Cults
Hot Rod
by Cults
Last crawled date: 6 years, 1 month ago
a model Hot Rod for the pinshape cosplay comp ( Tony Starks ) , I have used parts from my Freedom Roadster to produce it. The model is for personal use only ! It has complete Printing and assembly instructions. You could user finer setting on your printer other than suggested to produce a smoother finish. It can be printed over a number of days , You will need a few basic tools and small screws to assemble it. ( it could also be heat staked together with a soldering iron, make sure the area is well ventilated )
All stl files are numbered to easily find on your printer read out and follow in the instructions.
Model sizes
Front track- 185mm
Rear track- 193mm
Overall length-370mm
Body height-110mm
over all height-135mm
Max body width 147mm
front wheel dia. 75mm by 14mm wide ( white wall)
rear wheel dia.85mm by 19mm wide (white wall)
If you decide to paint make sure you use a undercoat or spray putty and sand super smooth before applying the top coat.
If Painting the flames should be done before you stick them to the body, You could also hand paint the flames on if you like.
I really enjoy designing for 3D printing and assembling, most parts have a flat surface to print from and only a few have support. It also has flex tires.
Don't be daunted by the number of parts, it assemblies together beautifully and you will enjoy the experience and the pleasure of viewing the model once finished.
As an option you can add your RC control gear to it can be housed in the boot and a servo near the drivers feet position. ( I am currently working to add this to the design)
Hotrod Model Assembly instructions By Chris Mc Connell
step procedure Part no.s Hardware tools
1 Attach and screw both front and rear rails to the floor - 1,2,3,4, 4g brass counter sunk brass wood screw 12mm long*4
2 Slide Drop Axle and Radiator on to front rails- 5-3,4
3 Place fins into grill surround (goes in on angle)
Clip on to Drop Axle and Radiator- 7,6,-5
4 Attach stub axles to drop axle- 9,10-5 M4 20mm long pan head
5 Attach long steering arm to both stub axles- 8 4g pan head self-taper*2
6 Attach steering arm to LHS stub axle- 11 4g pan head self-taper
7 Insert front beam into holes on front rails- 19,-4,3
8 Locate dowel pins of front stabilizers into floor holes and drop axle holes( take note of Left and right)- 38-1,5
9 Locate RHS and LHS head lights in locating holes in drop axle/front rails - 12-1,3,4
10 Locate rear stabilizers on rear spacers- 37,14
11 Locate rear stabilizers on to floor, from below into rear most slot, close to outside edge of floor- 37,1
12 Place long axle through rear spacers and rear rails (hole)- 13-14,37
13 Assemble front wheels and click on to stub axle
( Hold stub axle and push assembled wheel until home, then rotate until free to turn)-
15rimfront,
15front-white wall
17front-tyre
14 Assemble rear wheels & click on to rear axle (prt13)-
16rimrear
16rear-whitewall
18rear-tyre
15 Assemble red firewall and cowl together- 26,27 4g by 6mm long Pan head self-taper*2
16 Attach doors to cowl you need to cut down small brass/steel flat nails to 7.0 mm long. Then position the nail in the door hinge hole and locate it in position with the cowl hinge hole and push the nail through the hole to from the rotating pin for the door hinges, repeat for both doors.- 28,29-27 20mm long by 1.5mm dia. Brass nail ( cut down),
17 Locate steering wheel on dash steering mount and push dash into hole in cowl from behind. - 22,21-27
18 Locate together, cowl assembly to floor and screw together.
(*make sure the steering arm,8, is free to slide through the opening on the steering wheel side)- 27-1
19 Option push in pedals and pedals blank if required, in slots LHS,RHS - 24,25-1
20 Screw seat supports to base of seat Note Left and right sides place in slots on floor and screw into place form the sides.-
20,20a-1 4g 12mm long pan head self-taper*2
4g 6mm long pan head self-taper*2
21 Assemble block, heads, inlet manifold, joiner & auto
(Use 1.75 filament 8 mm long as dowel pins to locate block to heads and inlet.
Glue in joiner and auto to rear of block.
