Thingiverse
![Ikea Antilop adjustable footrest by Pearlic](/previews/8113151.jpg)
Ikea Antilop adjustable footrest by Pearlic
by Thingiverse
Last crawled date: 3 years, 5 months ago
This is my attempt to create easy adjustable footrest for IKEA Antilop high chair.
Print settings:
See the section. The files print easy also on the small printers (10x10, no heatbed).
Parts needed:
3d printed parts set
4 screws (5mm diameter) with the nuts and washers
2 pipes 28cm long (pvc hot water pipes 17mm outer and 12 inner diameter)
2 pipes 52cm long (pvc hot water pipes 17mm outer and 12 inner diameter)
Felt or rubber pieces to secure the arms on hair legs (at least 2mm thickness for each arm and clamp) (note it is required for the arms not to move on the legs)
Note: different pipes with 17mm outer diameter can be used (and at least 12mm inner diameter)
Build instruction:
Print all the parts (number of parts to be printed in file name)
Cut the pipes for the desired length
Insert 4 pipes into 2 holder parts
Secure short pipes with the 2 endings (1 for each side) - you may use hot glue and any kind of separator to hold endings in place inside the pipes
Set the width of the footrest adjusting the pipes and holders - the holders should be as nearest the hair legs as possible
insert the longer pipes endings into the arms (P and L respectively)
Secure the pipes with the 2 endings
Insert screws to the holes (you may want to insert the screw from the arm side)
Glue felt or rubber pieces inside the arm and clamp to hold the footrest on place
Secure the arms with the clamps, washer and nuts on the hair legs
NOTE: use the picture as a referene on how the parts should be adjisted and folded together.
NOTE2: Arms angles are slightly different than a straight line so the pipe stress should block them so that they do not move.
To adjust the footrest high, simply loosen the screws, move the footrest down a bit and secure back. To longer pipes should freely adjust the whole footrest to the space between the legs (tested! ;))
Print settings:
See the section. The files print easy also on the small printers (10x10, no heatbed).
Parts needed:
3d printed parts set
4 screws (5mm diameter) with the nuts and washers
2 pipes 28cm long (pvc hot water pipes 17mm outer and 12 inner diameter)
2 pipes 52cm long (pvc hot water pipes 17mm outer and 12 inner diameter)
Felt or rubber pieces to secure the arms on hair legs (at least 2mm thickness for each arm and clamp) (note it is required for the arms not to move on the legs)
Note: different pipes with 17mm outer diameter can be used (and at least 12mm inner diameter)
Build instruction:
Print all the parts (number of parts to be printed in file name)
Cut the pipes for the desired length
Insert 4 pipes into 2 holder parts
Secure short pipes with the 2 endings (1 for each side) - you may use hot glue and any kind of separator to hold endings in place inside the pipes
Set the width of the footrest adjusting the pipes and holders - the holders should be as nearest the hair legs as possible
insert the longer pipes endings into the arms (P and L respectively)
Secure the pipes with the 2 endings
Insert screws to the holes (you may want to insert the screw from the arm side)
Glue felt or rubber pieces inside the arm and clamp to hold the footrest on place
Secure the arms with the clamps, washer and nuts on the hair legs
NOTE: use the picture as a referene on how the parts should be adjisted and folded together.
NOTE2: Arms angles are slightly different than a straight line so the pipe stress should block them so that they do not move.
To adjust the footrest high, simply loosen the screws, move the footrest down a bit and secure back. To longer pipes should freely adjust the whole footrest to the space between the legs (tested! ;))
Similar models
thingiverse
free
![Pipe Clip/Grip/Clamp for IKEA Antilop chair by DLCJosh](/t/8356382.jpg)
Pipe Clip/Grip/Clamp for IKEA Antilop chair by DLCJosh
...andium etc.)
this clamp goes onto the front 2 legs as support for a wooden footrest to sit on top.
fits m6 bolt through the hole.
thingiverse
free
![Wall mounted filament spool holder by algoritm](/t/8662567.jpg)
Wall mounted filament spool holder by algoritm
...bs.
radius of the spool pipe is 10mm (20mm diameter). the end plugs are for pipes with an inner diameter of 8.5mm. print 2 plugs.
thingiverse
free
![E3D adjustable hot-end holder by xammax](/t/9028607.jpg)
E3D adjustable hot-end holder by xammax
... then use m4 screws to mount the hot end and the extruder.
printed with pla (no issue, there is not much heat left on that end.
thingiverse
free
![MTB bar end with screw to clamp by Jori](/t/8188160.jpg)
MTB bar end with screw to clamp by Jori
...s m5x20 din 912.
