Thingiverse
Iambic Paddles (Narrow Version) by ReallyBigTeeth
by Thingiverse
Last crawled date: 3 years, 1 month ago
If you like what you see here, consider leaving a tip.
Remixed from an excellent design by Thingiverse user and certified amateur radio operator Loren Butler (V01PWF), the intent of this project was to make a set of 3D printable iambic paddles that were as portable as possible, yet comfortable enough to use at a desk. This is the narrow version of these paddles and are not base mountable. The base mountable version is 10 mm wider and can be found here, and a mini version can be found here.
Hardware Used:
3x 6-32 x 1 inch phillips flat pan head screws for paddle pivots and ground contact
2x 6-32 phillips flat pan head screws trimmed to 11.5mm thread length for paddle contacts
2x 6-32 nuts/springs and washers for paddle contact screws
4x 6-32 1/4 inch phillips flat pan head screws for attaching the cover
1x 1/8 inch stereo jack or hot glue
1x Spring from a retractable pen (3.5mm outer diametre, 10mm length)
or 2x neodymium magnets
or 1x 3D printable spring designed by Mlogith
3x short lengths of stranded wire
The paddles use a spring from an empty retractable ball point pen, and are tension adjustable via a set of pockets along the inside of each arm. A suggestion from wz2prich is to use neodymium magnes glued to the arms instead of a spring. Arm travel to contact is adjustable but the resting point is fixed. Using springs in place of the nuts on the paddle contact screws can make adjustments faster and easier. The plug at the rear of the paddles is a 1/8" stereo jack which could lead to an electronic keyer, radio, or pc interface. A tip from Thingiverse user KD9AYE is to glue the wires in place, eliminating the need for a stereo jack. Photos of his build of the narrow and base mountable versions of these paddles can be found here. Using springs in place of the nuts on the paddle contact screws can make adjustments faster and easier.
Remixed from an excellent design by Thingiverse user and certified amateur radio operator Loren Butler (V01PWF), the intent of this project was to make a set of 3D printable iambic paddles that were as portable as possible, yet comfortable enough to use at a desk. This is the narrow version of these paddles and are not base mountable. The base mountable version is 10 mm wider and can be found here, and a mini version can be found here.
Hardware Used:
3x 6-32 x 1 inch phillips flat pan head screws for paddle pivots and ground contact
2x 6-32 phillips flat pan head screws trimmed to 11.5mm thread length for paddle contacts
2x 6-32 nuts/springs and washers for paddle contact screws
4x 6-32 1/4 inch phillips flat pan head screws for attaching the cover
1x 1/8 inch stereo jack or hot glue
1x Spring from a retractable pen (3.5mm outer diametre, 10mm length)
or 2x neodymium magnets
or 1x 3D printable spring designed by Mlogith
3x short lengths of stranded wire
The paddles use a spring from an empty retractable ball point pen, and are tension adjustable via a set of pockets along the inside of each arm. A suggestion from wz2prich is to use neodymium magnes glued to the arms instead of a spring. Arm travel to contact is adjustable but the resting point is fixed. Using springs in place of the nuts on the paddle contact screws can make adjustments faster and easier. The plug at the rear of the paddles is a 1/8" stereo jack which could lead to an electronic keyer, radio, or pc interface. A tip from Thingiverse user KD9AYE is to glue the wires in place, eliminating the need for a stereo jack. Photos of his build of the narrow and base mountable versions of these paddles can be found here. Using springs in place of the nuts on the paddle contact screws can make adjustments faster and easier.
Similar models
thingiverse
free
Iambic Paddles (Base Mountable Version) by ReallyBigTeeth
...ng the need for a stereo jack. photos of his build of the narrow and base mountable versions of these paddles can be found here.
thingiverse
free
Iambic Paddles (Mini Version) by ReallyBigTeeth
...d contact screw. two optional screws at the rear of the case can also be used to hold the cover in place, but are not necessary.
thingiverse
free
Hobie Kayak H-Rail Paddle Mount by JESTERxHEAD
...ut, stainless
for mounting the paddle clip:
2x #10-24 x .50" lg stainless pan head screw
2x #10-24 nylon lock nut, stainless
thingiverse
free
Iambic Paddles (For resin printing) by ratmandu
...ratmandu thingiverse iambic paddles for cw (morse code). very similar to others out there, but designed to be printed...
thingiverse
free
uBitX Single Lever Morse Code Paddle by AngelDMercedes
...ion cable (with two 3.5mm jacks) or any other cable with one 3.5mm audio jack.
build and test video:https://youtu.be/opoirwk1lkg
thingiverse
free
Artillery Genius - SWX1 filament sensor holder
...5mm
2x flat head screw m3 x 8mm
3x nut m3
2x t-nut m3
1x ptfe tubing
2x pc4 m6
pc4 m6https://www.amazon.de/gp/product/b07n6h43fw
thingiverse
free
Sim Racing Paddle Shifter (simple print) by PhronemoS
...s:
2x - neodymium magnet (size 8x2mm)
3x - screw m3x25mm
1x - screw m3x30mm
4x - nut m3
update 09.03.2021
added solid base model.
