowl thing goes are about 15mm across. I glued the throne in place but if you want to make it slide forward like it does in the movie, you could print a rail or something. This is probably what I would have done if I'd remembered that the real trap door is not the fancy grated floor but in front of that.
Assembling the walls:
Check the overall model for wall placement. The way I did this was to glue the back wall cover to the back wall and glue the assembled part to the Jabba's throne stairs piece. none of these really need to be painted first if you plan on using a spray primer or something. Next, I glued two 90 degree angle pieces to the middle wall and glued that to the main floor surface using super glue. I then glued the two side walls to the floor using two 90 degree angle pieces on each and then glued them to the corner of the middle wall all with super glue.
Completing the main floor:
Before doing the next steps, it makes sense to prime and paint the entire floor and wall assembly. After you're happy with that, glue the mounted rancor head to the desired side wall, glue the Han solo in carbonite stand in place, glue the throne in place if desired, and finally glue the trap door hinges to the underside of the main floor in the appropriate spot making sure you have a fit that allows the door to freely fall. After this, use a 1/4 drill bit to drill a hole for the "Jabba's Palace floor switch." Fit the bigger piece on the top of the floor and then use a M3x20 screw through that and attach the bottom piece using a M3 nut so that the entire assembly can be rotated and the arm on the underside can "latch" the trap door shut. I found it helpful to paint a line on the main floor and the rotating piece on the top that marks the position when the door is shut.
Rancor pit and door:
For the Rancor pit you need one Rancor and I've linked to the model I used above. It also helps to have a lot of bones. I just found some 3d models of a bunch of random Pleistocene megafauna and printed them at appropriate scales. The complicated part is the door. To assemble this door print the parts labled "Rancor pit door," "Rancor pit brace and slots," and "Rancor door switch and hinge". Also, cut the remaining bit of plywood to 13cm x about 20cm. Fit the rancor pit braces with the three slots into the base brace (the piece shaped roughly like a dumbbell with holes in each end with the side with one slot exposed fit into the hole. I found it necessary to glue a second brace to the top of the door to keep the side braces from moving (I did this by simply printing and gluing a second bottom brace to the back of the upright arms). Take the piece that will be the bottom of the door and drill holes for M3 hardware to go through (I used M3x10 but shorter would work too). Place screw through the holes and attach nuts on the back side. When you are doing this, attach the two small pieces that printed with the pit brace and slots to the outer screws with the arms facing outward on each side (these are handles to help you lift). Fit the doors through the slots in the upright arms and test the motion. If all looks good, paint them and then reassemble. Finally, once you've got all of this working, glue the whole thing to the piece of plywood you cut earlier. Fit this assembly in the plywood box on either the right or left side. Lift the doors as high as you would like them to go and then test fit the "Rancor pit hinge and button" on the corner as shown in the pictures above. Mark the holes for this hing and attach it to the plywood box using M2 nuts and bolts. Once you're happy with the position of everything, glue the entire door assembly into the box using wood glue and you're done.
Here is a video of the door in action
Final thoughts
If I were doing this again, I probably wouldn't do it exactly the same way. I ended up modifying a few parts on the fly and tried to reflect that in the final models presented here but I didn't initially create this to be recreated by others (but some asked for this write-up). Have fun with it and make any modifications and let me know if you have any issues. This is perfectly sized to use with the Galactic Heroes Playskool figures but there are also plenty of models on Thingiverse that could be printed and used instead.