can be put easily in the handle bar and also removal is easy; internal clamping by tightening the central screw.
thingiverse
free
![Anet A8 - Hot end wire clamp by Keepars](/t/8567815.jpg)
Anet A8 - Hot end wire clamp by Keepars
...screws on directly to the stock bearing using the original screws just remove the 2 screws on the bearing and screw the clamp on.
thingiverse
free
![Glasshouse rain gutter end by skynat](/t/8643864.jpg)
Glasshouse rain gutter end by skynat
...downwards.
width: 40mm outer and 35mm inner
height pipe: 27mm
height overall: 51mm
diameter pipe inner: 24mm
diameter outer: 30mm
thingiverse
free
![cover collar pipe by Arcade_Machine](/t/8264311.jpg)
cover collar pipe by Arcade_Machine
...e inner diameter is18mm.
2º
the outer diameter is 58mm.
the inner diameter is13mm.
if you want a specific measure, comment on it.
thingiverse
free
![Ultimate Ball Bearing Spool Holder 3000 by NanoBotAstronaut](/t/8714342.jpg)
Ultimate Ball Bearing Spool Holder 3000 by NanoBotAstronaut
...aurarum wombot exilis xl but should work well on similar 30mm extruded frames. the insert assembly comes in 2...
thingiverse
free
![Ergonomic Wheel insert by Kineticdesignz](/t/8087214.jpg)
Ergonomic Wheel insert by Kineticdesignz
...
insert for an torn ergonomic chair wheel shaft. adjust according to your wheel diameter.
16mm outer diameter
6mm inner diameter
thingiverse
free
![hair dryer / hair straightener holder holster by Order_3D](/t/8752257.jpg)
hair dryer / hair straightener holder holster by Order_3D
...ghtener holder holster.
you can adjust part diameter by heating the part -> bend -> cool down.
you will need 2 x m3 screws.
Pearlic
thingiverse
free
![Fire extinguisher 1:25 scale by Pearlic](/t/8148192.jpg)
Fire extinguisher 1:25 scale by Pearlic
...el in 1:25 scale. you can print just the base, the model without the handle (to be added from paper or plastic) or just the base.
thingiverse
free
![CO2 bottle 1:25 scale by Pearlic](/t/8148195.jpg)
CO2 bottle 1:25 scale by Pearlic
...el in 1:25 scale. you can print just the base, the model without the handle (to be added from paper or plastic) or just the base.
thingiverse
free
![Mark IV Male simple rifle 1:25 by Pearlic](/t/8642902.jpg)
Mark IV Male simple rifle 1:25 by Pearlic
...ifle 1:25 by pearlic
thingiverse
simple rifles for mark iv 1/25 scale papercraft model.
print x3 (one front and two for turrets)
thingiverse
free
![Mark IV Male Covers 1:25 by Pearlic](/t/8642901.jpg)
Mark IV Male Covers 1:25 by Pearlic
...iv papercraft model in 1:25 scale
one small with hinge - print x4
one smal without hinge - print x2
huge one with nuts - print x2
thingiverse
free
![Mark IV Male Treadmill 1:25 by Pearlic](/t/8642900.jpg)
Mark IV Male Treadmill 1:25 by Pearlic
... the length to your paper parts by cutting the bolt or just glue into the plastic part without changes
treadmill niche - print x4
thingiverse
free
![Leopold K5E Railway Cannon Axle Box 1:25 by Pearlic](/t/8642868.jpg)
Leopold K5E Railway Cannon Axle Box 1:25 by Pearlic
....thingiverse.com/thing:2596164)
choose one version that suits your needs and print x24 (x12 per each platform - x6 for each side)
thingiverse
free
![Leopold K5E Railway Cannon Wheels and axis 1:25 by Pearlic](/t/8642887.jpg)
Leopold K5E Railway Cannon Wheels and axis 1:25 by Pearlic
...heels of your choice and 12 fully assembled axis parts (3 parts each). -> 12 wheels / 6 axis per platform (6 wheels per side)
thingiverse
free
![Schienenwolf (Railroad plough) 1/87 (HO) by Pearlic](/t/8599701.jpg)
Schienenwolf (Railroad plough) 1/87 (HO) by Pearlic
...hare your print if done, do not hesitate to share also some pictures of painted model, i will add them to my facebook page too ;)
Antilop
thingiverse
free
![Ikea Antilop changing table accessories by niko83dk](/t/8816137.jpg)
Ikea Antilop changing table accessories by niko83dk
...e accessories by niko83dk
thingiverse
bought a second hand antilop ikea table.