Use PVA glue and locate assembly on to chassis.- 31,32,33,35,34 PVA
22 Push the gear lever in to auto.- 23-34
23 locate boot and secure it with screws to the floor- 30-1 4g pan head self-taper*2
24 Option, and door handles to inside of doors
Screw into handle first then hold it on door and screw in, use care.- 41-28,29 4g counter sunk brass wood screw 12mm long*2
25 Glue in radiator pipes to radiator heads- 42,43 -32 -5 PVA
26 Locate window frames and position in holes in cowl- 39-27
27 Use template to cut out windscreen a fit to frames-
28 Position flames and mark door lines .Using a cutting board and Stanley knife cut to fit and glue into position-
Alternatively use the flames as a template and paint the flames, which could look better. 40 PVA or other
29 Fit exhaust manifolds to block push into place- 36 -31
30 Use some filament to add a couple of fuel lines to the carbies.
Hotrod Model
Printing Instructions
By Chris McConnell
number Name instructions colour settings
0.3mm layer height, with raft, 10 % infill
1 Floor Build flat on base
2 Rear rail 2 required Build on side
3 Front arm LHS Build on side with engine mount up Use supports
4 Front arm RHS Build on side with engine mount up Use supports
5 Drop Axle and Radiator Build flat on back face
6 Grill surround Lay on flat edge ( back ) 0.2mm layer,
use supports
7 Fins grill Lay on flat back RED 0.2mm layer
8 Long steering arm Lay flat on bed with supports use support
9 Front stub LHS Has supports modelled on it ( break off later)
10 Front stub RHS Has supports modelled on it ( break off later)
11 Steering arm Needs support have end boss flat on bed ( this is for servo option) 0.2mm layer
12 Head Lights Rotate stl file so dome sits on bed Neutral
(or paint chrome) 0.2mm layer
13 Long rear axle Flat on bed as opens
14 Rear spacer 2 required
Build standing up
15 Rim front
White wall 2 required. (black)
2 front-white walls inserts Inserts white
16 Rim rear
White wall 2 required. (black)
2 rear-white walls inserts Inserts white
17 Front tyre 2 required semi flex As per manufactures instructions. (15% infill)
18 Rear tyre 2 required semi flex As per manufactures instructions. (15% infill)
19 Front beam Flat on bed Grey
(or paint chrome) 0.2mm layer
20 Seat support 2 required, build on end standing up
20a seat Build on end standing up Red
21 dash Back of dash flat on bed neutral 0.2 layer
22 Steering wheel Build flat on bed 0.2 layer
23 Gear stick Build on flat side with knob up 0.2 layer
24 pedals Option, build standing on END
25 Pedals blank Option build standing on end
26 Firewall red Build flat side to bed red
27 Front cowl Build with firewall flat to bed, with supports use supports
28 LHS door Build standing on end with hinges at top
29 RHS door Build standing on end with hinges at top
30 boot Build on angle of 50 degrees does require cleaning up. builds quickest with minimal support.
31 V8 block Rear flat face on build table
32 Heads Build flat on bed
( modelled on an angle of 41dregees) RED
33 Inlet carb set flat face on build table
(has supports built on it, break off later) grey
(or paint chrome) 0.2layer
34 Auto Flat face on build table
35 Joiner Used to align block and auto
36 exhaust Build with supports, rotate to best build Grey (or paint chrome) 0.2 layer, use supports
37 Rear stabilizer 2 required ( lay flat)
38 Front stabilizers ( modelled on an angle of 7 degrees)
Rotate to flat on bed, use supports Neutral
(or paint chrome) 0.2 layer, use supports
39 Window frames Build standing up on round base
40 flames 2 required. Build flat on bed
Take care when removing from raft yellow 0.2 layer
41 Door handles 2 required (optional)
42 Wind screen Recycled clear plastic (box packaging sheet)
All stl files are numbered to easily find on your printer read out and follow in the instructions.
Model sizes
Front track- 185mm
Rear track- 193mm
Overall length-370mm
Body height-110mm
over all height-135mm
Max body width 147mm
front wheel dia. 75mm by 14mm wide ( white wall)
rear wheel dia.85mm by 19mm wide (white wall)
If you decide to paint make sure you use a undercoat or spray putty and sand super smooth before applying the top coat.
If Painting the flames should be done before you stick them to the body, You could also hand paint the flames on if you like.
I really enjoy designing for 3D printing and assembling, most parts have a flat surface to print from and only a few have support. It also has flex tires.
Don't be daunted by the number of parts, it assemblies together beautifully and you will enjoy the experience and the pleasure of viewing the model once finished.