thingiverse
free
EXT3 Bowden 1.75 by Eldrid
...tubing 4mm od 2mm id (16mm, 12mm long)
2x ptfe fitting pc4-m6 (m6 screw, for 4mm ptfe tube)
1x mk7 drive gear for 1.75mm filament
thingiverse
free
Leg Strap Base for Iambic Paddles by miracolifarm
...eg strap base for reallybigteeth's iambic paddles (base mountable). https://www.thingiverse.com/thing:2054230
nice snug fit.
thingiverse
free
Filament Spool Arm by jesc
...ap.
requires:
2x m3 screws and nuts (optional: another 2x)
2x m8 nuts
1x m8 threaded rod (~10cm long)
1x m8 washer
1x 608 bearing
Iambic
thingiverse
free
Iambic Keyer by matrhint
...iambic keyer by matrhint
thingiverse
it is a iambic morse code keyer
thingiverse
free
mini iambic paddle by OK1IAK by bubnikv
...mini iambic paddle by ok1iak by bubnikv
thingiverse
mini iambic paddle by ok1iak
thingiverse
free
Oversize Paddles for Vibroplex Iambic by N7JX
...lex iambic a bit too "dainty". these are quite a bit larger, similar to the conversion paddles vibroplex sells for $15.
thingiverse
free
Micro Iambic CW Key by the-kenny
...r mobile use. it uses a hacksaw blade and three m3 screws.
version 2 with better wire routing, strain relief, and mounting holes.
thingiverse
free
Leg Strap Base for Iambic Paddles by miracolifarm
...eg strap base for reallybigteeth's iambic paddles (base mountable). https://www.thingiverse.com/thing:2054230
nice snug fit.
thingiverse
free
Yet another iambic CW paddle by dtemes
...rial:
4 x m5x20mm
3 x m5x30mm
7 x m5 nuts
2 x m4x10mm
4 magnets 5x5x1mm for the paddle return
the base was printed with supports.
thingiverse
free
Large CW Morse Code Iambic Key by jzkmath
... just got into morse code not too long ago.
use the iambic2 file for printing, as it has been rotated to be flat on your printer.
thingiverse
free
Non-iambic Morse code key with paddles V2 by cebess
...mber of years ago but decided to streamline it and make the paddles more secure so this is a v2 of my previous non-iambic paddle.
thingiverse
free
Replacement Paddles for CW Morse Iambic by kkessler
...em to work well. be careful when resoldering the brass contacts, because if you take too long, you will melt and bend the paddle.
thingiverse
free
Iambic Paddles (For resin printing) by ratmandu
... washers, and nuts.
spring is 0.21in od.
pockets on bottom to glue in magnets (i'm using 10mm diameter, 3mm thick neodymium).
Reallybigteeth
thingiverse
free
ALPS Macro Keycaps by ReallyBigTeeth
...y reallybigteeth
thingiverse
if you like what you see here, consider leaving a tip.
custome made alps keycaps for macro keyboard
thingiverse
free
Earring/Jewellery Stand by ReallyBigTeeth
...he print bed. clip together to assemble. use a dab of glue if you wish.
thanks goes out to kyllikki for physical connections.
thingiverse
free
Corsair Voyager GT USB Case for Keyring by ReallyBigTeeth
...e what you see here, consider leaving a tip.
case for a corsair voyager gt usb stick that has a hole for attaching to a key ring.
thingiverse
free
Ergodox ALPS DCS Keycap set by ReallyBigTeeth
...eyboards with alps switches.
print right side up with support. sand the top surface for a more comfortable typing experience.
thingiverse
free
REVOMAZE Puzzle Grip by ReallyBigTeeth
...icator on the puzzle's core and tighten the screw.
the revomaze stand can be found here.
check out the revomaze website here.
thingiverse
free
Nexus 7 (2013) Laser Barcode Scanner (Symbol LS3408) by ReallyBigTeeth
...erse
if you like what you see here, consider leaving a tip.
combine a nexus 7 (2013) with a symbol ls3408 laser barcode scanner.
thingiverse
free
T8 Leadscrew Anti-Backlash Spacer by ReallyBigTeeth
.... the assembly is fastend together using m3 bolts. the model may need adjustment to get the correct thickness for your assembly.
thingiverse
free
REVOMAZE Stand - Remix by ReallyBigTeeth
...viewtopic.php?f=25&t=2430&p=55627#p55627
the revomaze puzzle grip can be found here.
check out the revomaze website here.
thingiverse
free
Digital Clock Case (Cardinal Model 6025 / 928) by ReallyBigTeeth
...al clock enclosure for cardinal alarm clock model 6025. basic model 928. uses battery door and buttons from original clock case.