Similar models
3dwarehouse
free
Jabba's Throne Room Part 1
...jabba's throne room part 1
3dwarehouse
dais, trap door, dance floor and piano.
thingiverse
free
Brio railway buffer
...k is that you don't use enough glue - the toy needs to be strong enough that a toddler won't break it to pieces on day 1.
thingiverse
free
Placeable Trap Door by jender624
...read it through the trap door and place inside the top cover. glue bottom cover and top cover together. feel good about yourself.
thingiverse
free
Flexible Hinge by XENOTpro
...eems to work great.
the hinge can either be screwed or glued to a part. i used hot glue and didn't have any issues with that.
thingiverse
free
Mouse Coobe Live Trap by sfinktah
... "hinge" by ~1-2mm (i noticed my test mouse was trying to chew the hinges)
parts from v1 and v2 are cross compatible.
cg_trader
$15
Jabbas Throne Room - Set 10 - Main Hanger 1-18 scale | 3D
...oardgames legionterrain legioncampain starwarslegion jabba palace hanger slaveone naboofighter boba fett miniatures sci fi sci fi
cg_trader
$15
Jabbas Throne Room - Set 10 - Main Hanger 1-12 scale | 3D
...oardgames legionterrain legioncampain starwarslegion jabba palace hanger slaveone naboofighter boba fett miniatures sci fi sci fi
3dwarehouse
free
jabba's Rancor
...ba's rancor
3dwarehouse
rancor #dathomir #jabba #jabbas_rancor #pet #ran #ranc #rancor #sand #standart #swtfu #tatooine #tfu
3dwarehouse
free
Jabba's Palace 3.75
...jabba's palace 3.75
3dwarehouse
pt. 1 dance floor and trap door.
thingiverse
free
MPMD door hinge or corner piece
...g a bit inaccurate when i printed this design.
use support material and print the part on edge like it is oriented in the design.
Playskool
thingiverse
free
Gear for Playskool toy by bobkrot
...gear for playskool toy by bobkrot
thingiverse
thingiverse
free
Playskool Star Wars Endor Missile (2015?) by Tyhm
...ingiverse
wicket's missile from the playskool galactic heroes endor playset. (my kid lost it twice while i was modeling it)
thingiverse
free
Playskool Express Train Car Coupler by malamaker
...988, 1989, 1990, and 1992.
i do have more replacement parts that will be releasing, keep an eye on my posts in the coming months.
thingiverse
free
Gear for Playskool Busy Gears toy by mivanov
...i) makes circles that are a little bit wobbly, so i had to sand and acetone the inside a bit to get it to spin freely on the peg.
thingiverse
free
Playskool Express Train Car Coupler Mount by malamaker
...988, 1989, 1990, and 1992.
i do have more replacement parts that will be releasing, keep an eye on my posts in the coming months.
thingiverse
free
Playskool Express Train Car Wheel by malamaker
.../b00jr5c4fs) for the axle.
i do have more replacement parts that will be releasing, keep an eye on my posts in the coming months.
thingiverse
free
Playskool Form Fitter toy replacement shape blocks by caj
...t faster than creating from scratch
so you will have to sand or file the edges round
so the partials are on top of the originals
thingiverse
free
Steering Wheel for Playskool Take Apart Wooden Car by hsvtrail
...oken steering wheel of his playskiool take apart car. this is what i can up with. now it can be passed on to the next generation.
thingiverse
free
Playskool Kota My Triceratops Ride head mechanism by wikallen
...d it works perfectly.
i do not know what this part is called, or how to replace it. i just know it works from what he told me.
thingiverse
free
Power Rangers Playskool Heroes Projectile by smthbh
...metrical.
i had some issues with bed adhesion, so ended up printing on rafts, but that isn't necessary if yours adheres fine.
Rancor
3d_export
$99
star wars khetanna jabba sail barge
...after the jedi knight luke skywalker killed jabba's pet rancor the crime lord demanded skywalker and his companions han...
3d_export
$40
star wars sci-fi felucia stuff
...big bladder (saleucami)<br>1 mushroom(glowing gomba)<br>1 segmented (huge bubble tree)<br>1 rancor ( that is not rigged )<br>1 background rendered hdr...
thingiverse
free
Rancor statue
...rancor statue
thingiverse
rancor. hope you'll enjoy. best!