As an option you can add your RC control gear to it can be housed in the boot and a servo near the drivers feet position. ( I am currently working to add this to the design)
Hotrod Model Assembly instructions By Chris Mc Connell
step procedure Part no.s Hardware tools
1 Attach and screw both front and rear rails to the floor - 1,2,3,4, 4g brass counter sunk brass wood screw 12mm long*4
2 Slide Drop Axle and Radiator on to front rails- 5-3,4
3 Place fins into grill surround (goes in on angle)
Clip on to Drop Axle and Radiator- 7,6,-5
4 Attach stub axles to drop axle- 9,10-5 M4 20mm long pan head
5 Attach long steering arm to both stub axles- 8 4g pan head self-taper*2
6 Attach steering arm to LHS stub axle- 11 4g pan head self-taper
7 Insert front beam into holes on front rails- 19,-4,3
8 Locate dowel pins of front stabilizers into floor holes and drop axle holes( take note of Left and right)- 38-1,5
9 Locate RHS and LHS head lights in locating holes in drop axle/front rails - 12-1,3,4
10 Locate rear stabilizers on rear spacers- 37,14
11 Locate rear stabilizers on to floor, from below into rear most slot, close to outside edge of floor- 37,1
12 Place long axle through rear spacers and rear rails (hole)- 13-14,37
13 Assemble front wheels and click on to stub axle
( Hold stub axle and push assembled wheel until home, then rotate until free to turn)-
15rimfront,
15front-white wall
17front-tyre
14 Assemble rear wheels & click on to rear axle (prt13)-
16rimrear
16rear-whitewall
18rear-tyre
15 Assemble red firewall and cowl together- 26,27 4g by 6mm long Pan head self-taper*2
16 Attach doors to cowl you need to cut down small brass/steel flat nails to 7.0 mm long. Then position the nail in the door hinge hole and locate it in position with the cowl hinge hole and push the nail through the hole to from the rotating pin for the door hinges, repeat for both doors.- 28,29-27 20mm long by 1.5mm dia. Brass nail ( cut down),
17 Locate steering wheel on dash steering mount and push dash into hole in cowl from behind. - 22,21-27
18 Locate together, cowl assembly to floor and screw together.
(*make sure the steering arm,8, is free to slide through the opening on the steering wheel side)- 27-1
19 Option push in pedals and pedals blank if required, in slots LHS,RHS - 24,25-1
20 Screw seat supports to base of seat Note Left and right sides place in slots on floor and screw into place form the sides.-
20,20a-1 4g 12mm long pan head self-taper*2
4g 6mm long pan head self-taper*2
21 Assemble block, heads, inlet manifold, joiner & auto
(Use 1.75 filament 8 mm long as dowel pins to locate block to heads and inlet.
Glue in joiner and auto to rear of block.
Use PVA glue and locate assembly on to chassis.- 31,32,33,35,34 PVA
22 Push the gear lever in to auto.- 23-34
23 locate boot and secure it with screws to the floor- 30-1 4g pan head self-taper*2
24 Option, and door handles to inside of doors
Screw into handle first then hold it on door and screw in, use care.- 41-28,29 4g counter sunk brass wood screw 12mm long*2
25 Glue in radiator pipes to radiator heads- 42,43 -32 -5 PVA
26 Locate window frames and position in holes in cowl- 39-27
27 Use template to cut out windscreen a fit to frames-
28 Position flames and mark door lines .Using a cutting board and Stanley knife cut to fit and glue into position-
Alternatively use the flames as a template and paint the flames, which could look better. 40 PVA or other