4 fixing inserts
2 plastic stop cap
were missing.
thingiverse
free
![Ikea antilop child chair clip by buged86](/t/8062367.jpg)
Ikea antilop child chair clip by buged86
...ikea antilop child chair clip by buged86
thingiverse
just my design of a clip for the ikea child chair.
thingiverse
free
![Ikea Antilop felt pad cap by HAMMER_T](/t/8147282.jpg)
Ikea Antilop felt pad cap by HAMMER_T
...tilop felt pad cap by hammer_t
thingiverse
the diameter of the felt pads must be around 40mm.
the fusion360 files are also here.
thingiverse
free
![Pipe Clip/Grip/Clamp for IKEA Antilop chair by DLCJosh](/t/8356382.jpg)
Pipe Clip/Grip/Clamp for IKEA Antilop chair by DLCJosh
...andium etc.)
this clamp goes onto the front 2 legs as support for a wooden footrest to sit on top.
fits m6 bolt through the hole.
thingiverse
free
![Antilop IKEA leg holder by Luffare](/t/8644776.jpg)
Antilop IKEA leg holder by Luffare
...nt two and hang the legs as the picture or print one and hang the legs vertically.
if you make one please post a pic or a comment
thingiverse
free
![Highchair leg storage clip for IKEA Antilop by KRG](/t/8014624.jpg)
Highchair leg storage clip for IKEA Antilop by KRG
...lip for ikea antilop by krg
thingiverse
other half complained that the corners are sharp so made them round. no more complaints.
thingiverse
free
![Leila Rosano. Antilope . Proyectual 2017 by CatedraCaceresUNA](/t/8660597.jpg)
Leila Rosano. Antilope . Proyectual 2017 by CatedraCaceresUNA
...017.
el poder y lo femenino a través de la figura de la bruja
mas info,https://catedracaceresuna.wordpress.com/leila-rosano-2017/
thingiverse
free
![IKEA Antilop highchair leg clip by Herorich](/t/8908782.jpg)
IKEA Antilop highchair leg clip by Herorich
...here. i noticed how difficult it was to keep the chair legs together.
i began to think about a solution and this is the result.
thingiverse
free
![IKEA Antilop baby chair leg hook](/t/4980870.jpg)
IKEA Antilop baby chair leg hook
... since as always, i included the freecad model.
i added the v2 version with rounded bottom of the hook to reduce the sharp edges.
Footrest
thingiverse
free
![Motorcycle passenger footrest](/t/4773740.jpg)
Motorcycle passenger footrest
...motorcycle passenger footrest
thingiverse
diy motorcycle footrest for 19mm aluminium tube
thingiverse
free
![Footrest Mount by Stonequest4551](/t/8064872.jpg)
Footrest Mount by Stonequest4551
...by stonequest4551
thingiverse
this is the mount that goes on the underside of many common gaming chairs to hold on the footrest.
thingiverse
free
![footrest hoverboard Children by IntreD](/t/8494040.jpg)
footrest hoverboard Children by IntreD
...footrest hoverboard children by intred
thingiverse
footrest hoverboard children
thingiverse
free
![Songmics Footrest Cap by T0_0rk](/t/9683237.jpg)
Songmics Footrest Cap by T0_0rk
...songmics footrest cap by t0_0rk
thingiverse
caps for songmics chair with footrest.
thingiverse
free
![Pajero Footrest by TalorKeren](/t/8231242.jpg)
Pajero Footrest by TalorKeren
...alorkeren
thingiverse
footrest pajero 2012
prinetd with abs
nozzle temp - 240c
bed temp - 110c
ambient temp - 42-45c
by talor.k
thingiverse
free
![Reposapé Bicicleta / Bicycle Footrest by ToribioCosmico](/t/8794569.jpg)
Reposapé Bicicleta / Bicycle Footrest by ToribioCosmico
...reposapé bicicleta / bicycle footrest by toribiocosmico
thingiverse
reposapié para bicicleta.
bicycle footrest.
thingiverse
free
![Footrest Cap (Super SOCO)](/t/4890169.jpg)
Footrest Cap (Super SOCO)
...petg and fitted perfectly with a few mallet taps.
for increased security, you might drill a hole in the footrest and add a screw.
thingiverse
free
![Stressless Footrest Clamp Repair by phin13th](/t/8566599.jpg)
Stressless Footrest Clamp Repair by phin13th
...epair by phin13th
thingiverse
clamp for a broken clamp that is originally used in a stressless loungechair footrest combination.
thingiverse
free
![baby jogger city mini footrest by 2354082](/t/8612219.jpg)
baby jogger city mini footrest by 2354082
...baby jogger city mini footrest by 2354082
thingiverse
baby jogger city mini footrest
thingiverse
free
![Ikea BLÅMES Highchair Footrest by insobar](/t/8164715.jpg)
Ikea BLÅMES Highchair Footrest by insobar
...print 2, one for each end of a 19mm bit of decking timber. it can be inserted into the slots at whichever height suits your baby.