thingiverse
free
Rancor by lostinlmbo
...rancor by lostinlmbo
thingiverse
head of a rancor from jabba's palace
thingiverse
free
Rancor by Incorrect
...rancor by incorrect
thingiverse
model of star wars, rancor created in z brush
thingiverse
free
Rancor Buddha by JohnMaxipad
...rancor buddha by johnmaxipad
thingiverse
meh
3dcadbrowser
free
Rancor
...software.this 3d object can be downloaded in .max, .obj, .3ds, .fbx, .dxf, .lwo, .stl, .wrl, .ma, .dae, .x and .asc file formats.
thingiverse
free
Rancor clan coin 2016 by Aos4life
...rancor clan coin 2016 by aos4life
thingiverse
this is a coin i designed with the rancor clan of mmcc logo.
sketchfab
$25
Rancor Gargoyle Head
... you need 3d game assets or stl files i can do commission works. - rancor gargoyle head - buy royalty free 3d model by paburoviii
thingiverse
free
Rancor dungeon door by JuanMa76
...oor by juanma76
thingiverse
custom rancor dungeon door. not acurrate but it works fine.
4mm noozle
sunlu pla
hot end:195
bed: 60
Jabba
turbosquid
$39
Jabba the Hutt
...d model jabba the hutt for download as max, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1616227)
3d_export
$99
star wars khetanna jabba sail barge
...mats: - (12.jpg) 8192 x 8192<br>v-ray render and materials (1.50 sp4a)<br>lighting setup is not included in the file!
turbosquid
$29
3D Printable Soccer Jabba Ball Ornament model
... soccer jabba ball ornament model for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1454567)
cg_studio
$149
Star Wars Han Solo in Carbonite3d model
...solo carbonite starwars character scifi sci-fi man sculpture movie jabba souvenir .obj .max .lwo .fbx .c4d .3ds - star...
thingiverse
free
Jabba Hutt by mifth
...jabba hutt by mifth
thingiverse
jabba hutt.
make your jabba!
thingiverse
free
Jabba the Hut by MrYoung64
...jabba the hut by mryoung64
thingiverse
jabba the hut
thingiverse
free
Jabba Keychain by Caardo
...jabba keychain by caardo
thingiverse
jabba keychain. two options available for the ring itself.
thingiverse
free
Jabba The Hutt by Jace1969
...bba the hutt by jace1969
thingiverse
hi ajaxslasher yes i do have jabba the hutt. hopefully this is what your after. cheers jace
thingiverse
free
Jabba Candle Holder by gouldm2001
...esh mixer to put some holes in jabba for candles ala this christmas card i got:
https://www.polaroidcube.com/image/jabba-menorah/
free3d
free
Star Wars Jabba
...star wars jabba
free3d
no surface
Playset
turbosquid
$15
PlaySet
...turbosquid
royalty free 3d model playset for download as max on turbosquid: 3d models for games, architecture, videos. (1439097)
turbosquid
$15
indor-playset
...quid
royalty free 3d model indor-playset for download as max on turbosquid: 3d models for games, architecture, videos. (1335786)
turbosquid
$25
Park playset
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Indoor Playset 167
...3d model indoor playset 167 for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1385241)
turbosquid
$10
Indoor Playset 112
...3d model indoor playset 112 for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1384863)
3d_export
$25
Playground 3D Model
...playground 3d model 3dexport playground building playset outdoor exterior slide ladder children kids playground 3d model...
3d_export
$10
Playground horse 3D Model
...equipment slide tube playhouse jungle gym swing tower ladder playset playground horse...
3d_export
$70
Playground Set 3D Model
...equipment slide tube playhouse jungle gym swing tower ladder playset playground set 3d model etmodels 65179...
cg_studio
$70
Playground Set3d model
...equipment slide tube playhouse jungle gym swing tower ladder playset .3ds .fbx .max .obj - playground set 3d model,...