29 Fit exhaust manifolds to block push into place- 36 -31
30 Use some filament to add a couple of fuel lines to the carbies.
Hotrod Model
Printing Instructions
By Chris McConnell
number Name instructions colour settings
0.3mm layer height, with raft, 10 % infill
1 Floor Build flat on base
2 Rear rail 2 required Build on side
3 Front arm LHS Build on side with engine mount up Use supports
4 Front arm RHS Build on side with engine mount up Use supports
5 Drop Axle and Radiator Build flat on back face
6 Grill surround Lay on flat edge ( back ) 0.2mm layer,
use supports
7 Fins grill Lay on flat back RED 0.2mm layer
8 Long steering arm Lay flat on bed with supports use support
9 Front stub LHS Has supports modelled on it ( break off later)
10 Front stub RHS Has supports modelled on it ( break off later)
11 Steering arm Needs support have end boss flat on bed ( this is for servo option) 0.2mm layer
12 Head Lights Rotate stl file so dome sits on bed Neutral
(or paint chrome) 0.2mm layer
13 Long rear axle Flat on bed as opens
14 Rear spacer 2 required
Build standing up
15 Rim front
White wall 2 required. (black)
2 front-white walls inserts Inserts white
16 Rim rear
White wall 2 required. (black)
2 rear-white walls inserts Inserts white
17 Front tyre 2 required semi flex As per manufactures instructions. (15% infill)
18 Rear tyre 2 required semi flex As per manufactures instructions. (15% infill)
19 Front beam Flat on bed Grey
(or paint chrome) 0.2mm layer
20 Seat support 2 required, build on end standing up
20a seat Build on end standing up Red
21 dash Back of dash flat on bed neutral 0.2 layer
22 Steering wheel Build flat on bed 0.2 layer
23 Gear stick Build on flat side with knob up 0.2 layer
24 pedals Option, build standing on END
25 Pedals blank Option build standing on end
26 Firewall red Build flat side to bed red
27 Front cowl Build with firewall flat to bed, with supports use supports
28 LHS door Build standing on end with hinges at top
29 RHS door Build standing on end with hinges at top
30 boot Build on angle of 50 degrees does require cleaning up. builds quickest with minimal support.
31 V8 block Rear flat face on build table
32 Heads Build flat on bed
( modelled on an angle of 41dregees) RED
33 Inlet carb set flat face on build table
(has supports built on it, break off later) grey
(or paint chrome) 0.2layer
34 Auto Flat face on build table
35 Joiner Used to align block and auto
36 exhaust Build with supports, rotate to best build Grey (or paint chrome) 0.2 layer, use supports
37 Rear stabilizer 2 required ( lay flat)
38 Front stabilizers ( modelled on an angle of 7 degrees)
Rotate to flat on bed, use supports Neutral
(or paint chrome) 0.2 layer, use supports
39 Window frames Build standing up on round base
40 flames 2 required. Build flat on bed
Take care when removing from raft yellow 0.2 layer
41 Door handles 2 required (optional)
42 Wind screen Recycled clear plastic (box packaging sheet)
Similar models
grabcad
free
Stub Axle RH
...drive vehicle. in a rear wheel drive vehicle this axle is capable of angular movement about the kingpin for steering the vehicle.
thingiverse
free
Double Decker City Bus - HO Scale by Stretch57
...allow glass installation on the exterior of the bus similar to the prototype. -doors are painted and glue to...
thingiverse
free
BBM Paint Storage (for screwing to a shelf) by DaringD
...an head screws as long as they need to be, but 2cm is more than enough. pre drill 2mm pilot holes in the wood using the template!
grabcad
free
Front knuckle
...front knuckle
grabcad
the knuckle is used as a connecting fixture for stub axle, a arms, brake caliper and steering mounts
grabcad
free
Wheely King Axle lock out adapter
...axle lock out to clean up and simplify the look and function of non steering rear axles . uses the stock axle stubs and bearings.
grabcad
free
Right stub axle & steering arm (Cart project)
...right stub axle & steering arm (cart project)
grabcad
right stub axle & steering arm
grabcad
free
Stub Axle Assembly
...stub axle assembly
grabcad
stub axle assembly for a go kart
grabcad
free
volkswagen golf iii rear stub axle
...volkswagen golf iii rear stub axle
grabcad
volkswagen golf iii rear stub axle
thingiverse
free
OpenRc F1 front axle by nicklindenmuth
...e front hub with enlarged hole for a single steering bolt through the whole thing and steering endstops. uses two 25mm m3 screws.
thingiverse
free
SCX10 Steering guard Defender 90
...e/servo depth. i also have the front bumper as close to the chassis as possible, may require a slight trim on the mounting posts.
Hotrod
turbosquid
$30
Hotrod
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
Hotrod
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$25
Titan Hotrod
... nfshs one ps ps1 psone rod speed sports stakes titan transport vehicle
quality exterior and low polygon interior concept hotrod.
3d_export
$5
cartoon hotrod
...cartoon hotrod
3dexport
3d_export
$99
HotRod 3D Model
...od 3d model
3dexport
hotrod hot rod muscle car race drag dragster vintage classic chopper
hotrod 3d model bayazoff 41954 3dexport
turbosquid
$5
Cartoon Hotrod
...model cartoon hotrod for download as obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1513572)
turbosquid
$39
Hotrod car
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
HotRod Wheel
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
hotrod hemi
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$39
Hotrod 3D Model
...hotrod 3d model
3dexport
ground transport car
hotrod 3d model fluger 39468 3dexport
1930
3ddd
$1
1930s Vintage Tricycle
...1930s vintage tricycle
3ddd
велосипед
model of 1930´s tricycle.