Ikea
thingiverse
free
![ikea hook for ikea SAMLA boxes by dericcio](/t/5035629.jpg)
ikea hook for ikea SAMLA boxes by dericcio
...ikea hook for ikea samla boxes by dericcio
thingiverse
ikea samla box hook
thingiverse
free
![Ikea cable holder](/t/4925521.jpg)
Ikea cable holder
...ikea cable holder
thingiverse
ikea
thingiverse
free
![Ikea power strip for Ikea Lack](/t/4937028.jpg)
Ikea power strip for Ikea Lack
...d.
the .stl file combines two of parts so use slicer either separate them ( s3d option "separate connected surfaces" )
thingiverse
free
![IKEA logo by LogoGuy](/t/8498459.jpg)
IKEA logo by LogoGuy
...ikea logo by logoguy
thingiverse
the ikea logo
thingiverse
free
![Clou IKEA by lucke34](/t/8853653.jpg)
Clou IKEA by lucke34
...clou ikea by lucke34
thingiverse
clou ikea
thingiverse
free
![IKEA Stall Bracket](/t/4688829.jpg)
IKEA Stall Bracket
...ikea stall bracket
thingiverse
ikea stall bracket
thingiverse
free
![IKEA FAKTUM Karusell](/t/4669447.jpg)
IKEA FAKTUM Karusell
...ikea faktum karusell
thingiverse
ikea faktum karusell
thingiverse
free
![IKEA Bumerang clip](/t/4987248.jpg)
IKEA Bumerang clip
...ikea bumerang clip
thingiverse
ikea bumerang clip
thingiverse
free
![Ikea curtain by h2bazza](/t/8750061.jpg)
Ikea curtain by h2bazza
...ikea curtain by h2bazza
thingiverse
support for ikea curtain
thingiverse
free
![IKEA roller by Ontop](/t/8651921.jpg)
IKEA roller by Ontop
...ikea roller by ontop
thingiverse
ikea roller bracket
Adjustable
thingiverse
free
![Adjustable Wrench](/t/4922575.jpg)
Adjustable Wrench
...adjustable wrench
thingiverse
working adjustable hand wrench.
thingiverse
free
![PPG adjustable propellers adjusting device by x3x3x](/t/8885050.jpg)
PPG adjustable propellers adjusting device by x3x3x
...ppg) adjustable propellers adjusting device. 95 mm blade width. android phone, apple, symbian os. applications for free download.
thingiverse
free
![Adjustable foot](/t/4709284.jpg)
Adjustable foot
...adjustable foot
thingiverse
just another adjustable foot for m5 screw (better if is self-locking nut).
diameter 20mm
thingiverse
free
![Adjustment Handle by adamdthornton](/t/8204925.jpg)
Adjustment Handle by adamdthornton
...adjustment handle by adamdthornton
thingiverse
adjustment handle
thingiverse
free
![Adjustable foot by denis4](/t/8792398.jpg)
Adjustable foot by denis4
...adjustable foot by denis4
thingiverse
adjustable leg
thingiverse
free
![Adjustable Extruded by CruiseLee](/t/8863171.jpg)
Adjustable Extruded by CruiseLee
...adjustable extruded by cruiselee
thingiverse
adjustable extruded
thingiverse
free
![adjustable spanner by stevehaines](/t/8981434.jpg)
adjustable spanner by stevehaines
...adjustable spanner by stevehaines
thingiverse
adjustable spanner
thingiverse
free
![Adjustable Wrench by AdamsLab](/t/8267934.jpg)
Adjustable Wrench by AdamsLab
...h by adamslab
thingiverse
this is an adjustable wrench.
the top jaws slide into the main body, and you use the nut to adjust it.
thingiverse
free
![Lawnmower adjustment handle](/t/4926472.jpg)
Lawnmower adjustment handle
...lawnmower adjustment handle
thingiverse
lawnmower adjustment handle
thingiverse
free
![Adjustable Frame by Quinventor](/t/8776329.jpg)
Adjustable Frame by Quinventor
...adjustable frame by quinventor
thingiverse
an adjustable picture frame