igloo hinge by yatesgd

...igloo replacement cooler hinge by cswaim thingiverse igloo replacement cooler hinges!

...toy igloo with hinged door by jinolimi thingiverse toy igloo with door

...rst thing, a replacement hinge for the igloo 120 quart polar cooler. a nice cooler, but the hinges came apart somewhat quickly.

...completely solid all the way through. the holes are spaced 44mm apart width wise, check your cooler's hinges before printing.

...ch by beaker thingiverse a replacement latch for a igloo maxcold cooler. update (10/14): reinforced hinge to prevent breaking.

...a and worked perfect. something like semiflex or esun flexible would work as well. a soft nylon like bridge might work nice also

...so fit other coolers, and some only require 2 hinges, where as the 100qt requires 3. print only in a flexible material, like tpu!

...n overview here:https://youtu.be/vm4fu0qnlts also, i made the tinkercad file public: https://www.tinkercad.com/things/knk0pkv5snt

...the original hinge pin (or just design/print an approximately .170" diameter by 1.285" length pin printed horizontally)

...igloo by skylercz thingiverse igloo

...ingiverse rear wiper pivot cover. made this for a friend to replace the cap that broke. painted in flat black for a great match!

...pters? this is the perfect scoop! acts as a measuring scoop and a tapered funnel to get the coffee neatly into the filter. enjoy!

...ch of sanding for best fit, and a drop of superglue to hold it together. and...everything is printed upside down for best finish.

...nd. the front edge that takes the majority of the force was too thin and broke off. i beefed it up to 4mm for some added support.

...strength. i ran the second draft on a markforged mark ii with onyx and carbon fiber inlay. tool should last as long as the truck!

...original mb part was way too short to even work. i also beefed up the latch at the end of the handle to improve the cup strength.

...t;raw" is the original stl direct from the scanner. the printed model took approx 4.5 hours and is approx 4" x 3".

... rep g profiles i even managed to print it at 50 micron. honestly not a massive improvement considering it took an hour to print.

...igloo thingiverse this is a model of an igloo with an extra large entrance.

...igloo by skylercz thingiverse igloo

...igloo by coupdeforce thingiverse a simple igloo.

...an igloo by jlbell thingiverse this is a igloo, it can be for legos and other small things!=)

...igloo by roman_hegglin thingiverse same as the igloo in thing 23853, but not hollow.http://www.thingiverse.com/thing:23853

...igloo by doogle3 thingiverse model of a basic igloo, these were used by inuit of northern canada and made of blocks of snow.

...igloo by jesus_ronaldo thingiverse this was designed in tinkercad.

...igloo blocky and normal by 3d_printing_pal thingiverse this is an igloo.

... smooth out the interior surface and make some modifications so that support material is not needed. makes a great hamster house!

...hinge thingiverse hinge for rc vehicles

...hinge thingiverse just a basic hinge

...hinge thingiverse simple hing for printing at once or piece for piece...

...erse hinge in the style of a ladder hinge. 5mm bolt and nut required to allow it to function 5mm screw holes 180 degree rotation

...hinge by sbenetti1 thingiverse hinge

...hinge by jfpoutasse thingiverse hinge

...hinge by kyofr thingiverse hinge

...hinge by jonspencer thingiverse hinge

...hinges by mahee3d thingiverse hinges

...hinge by hobbz thingiverse hinge