3ddd
$1
VINTAGE 1930 KODAK
...vintage 1930 kodak
3ddd
камера , kodak
vintage 1930 kodak
3ddd
$1
DURAVIT 1930 Series
...duravit 1930 series
3ddd
duravit , угловой
угловая раковина duravit 1930 series
3ddd
$1
DURAVIT 1930 Series
...duravit 1930 series
3ddd
duravit
раковина duravit 1930 series с пьедесталом
turbosquid
$6
barker serie 1930
...y free 3d model barker serie 1930 for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1336137)
3ddd
$1
Унитаз Duravit 1930 SERIES
... series
#018209http://www.duravit.com/website/homepage/products/product_overview/series/1930_series.com-en.html/p-90431
turbosquid
$60
1930s Auto Racer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
PACKARD SPEEDSTER 1930
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Entrance door - 1930
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Mauser 1930+fbx
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
V8
3d_export
$25
v8 - engine
...v8 - engine
3dexport
detailed 3d model engine v8 6.6l - duramax made in 3ds max
turbosquid
free
V8 5.8L
...id
free 3d model v8 5.8l for download as blend, obj, and dae on turbosquid: 3d models for games, architecture, videos. (1687696)
turbosquid
$12
Cupcake V8
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
v8 Engine
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$80
V8 Engine 3D Model
...v8 engine 3d model
3dexport
engine v8 turbo car part
v8 engine 3d model antonyart 1037 3dexport
3d_export
$99
Fiat V8 3D Model
...fiat v8 3d model
3dexport
car classic v8 fiat sport coupe old
fiat v8 3d model desmonster 51326 3dexport
cg_studio
$199
V8 Engine3d model
...v8 engine3d model
cgstudio
.3ds - v8 engine 3d model, royalty free license available, instant download after purchase.
3d_export
$5
v8-gm-350-turbosnapshot7
...v8-gm-350-turbosnapshot7
3dexport
v8-gm-350-turbo.snapshot.7
3d_export
$8
Bunker Light v8
...bunker light v8
3dexport
3d_export
$10
Peugeot 909 V8 3D Model
...peugeot 909 v8 3d model
3dexport
peugeot v8
peugeot 909 v8 3d model azrim27 21445 3dexport
Rc
3ddd
$1
RC Helicopter
...rc helicopter
3ddd
вертолет
mini rc helicopter
93.329 polys
3d_export
$7
rc helicopter model
...rc helicopter model
3dexport
rc helicopter model
3d_ocean
$25
RC F1
...rc f1
3docean
auto car control f1 formula race rc remote speed
remote control f1 car
turbosquid
$10
rc plane
...lane
turbosquid
free 3d model rc plane for download as blend on turbosquid: 3d models for games, architecture, videos. (1295828)
turbosquid
$100
RC Helicopter
...free 3d model rc helicopter for download as 3ds, max, and obj on turbosquid: 3d models for games, architecture, videos. (1298511)
turbosquid
$59
Drone with RC
...3d model drone with rc for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1363601)
turbosquid
$75
RC buggy
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$39
RC Plane001
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$30
RC Jet
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$30
Rc airplane
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Ford
3ddd
$1
Ford A
...ford a
3ddd
ford
ford a.
длина: 4191 мм
ширина: 1702 мм
3ddd
$1
Ford Fusion
...ford fusion
3ddd
ford
ford fusion
3ddd
$1
Ford 32
...ford 32
3ddd
ford
ford 32 tuning
3ddd
$1
Ford Focus
...ford focus
3ddd
ford
двухместный ford focus
3ddd
$1
Ford focus
...ford focus
3ddd
ford focus
3d_export
$10
Ford-transit
...ford-transit
3dexport
ford-transit van
3d_export
$69
ford-mondeo ford-fusion
...vertisements or games corona render and materials all textures include in *.rar files lighting setup is not included in the file!
3d_ocean
$69
Ford Mustang
...n
car ford mustang speed wheel
ford mustang high poly with details and materials used materials are included /.3ds/.obj/.fbx/.skp
3d_export
$30
Ford 3D Model
...ford 3d model
3dexport
ford
ford 3d model afshin 37528 3dexport
3ddd
$1
Автосалон FORD
...он ford
3ddd
автосалон , здание
автосалон ford. выдерживает крупные ракурсы. всем удачи!