thingiverse
free
Nexus 7 2013 Keyboard stand by ReallyBigTeeth
....
use a keyboard with your tablet while laying in bed, sitting in a chair, or at a desk.
assembly viideo
angle adjustment video
Paddles
thingiverse
free
paddle by Excupid
...paddle by excupid
thingiverse
paddle
thingiverse
free
paddle taco
...paddle taco
thingiverse
paddle taco
thingiverse
free
Swim Paddle / Trainer, Isolation Paddle by PSomeone
...trainer, isolation paddle by psomeone thingiverse isolation swim training paddles ...
thingiverse
free
Sculling paddles, swim Paddles, Training by PSomeone
...ning by psomeone
thingiverse
sculling paddles, designed around finns idea. see agility paddles this was remixed from for sizing.
thingiverse
free
Shift Paddles by andygreenegrass
...shift paddles by andygreenegrass
thingiverse
shift paddles for jkoljo's paddle shifters.
thingiverse
free
Paddles by gyuhasz
...paddles by gyuhasz
thingiverse
paddles for give aways etc. easy to print great for benchmark testing.
thingiverse
free
Bread Maker paddle
...bread maker paddle
thingiverse
paddle
thingiverse
free
paddle spinner by Zarmock
...paddle spinner by zarmock
thingiverse
paddle spinner
thingiverse
free
Paddle Holder by Skaterlion
...paddle holder by skaterlion
thingiverse
a paddle holder with a different design. should fit any standard size kayak paddle.
thingiverse
free
Toys Paddle Boat
...toys paddle boat
thingiverse
toys paddle boat
Narrow
thingiverse
free
Narrow Spoon by aman95
...narrow spoon by aman95
thingiverse
it is a spoon but narrow
thingiverse
free
Narrow Boat by wookieegunner
...narrow boat by wookieegunner
thingiverse
this is a narrowing of the boat by ege-ozgul by 50%
thingiverse
free
*Narrow Vice by imaicom
...*narrow vice by imaicom
thingiverse
narrow vise with m3 long screws to adjust the gap.
thingiverse
free
Narrow ClosetMaid Bracket
...ccommodate. this bracket is designed to sit directly on top of the trim and the screw holes are hidden within the support itself.
thingiverse
free
Narrow grinder for drill by YuvaArt
...inder for drill by yuvaart
thingiverse
made another grinder for the drill. designed for narrow holeshttps://youtu.be/0waanyj6dwa
thingiverse
free
*Narrow wall test by imaicom
...*narrow wall test by imaicom
thingiverse
a printed specimen on a narrow wall. please use it as a printer performance test.
thingiverse
free
Narrow Costume Dagger by GlitchTech
...costume dagger by glitchtech
thingiverse
a narrow dagger for use in costumes. it was based off of the hellequin daggers from ac.
thingiverse
free
Narrower slot
...h the slot in the case narrowed. it now works perfectly with my business cards - feeding one at a time and without any blockages.
thingiverse
free
Kazi narrow gauge tracks (with Lego narrow gauge adapters)
...n r40 curve as well as the openscad file used to generate them. of course, you can generate your own different lengths and radii.
thingiverse
free
Mini pcie narrower version. by MON5TERMATT
...mini pcie narrower version. by mon5termatt
thingiverse
just made this narrower for my t61 laptop.
Version
thingiverse
free
Shocker Hand Final Version.. New Full version !! ...KEYCHAIN Version Final by marc_1988
... by marc_1988
thingiverse
now 2 versions !! .... new full....
keychain version of shocker hand final
print,share, and have fun.
thingiverse
free
beafy version by Bemothelaiemo
...beafy version by bemothelaiemo
thingiverse
beafy version for fanless psu
thingiverse
free
Pumpkin Version 2
...pumpkin version 2
thingiverse
version 2 of my pumpkin.
thingiverse
free
Poro (Ekko version)
...poro (ekko version)
thingiverse
warlock3dmodels poro, but as an ekko version.
thingiverse
free
Better version by AlexMaker816
...better version by alexmaker816
thingiverse
better version of heart box
thingiverse
free
lite version by Mitche11S
...lite version by mitche11s
thingiverse
i built this model by analogy with the simplified version.
thingiverse
free
5015Blowerduct Inverted version
...5015blowerduct inverted version
thingiverse
inverted version of 5015blowerduct.
the spacer is used to prevent deflection.
thingiverse
free
Repaired version by Snake83
...repaired version by snake83
thingiverse
repaired version of the a https://www.thingiverse.com/thing:841122/#comments
thingiverse
free
thicker version by Finch666
...thicker version by finch666
thingiverse
thicker version, my original got warped under tension.
thingiverse
free
2016 version by totof60
...2016 version by totof60
thingiverse
just add the 2016 version
from http://www.thingiverse.com/thing:193755