3dbaza
$7
Indoor Playset (102061)
...indoor playset (102061)
3dbaza
indoor playset 3d
Galactic
3d_export
$5
Galactic clam
...galactic clam
3dexport
galactic clam
turbosquid
$59
Galactic Observatory
...oyalty free 3d model galactic observatory for download as c4d on turbosquid: 3d models for games, architecture, videos. (1521342)
turbosquid
$15
Galactic Senate
... model galactic senate for download as max, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1642222)
turbosquid
$50
Virgin Galactic
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$7
Galactic Explosion Rifle
...galactic explosion rifle
3dexport
turbosquid
$99
Galactic Robot_03 - Low_poly
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$99
Galactic Robot_02 - Low_poly
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$99
Galactic Robot_01 - Low_poly
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$99
Galactic Robot_07 - Low_poly
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$99
Galactic Robot_06 - Low_poly
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Pit
3d_export
$5
pit
...pit
3dexport
pit
3d_export
$5
pit
...pit
3dexport
3d model pit
3d_export
$5
pit
...pit
3dexport
pit obj,fbx,blend
3d_export
$5
Pit
...pit
3dexport
high-resolution well, can be used as photos, games, clips
turbosquid
$29
Pavement pit
...squid
royalty free 3d model pavement pit for download as max on turbosquid: 3d models for games, architecture, videos. (1192495)
turbosquid
$15
Fire pit
...d
royalty free 3d model fire pit for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1577348)
turbosquid
$4
Fire Pit
...id
royalty free 3d model fire pit for download as ma and obj on turbosquid: 3d models for games, architecture, videos. (1500433)
turbosquid
$65
Pit Droid
...lty free 3d model pit droid for download as skp, 3dm, and obj on turbosquid: 3d models for games, architecture, videos. (1536387)
turbosquid
$79
medieval pit
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
Charcoal Pit
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Palace
3d_export
$15
palace
...palace
3dexport
a palace of greek methalology<br>3dsmax 2017<br>vrayrt 3.6
3d_export
$100
kremlin palace
...kremlin palace
3dexport
kremlin palace
turbosquid
$60
PALACE
...
turbosquid
royalty free 3d model palace for download as max on turbosquid: 3d models for games, architecture, videos. (1320004)
3d_export
free
palace
...palace
3dexport
3d_export
$18
royal palace-shabak-vertical palace lantern
...royal palace-shabak-vertical palace lantern
3dexport
royal palace-shabak-vertical palace lantern<br>3ds max 2015
turbosquid
$359
Palace
...e 3d model palace for download as max, max, max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1564878)
turbosquid
$50
Palace
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Palace
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
palace
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$65
palace
...palace
3dexport
simple rendering of the scene file
Heroes
3d_ocean
$30
Super Hero
...hero mask ninja super hero sword zbrush
super hero created in zbrush 4.0 hero body—6 division levels 1.668 poly to 1.705mil poly.
turbosquid
$70
hero
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$59
Hero
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$22
Hero
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
HERO
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Heros Frames Super heroes Frames
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
htc Hero
...ефон , смартфон , htc
смартфон htc hero, черный
3ddd
free
MARVEL-Heroes-1
...marvel-heroes-1
3ddd
marvel
marvel-heroes-1
turbosquid
$280
Hero Knight
...bosquid
royalty free 3d model hero knight for download as ma on turbosquid: 3d models for games, architecture, videos. (1326296)
turbosquid
$55
Super Hero
...squid
royalty free 3d model super hero for download as blend on turbosquid: 3d models for games, architecture, videos. (1387035)
Scaled
turbosquid
$20
Weight scale or Bathroom Scale
...ght scale or bathroom scale for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1664576)
turbosquid
$19
Scale
...e
turbosquid
royalty free 3d model scale for download as fbx on turbosquid: 3d models for games, architecture, videos. (1411722)
turbosquid
$5
Scales
...s
turbosquid
royalty free 3d model scales for download as ma on turbosquid: 3d models for games, architecture, videos. (1393439)
turbosquid
$40
Scale
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$17
Scales
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
Scale
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Scale
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$7
of scales
...s have a flat point of support. the samples are rendered in the standard cinema 4d renderer. enjoy your use and creative success.
3d_export
$5
scale knob
...scale knob
3dexport
scale knob
3d_export
$20
cartoon weight scale or bathroom scale
...cartoon weight scale or bathroom scale
3dexport
texture size:512px number of texture:1 texture format: png