Auto
3d_export
$5
auto
...auto
3dexport
auto
3ddd
$1
auto
...auto
3ddd
max7
turbosquid
$69
AUTO
...to
turbosquid
royalty free 3d model auto for download as obj on turbosquid: 3d models for games, architecture, videos. (1453538)
3d_export
$10
Auto
...auto
3dexport
3d_export
free
auto
...auto
3dexport
3ddd
$1
Auto posters
...auto posters
3ddd
машина
auto posters
turbosquid
$50
auto
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$28
Auto
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
auto
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
auto
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Hot
turbosquid
$1
HOT
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$12
Hot Tub
...hot tub
3dexport
hot tub - 4k png/tif textures
3d_export
$9
Hot Tub
...hot tub
3dexport
hot tub - 4k png/tif textures
3d_export
free
hot chili
...hot chili
3dexport
hot chili<br>for fruits and getegables collection
3d_export
$5
hot air balloon
...hot air balloon
3dexport
hot air balloon
3d_export
free
Hot dog shop
...hot dog shop
3dexport
hot dog shop
turbosquid
$90
hot venue
...rbosquid
royalty free 3d model hot venue for download as fbx on turbosquid: 3d models for games, architecture, videos. (1336949)
turbosquid
$20
Hot Rod
...
turbosquid
royalty free 3d model hot rod for download as ma on turbosquid: 3d models for games, architecture, videos. (1351690)
turbosquid
$14
Hot Pepper
...bosquid
royalty free 3d model hot pepper for download as obj on turbosquid: 3d models for games, architecture, videos. (1611643)
turbosquid
$1
Hot dog
...turbosquid
royalty free 3d model hot dog for download as max on turbosquid: 3d models for games, architecture, videos. (1450961)
Rod
archibase_planet
free
Rod
...rod
archibase planet
shank rod
so rod - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Spinning rod
...g rod
archibase planet
spinning rod spinning rod fishing-rod
spinning rod - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
rod handle
...rod handle
3dexport
rod handle
3ddd
$1
bench with rods
...bench with rods
3ddd
скамейка
bench with rods
3ddd
$1
диван ROD
...диван rod
3ddd
rod , living divani
http://www.livingdivani.it/
3ddd
$1
кресло ROD
...кресло rod
3ddd
rod , living divani
http://www.livingdivani.it/
design_connected
$18
Rod Armchair
...rod armchair
designconnected
living divani rod armchair computer generated 3d model. designed by lissoni, piero.
archive3d
free
Rod 3D Model
...rod 3d model
archive3d
shank rod
so rod - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$15
Fishing rod
...urbosquid
royalty free 3d model fishing rod for download as on turbosquid: 3d models for games, architecture, videos. (1684756)
archive3d
free
Spinning rod 3D Model
...d spinning rod fishing-rod
spinning rod - 3d model (*.gsm+*.3ds) for interior 3d visualization.
Toy
3d_export
$5
toys
...toys
3dexport
toys
archibase_planet
free
Toy
...toy
archibase planet
giraffe toy toy giraffe
toy giraffe n041010 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Toy
...toy
archibase planet
elephant toy toy plaything
toy elephant n131010 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Toy
...toy
archibase planet
toy deer
toy n061011 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Toy
...toy
archibase planet
nutcracker toy
toy n070111 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Toy
...toy
archibase planet
toy nutcracker
toy n190811 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Toy
...toy
archibase planet
toy snake serpent
toy n181112 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Toy
...toy
archibase planet
toy elephant
toy elephant n040112 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Toy
...toy
archibase planet
toy hare
toy a hare n311210 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Toy
...toy
archibase planet
toy rabbit
toy s n150412 - 3d model (*.3ds) for interior 3d visualization.
Car
3d_export
$5
car
...car
3dexport
luxury car high quality car
3d_export
$5
car
...car
3dexport
luxury car high quality car
3d_export
$5
car
...car
3dexport
luxury car high quality car
3d_export
$5
car
...car
3dexport
luxury car high quality car
3d_export
$5
car
...car
3dexport
luxury car high quality car
archibase_planet
free
Car
...
archibase planet
car sports car motor-car sportster
car nascar#1 n300114 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Car
...ibase planet
car motor-car sportster sports car
car gablota xform n190214 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Car
...car
archibase planet
car motor car transport
car vaz 2104- 3d model for interior 3d visualization.
3d_export
$15
car
...car
3dexport
car
3d_export
free
car
...car
3dexport
car